This commit adds support for the Hasivo F5800W-12S+ 12-port SFP+ switch.
Based on board revision `RTL_12S+ v1.01`.
Hardware
--------
| | |
|----------|----------------------------------------------------------------|
| SoC | RTL9313 rev B |
| RAM | 512 MB Samsung K4B4G1646E |
| Flash | 32 MB Macronix MX25L25645G SPI NOR, 29 MB usable by OpenWrt |
| Ethernet | 12x SFP+ via SoC (10G/2.5G/1G) |
| LEDs | 12x green 10G link, 12x green 1G link, |
| | 3x green power and PSUs -- no system status LED |
| Button | Reset |
| Console | RJ45 38400 bps 8n1 |
| Watchdog | via Hasivo MCU |
| Power | 2x internal 100-240V AC PSUs with 2x C14 inputs |
| Clock | NXP PCF8563 with coin cell battery |
| Fans | 2x 40mm case fan via Hasivo MCU |
Installing OpenWrt
------------------
1. Attach to RJ45 serial console port using a cisco cable.
2. Attach SFP to port 12.
3. Serve initramfs-kernel.bin on TFTP 192.168.1.111.
4. Power on the device.
5. Interrupt U-Boot by pressing `Ctrl+c`, then `z`, then `h`, during 3 second countdown.
6. Bring up networking: `rtk network on ; rtk 10g 55 fiber10g`.
7. Boot from TFTP: `tftpboot 0x84f00000 initramfs-kernel.bin ; bootm 0x84f00000`.
8. Use `mtd dump` to make backups of all flash partitions.
9. Use SCP to copy `squashfs-sysupgrade.bin` to the device, then run `sysupgrade`.
Restoring factory firmware
--------------------------
OpenWrt uses the `RUNTIME` and `RUNTIME2` partitions as one combined partition.
To restore them from backups, boot from `initramfs-kernel.bin` just like during
the installation, then use `mtd write` to write your backups of the factory
`mtd5` and `mtd6` partitions to the live `mtd5` partition.
Notes/Quirks
------------
- U-Boot interruption is obfuscated. Press `Ctrl+c`, then `z`, then `h`,
during the 3 second countdown.
- MAC address is stored on the `RUNTIME` or `RUNTIME2` partitions,
which are used by OpenWrt. Instead, we generate one random MAC address
and store it in the U-Boot environment.
- There is no system status LED. The three non-network LEDs are for
primary PSU (MS label), secondary PSU (SL), and powered on/off (PW).
Signed-off-by: Lars Gierth <larsg@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/23443
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
With the upcoming addition of the Hasivo F5800W-12S+ switch model,
another invariant of the u-boot env ethaddr fixup will be neccessary.
While previously all devices used the exact "zero" dummy ethaddr,
this new Hasivo ends in :10 instead of :00.
Make the hack work based on the 5-byte prefix of the ethaddr.
The currently known possible values for the 6th byte are 0x00 and 0x10.
This can be further expanded in the future if neccessary.
The separate XGS1010-12-A1 case doesn't need to deal with ethaddr prefixes
as it only covers one single device with one single dummy ethaddr.
Also use this opportunity to add more documentation,
and extract the common json and fw_setenv logic to a separate function.
Signed-off-by: Lars Gierth <larsg@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/23443
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
I think these were copied from a different device's DTS at the very
beginning of the porting work. We don't know the actual maximums
of these SFP ports, so let's stick with the 1W default, unless someone
researches what the Hasivo vendor firmware does for this setting.
Signed-off-by: Lars Gierth <larsg@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/23865
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This commit adds support for the Hasivo F1100W-4SX-4XGT ethernet 10Gbase and PoE switch.
It also adds support for a whole matrix of variants of this device:
| Device | Revision | RAM | PoE | Console |
|---------------------|----------|--------|-----|----------|
| F1100W-4SX-4XGT | v1.03 | 256 MB | n/a | RJ45 |
| F1100W-4SX-4XGT | v1.02 | 512 MB | n/a | RJ45 |
| F1100W-4SX-4XGT-SE | v1.03 | 256 MB | n/a | internal |
| F1100W-4SX-4XGT-SE | v1.02 | 512 MB | n/a | internal |
| F1100WP-4SX-4XGT | v1.03 | 256 MB | yes | RJ45 |
| F1100WP-4SX-4XGT | v1.02 | 512 MB | yes | RJ45 |
| F1100WP-4SX-4XGT-SE | v1.03 | 256 MB | yes | internal |
| F1100WP-4SX-4XGT-SE | v1.02 | 512 MB | yes | internal |
The devices are identical except for presence of the PoE daughter board,
RJ45 console port, and 256 or 512 MB RAM.
The non-512 MB image also works on the older 512 MB board revisions, but not vice versa.
Credit to @mensi @bevanweiss @markc1984
Hardware
--------
| | |
|----------|-----------------------------------------------------------|
| SoC | RTL9303 rev B |
| RAM | 256 MB Samsung K4B2G1646F DDR3L (board revision v1.03), |
| | or 512 MB unknown module (board revision v1.02 and older) |
| Flash | 32 MB Macronix MX25L25645G SPI NOR, |
| | 29 MiB usable by OpenWrt |
| Ethernet | 4x SFP+ via SoC (10G/2.5G/1G), |
| | 4x RJ45 via 4x RTL8261BE PHY (10G/5G/2.5G/1G/100M/10M) |
| PoE | only on WP variants |
| | 1x 802.3bt 90 W (port 5) |
| | 3x 802.3at 30 W (ports 6, 7, 8) |
| | via daughter board with Hasivo HS104PTI controller |
| | PoE works but is unmanaged --> future work |
| LEDs | 1x system orange/green, 8x link green/red, 4x PoE orange |
| Button | Reset |
| Console | RJ45 38400 bps 8n1, or pin holes on SE variants |
Installing OpenWrt
------------------
Note: With vendor firmware 7.1.9, the bootloader's network profile is broken.
We need to select a different profile with port/phy overlap to make the TFTP
transfer work. Then only port 5 works in the OpenWrt initramfs, but all ports
work fine after flashing, when we don't need the profile trick anymore.
1. Attach to RJ45 serial console port using a cisco cable.
2. Attach your computer to Port 5 (the first RJ45 port).
3. Serve initramfs-kernel.bin on TFTP 192.168.1.111.
4. Power on the device.
5. Interrupt U-Boot by pressing `Ctrl+C`, then `Z`, then `H`, during 3 second countdown.
6. Run: `setenv boardmodel 'RTL9303_5x8261BE_2XGE_ZHIHUI' ; rtk network on`
7. Run: `tftpboot 0x84f00000 initramfs-kernel.bin ; bootm 0x84f00000`
8. Use `mtd dump` to make backups of all flash partitions.
9. Use SCP to copy `squashfs-sysupgrade.bin` to the device, then run `sysupgrade`.
Restoring factory firmware
--------------------------
OpenWrt uses the `RUNTIME` and `RUNTIME2` partitions as one combined partition.
To restore them from backups, boot from `initramfs-kernel.bin` just like during
the installation, then use `mtd write` to write your backups of the factory
`mtd5` and `mtd6` partitions.
Notes/Quirks
------------
- U-Boot interruption is obfuscated. Press `Ctrl+C`, then `Z`, then `H`,
during the 3 second countdown.
- U-Boot rtk network profile is broken. Use the `RTL9303_5x8261BE_2XGE_ZHIHUI` profile
instead, it makes at least port 5 work.
- MAC address is stored on the `RUNTIME` or `RUNTIME2` partitions, which are used by OpenWrt.
Instead, we generate one random MAC address and store it in the U-Boot environment.
- PoE works but is unmanaged. The HS104 driver is worked on in
https://github.com/openwrt/openwrt/pull/22245 and will work with ethtool and the
kernel's new `pse-pd` subsystem.
Signed-off-by: Lars Gierth <larsg@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/23020
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
This patch backports a small but important part of the upstream commit:
b3f1b9e2aa07 build: Remove INCLUDE_MEMORY [PR117737]
Its original commit message fails to mention that the commit also moves
the `#include <memory>` to an earlier position within system.h,
which is the actual change that we're after in this patch.
Building our GCC 14.3 with host GCC 16, the inclusion order starts to matter,
which is an issue that was also touched upon by the upstream commits:
9970b576b7e4 Include safe-ctype.h after C++ standard headers, to avoid over-poisoning
f6e00226a4ca build: Move sstream include above safe-ctype.h {PR117771]
Signed-off-by: Lars Gierth <larsg@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/23095
Signed-off-by: Robert Marko <robimarko@gmail.com>
