mediatek: filogic: add support for Huasifei WH3000
The Huasifei WH3000 eMMC model (aka Fudy MT3000) is a Wi-Fi 6 5G
cellular router based on MediaTek MT7981A SoC.
Specifications:
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8G
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
UART: 3.3V, TX, RX, GND / 115200 8N1
Installation via U-Boot rescue:
Connect to the GbE eth port, then press and hold reset button while
booting the device. Wait for the Internet led to blink 5 times,
release reset button. The rescue page is accessible via http://192.168.1.1
Select the OpenWrt sysupgrade image and start upgrade.
Wait for the router to flash new firmware and reboot.
(cherry picked from commit f310b8c74e)
This commit is contained in:
coolsnowwolf
@@ -61,7 +61,8 @@ acer,vero-w6m|\
|
||||
glinet,gl-mt2500|\
|
||||
glinet,gl-mt6000|\
|
||||
glinet,gl-x3000|\
|
||||
glinet,gl-xe3000)
|
||||
glinet,gl-xe3000|\
|
||||
huasifei,wh3000-emmc)
|
||||
local envdev=$(find_mmc_part "u-boot-env")
|
||||
ubootenv_add_uci_config "$envdev" "0x0" "0x80000"
|
||||
;;
|
||||
@@ -93,6 +94,7 @@ konka,komi-a31)
|
||||
cetron,ct3003|\
|
||||
edgecore,eap111|\
|
||||
h3c,magic-nx30-pro-nmbm|\
|
||||
livinet,zr-3020|\
|
||||
netgear,wax220|\
|
||||
zbtlink,zbt-z8102ax|\
|
||||
zbtlink,zbt-z8103ax)
|
||||
@@ -111,9 +113,6 @@ gatonetworks,gdsp)
|
||||
glinet,gl-mt3000)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000"
|
||||
;;
|
||||
livinet,zr-3020)
|
||||
ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000" "1"
|
||||
;;
|
||||
mercusys,mr90x-v1|\
|
||||
routerich,ax3000|\
|
||||
tplink,re6000xd)
|
||||
|
||||
@@ -0,0 +1,199 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "mt7981.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Huasifei WH3000 eMMC version";
|
||||
compatible = "huasifei,wh3000-emmc", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
serial0 = &uart0;
|
||||
led-boot = &wlan_led;
|
||||
led-failsafe = &wlan_led;
|
||||
led-upgrade = &wlan_led;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs = "root=PARTLABEL=rootfs rootwait rootfstype=squashfs,f2fs";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory@40000000 {
|
||||
reg = <0 0x40000000 0 0x40000000>;
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-mode {
|
||||
label = "mode";
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
wan_led: led-0 {
|
||||
function = LED_FUNCTION_WAN;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
wlan_led: led-1 {
|
||||
function = LED_FUNCTION_WLAN;
|
||||
color = <LED_COLOR_ID_WHITE>;
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
usb_vbus: regulator-usb {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb-vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
regulator-boot-on;
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&mdio_pins>;
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
nvmem-cells = <&macaddr_factory_4 2>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
phy-mode = "2500base-x";
|
||||
phy-handle = <&phy1>;
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
nvmem-cells = <&macaddr_factory_4 3>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
phy-mode = "gmii";
|
||||
phy-handle = <&int_gbe_phy>;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio_bus {
|
||||
phy1: ethernet-phy@1 {
|
||||
compatible = "ethernet-phy-ieee802.3-c45";
|
||||
reg = <1>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupt-parent = <&pio>;
|
||||
reset-assert-us = <100000>;
|
||||
reset-deassert-us = <100000>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_LOW>;
|
||||
realtek,aldps-enable;
|
||||
};
|
||||
};
|
||||
|
||||
&mmc0 {
|
||||
bus-width = <8>;
|
||||
cap-mmc-highspeed;
|
||||
max-frequency = <52000000>;
|
||||
no-sd;
|
||||
no-sdio;
|
||||
non-removable;
|
||||
pinctrl-names = "default", "state_uhs";
|
||||
pinctrl-0 = <&mmc0_pins_default>;
|
||||
pinctrl-1 = <&mmc0_pins_uhs>;
|
||||
vmmc-supply = <®_3p3v>;
|
||||
status = "okay";
|
||||
|
||||
card@0 {
|
||||
compatible = "mmc-card";
|
||||
reg = <0>;
|
||||
|
||||
block {
|
||||
compatible = "block-device";
|
||||
|
||||
partitions {
|
||||
block-partition-factory {
|
||||
partname = "factory";
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x4 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
mmc0_pins_default: mmc0-pins-default {
|
||||
mux {
|
||||
function = "flash";
|
||||
groups = "emmc_45";
|
||||
};
|
||||
};
|
||||
|
||||
mmc0_pins_uhs: mmc0-pins-uhs {
|
||||
mux {
|
||||
function = "flash";
|
||||
groups = "emmc_45";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
status = "okay";
|
||||
|
||||
band@1 {
|
||||
reg = <1>;
|
||||
nvmem-cells = <&macaddr_factory_4 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
vbus-supply = <&usb_vbus>;
|
||||
};
|
||||
@@ -49,6 +49,10 @@ glinet,gl-xe3000)
|
||||
ucidef_set_led_netdev "wlan2g" "WLAN2G" "green:wifi2g" "phy0-ap0"
|
||||
ucidef_set_led_netdev "wlan5g" "WLAN5G" "green:wifi5g" "phy1-ap0"
|
||||
;;
|
||||
huasifei,wh3000-emmc)
|
||||
ucidef_set_led_netdev "wan" "WAN" "red:wan" "eth1"
|
||||
ucidef_set_led_netdev "wlan" "WLAN" "white:wlan" "phy1-ap0"
|
||||
;;
|
||||
imou,lc-hx3001|\
|
||||
nokia,ea0326gmp)
|
||||
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1" "link"
|
||||
|
||||
@@ -67,7 +67,8 @@ mediatek_setup_interfaces()
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan"
|
||||
;;
|
||||
bananapi,bpi-r3-mini|\
|
||||
edgecore,eap111)
|
||||
edgecore,eap111|\
|
||||
huasifei,wh3000-emmc)
|
||||
ucidef_set_interfaces_lan_wan eth0 eth1
|
||||
;;
|
||||
bananapi,bpi-r4|\
|
||||
|
||||
@@ -105,6 +105,7 @@ platform_do_upgrade() {
|
||||
glinet,gl-mt6000|\
|
||||
glinet,gl-x3000|\
|
||||
glinet,gl-xe3000|\
|
||||
huasifei,wh3000-emmc|\
|
||||
smartrg,sdg-8612|\
|
||||
smartrg,sdg-8614|\
|
||||
smartrg,sdg-8622|\
|
||||
@@ -212,6 +213,7 @@ platform_copy_config() {
|
||||
glinet,gl-mt6000|\
|
||||
glinet,gl-x3000|\
|
||||
glinet,gl-xe3000|\
|
||||
huasifei,wh3000-emmc|\
|
||||
jdcloud,re-cp-03|\
|
||||
smartrg,sdg-8612|\
|
||||
smartrg,sdg-8614|\
|
||||
|
||||
@@ -952,6 +952,23 @@ define Device/h3c_magic-nx30-pro-nmbm
|
||||
endef
|
||||
TARGET_DEVICES += h3c_magic-nx30-pro-nmbm
|
||||
|
||||
define Device/huasifei_wh3000-emmc
|
||||
DEVICE_VENDOR := Huasifei
|
||||
DEVICE_MODEL := WH3000 eMMC
|
||||
DEVICE_ALT0_VENDOR := Fudy
|
||||
DEVICE_ALT0_MODEL := MT3000
|
||||
DEVICE_DTS := mt7981b-huasifei-wh3000-emmc
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware f2fsck mkf2fs \
|
||||
kmod-usb-net-cdc-mbim kmod-usb-net-qmi-wwan kmod-usb-serial-option \
|
||||
kmod-usb3 automount uqmi
|
||||
KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb
|
||||
KERNEL_INITRAMFS := kernel-bin | lzma | \
|
||||
fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
endef
|
||||
TARGET_DEVICES += huasifei_wh3000-emmc
|
||||
|
||||
define Device/imou_lc-hx3001
|
||||
DEVICE_VENDOR := Imou
|
||||
DEVICE_MODEL := LC-HX3001
|
||||
|
||||
Reference in New Issue
Block a user