On the TSN and RED variants of SparX-5 and LAN969x TAS (Time-Aware Shaper)
is present in the silicon.
Currently, the driver does not use configure it at all, which means that
the TAS_PROFILE_CONFIG.LINK_SPEED[1] value is left at the default of 3
which means that its configured for 1 Gbps.
So, running iperf between two 10G switch ports will result in only 940-ish
Mbps while we should be getting around 9.3 Gbps.
Correctly populating the TAS_PROFILE_CONFIG.LINK_SPEED[1] with the current
port speed fixes this issue and we achieve around 9.4 Gbps between two 10G
switch ports.
So, port the TAS port link speed setting from the vendor BSP 6.18 kernel[2]
[1] https://microchip-ung.github.io/lan969x-industrial_reginfo/reginfo_LAN969x-Industrial.html?select=hsch,tas_profile_cfg,tas_profile_config,link_speed
[2] https://github.com/microchip-ung/linux/tree/bsp-6.18-2026
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since 6.18 RTL8261N support was added to the generic Realtek PHY driver
and was dropped from the downstream driver.
So, fix the missing RTL8261N support by including the Realtek PHY kmod
and the relevant firmware.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Selection of Sparx5 hwmon driver for LAN969x was upstreamed, so use that
instead of the downstream patch.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, MDIO driver will print the probe defferal as error.
So, instead of spaming the log, backport the upstream fix for it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Lets refresh the config as generic config was wastly updated, and we
need the CONFIG_PAGE_BLOCK_MAX_ORDER to be defined.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, sysupgrade will only upgrade the unused slot, however since the
whole dual firmware logic is in the bootscript U-boot will just use the
first bootscript it finds.
So, in a case that you are running slot A it will upgrade slot B, however
that means that slot B will be still booted by the old bootscript that came
with the previous firmware version.
This is an issue if you need to change anything, so lets add a custom
function that upgrades the active bootscript as well after flashing the
slot firmware.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Methode uDPU and eDPU devices are one of the rare ones with a completely
custom image format being used with custom partition table with F2FS.
Instead of converting the boards to dual firmware (A/B style) and further
expand the already convoluted custom scripts, especially considering that
dual firmware conversion is a breaking change anyway, lets convert to using
the generic eMMC sysupgrade based images.
F2FS ZSTD compression is preserved thanks to fstools now supporting its use
on overlays.
Dual firmware support is implemented via U-Boot scripts so no U-Boot
upgrade is required.
Since there is a partition table layout change, eMMC must be wiped and
reflashed with the generated GPT image from OpenWrt initramfs.
Then on each sysupgrade the firmware slot will be altered.
Instructions:
1. Boot into OpenWrt initramfs
2. Copy openwrt-mvebu-cortexa53-methode_edpu-squashfs-emmc-gpt.img.gz to
the device into /tmp
3. Erase eMMC:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
4. Extract image
gzip -d /tmp/openwrt-mvebu-cortexa53-methode_edpu-squashfs-emmc-gpt.img.gz
5. Flash image
dd if=/tmp/openwrt-mvebu-cortexa53-methode_edpu-squashfs-emmc-gpt.img of=/dev/mmcblk0
6. Reboot
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
1bf2d490484e libfstools: make get_var_from_file() reusable
0b6022439cad mount_root: add kernel parameter to specify the overlay storage name
e600d842ce81 mount_root: add kernel parameter to specify the overlay fileystem type
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, moving from a port on one LAN8814 PHY package to another results
in a no traffic flowing on that new port.
It was tracked down to upstream change that fixed the issue that QSGMII
was soft reset on .config_init of each of 4 PHY-s in the package resulting
in a temporary traffic loss until QSGMII resynced.
However, it seems that the QSGMII soft reset timing is crucial and doing
the reset during probe only cause the QSGMII link to become partially
unsynced (Like 2 or 3 lanes are not synced).
So, add an upstream pending patch[1] to fix this, patch was modified as we
dont have the inband caps currently.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20260428134138.1741253-1-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
libcody will fail to build if building using a GCC16 host compiler, so
backport the upstream fix.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
These symbols depend on rustc version and is autodetected and set, so make
sure to filter them out.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We patch DMA_BUF to make it tristate, so once ALL_KMODS is selected it will
be built as a module even if previously disabled in the config.
So, since IO_URING_ZCRX does not depend on DMA_BUF linking will fail with:
aarch64-openwrt-linux-musl-ld: Unexpected GOT/PLT entries detected!
aarch64-openwrt-linux-musl-ld: Unexpected run-time procedure linkages detected!
aarch64-openwrt-linux-musl-ld: io_uring/zcrx.o: in function `io_release_dmabuf':
io_uring/zcrx.c:94:(.text+0x20): undefined reference to `dma_buf_unmap_attachment_unlocked'
aarch64-openwrt-linux-musl-ld: io_uring/zcrx.c:97:(.text+0x30): undefined reference to `dma_buf_detach'
aarch64-openwrt-linux-musl-ld: io_uring/zcrx.c:99:(.text+0x3c): undefined reference to `dma_buf_put'
aarch64-openwrt-linux-musl-ld: io_uring/zcrx.o: in function `io_import_dmabuf':
io_uring/zcrx.c:125:(.text+0x1b20): undefined reference to `dma_buf_get'
aarch64-openwrt-linux-musl-ld: io_uring/zcrx.c:132:(.text+0x1b34): undefined reference to `dma_buf_attach'
aarch64-openwrt-linux-musl-ld: io_uring/zcrx.c:139:(.text+0x1b48): undefined reference to `dma_buf_map_attachment_unlocked'
make[6]: *** [scripts/Makefile.vmlinux:72: vmlinux.unstripped] Error 1
So, lets use IS_REACHABLE() to check for CONFIG_DMA_SHARED_BUFFER instead
to avoid adding a dependency to CONFIG_DMA_SHARED_BUFFER.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
As preparation for enabling 6.18 kernel, rename the existing config to a
version specific 6.12 config.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Expand the FIP partition size to future proof and allow custom firmware
to be used as BL31 instead of U-Boot.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
LAN969x DTS was finally merged upstream, so lets backport the backported
DTS instead of keeping a local copy.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tactical 1000 has per per port RS0 and RS1 pins, however internally they
are tied together.
So, model them as RS0 at least.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
SFP I2C buses for ports 1 and 3 were swapped as order changed on production
boards.
So, swap them around to fix SFP 1 and 3 failed to read EEPROM errors.
Fixes: 29b3d929a6 ("microchipsw: lan969x: add Novarq Tactical 1000")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reuse Device/FitImage recipe instead of open coding it and
drop duplicate KERNEL_INITRAMFS recipe for eDPU.
While at it, lets clean up the boot script to drop uneeded console
setting, earlycon etc.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Move the Device/FitImage recipe to the generic image Makefile to avoid
duplicating it for other subtargets.
Will be used for uDPU/eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Use the added support for generating per device targz rootfs so that images
generated for Methode devices when CONFIG_TARGET_MULTI_PROFILE and
CONFIG_TARGET_PER_DEVICE_ROOTFS are set, we actually get the targz rootfs
that respects DEVICE_PACKAGES.
Currently, buildbot generated images have no networking, LM75 nor I2C
working, as the generated images do not include required kmods that are
listed in DEVICE_PACKAGES.
While at it, there is no need for tar to run in verbose mode.
Fixes: 7dff6a8c89 ("mvebu: uDPU: add sysupgrade support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, for targets that use the CONFIG_TARGET_ROOTFS_TARGZ a single
rootfs tarball is generated for the subtarget based of $(TARGET_DIR).
However, this means that it does not respect DEVICE_PACKAGES like other
rootfs images.
So, lets augment CONFIG_TARGET_ROOTFS_TARGZ by adding a proper targz fstype
so that per device rootfs is generated under lock.
This is required so that devices that use custom sysupgrade archives like
Methode devices, can actually include a per device rootfs so when building
for multiple devices and with CONFIG_TARGET_PER_DEVICE_ROOTFS set the built
image actually includes the listed DEVICE_PACKAGES.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Migration of the eDPU DTS to upstream one broke the eDPU plus model
since the required ethernet aliases are missing and U-Boot then cannot
find the required ethernet nodes.
So, after sending the required fix upstream, lets apply it in OpenWrt
as well.
Fixes: 9852dda410 ("mvebu: move DTS diff into a patch for Methode uDPU")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Now that DCB is enabled by default, it makes sense to include it on
lan969x.
While we are here, lets include ip-bridge as these devices are switches
and the Busybox applet does not expose enough functionality.
These devices have no space constraints.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Switchdev driver used by microchipsw supports DCB and has not storage
constraints, so enable kernel and driver DCB support by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Update the DTS to the latest pending upstream version, it looks like this
should get merged soon upstream.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Due to PTP conflicts with CONFIG_ALL_KMODS which causes the end images
to end up with no switchdev driver included, lets switch to using the
switchdev and PHY drivers as modules instead.
Fixes: 88a404a2d1 ("microchipsw: add support for Microchip LAN969x switches")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Microchip ATF depends on Ruby scripts to generate the FWU monitor HTML
and more, so make sure that host Ruby is available.
We also need to call the scripts directly via Ruby executable as shebang
wont work due to lack of Ruby in the Buildbot container.
Fixes: 5205c0c426 ("microchipsw: lan969x: add Microchip EV23X71A")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
LibreSSL 3.9+ has dropped support for X509V3 extension API so cert_create
tool does not compile against it at all.
This was hidden by the fact that it was compiling against OpenSSL on my
host which still has that API, however we do not ship libssl-dev in the
Buildbot containers so compiling against distro OpenSSL is not possible.
So, after a long time trying to find any docs on that API I resorted to
LLM(Gemini 3 Pro) to get it to compile.
Our libcrypto is linked against pthread so we must pass -lpthread as well
for cert_tool.
Fixes: 5205c0c426 ("microchipsw: lan969x: add Microchip EV23X71A")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Now that there is a consumer board available, lets drop source-only so that
buildbots provide official images.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Novarq Tactical 1000 is a LAN9696 based switch.
Specifications:
* CPU: Microchip LAN9696 switch SoC
* DRAM: 2GB DDR4
* Storage:
* 32MB QSPI NOR
* 16GB eMMC
* Networking:
* 24 x 10/100/1000 RJ45 via LAN8804 Quad PHY-s over QSGMII
* 4 x 100/1000/2500/5000/10000 SFP+ ports
* 1 x 10/100/1000 management RJ45 via LAN8840 PHY over RGMII (U-Boot too)
* USB: 1 x USB2.0 Type-A
* Management via USB-C (MCP2200):
* UART @ 115200 baud (Default), 921600 possible
* GPIO-s for bootstrap and reset
* LED-s:
* 2 per networking port (Green and Yellow)
* Green status LED
* Soft reset GPIO
* Power: 12V DC barrel jack
* External PoE:
* Option for PoE add-on
* Temperature Sensors:
* TMP1075 onboard
* CPU temperature
* Microchip MCP79402 RTC with battery back-up
* Microchip ATECC608C secure peripheral
* CPU heatsink with PWM fan
* Onboard header for case fan
Installation instructions:
1. Connect to UART via the USB-C port
2. Connect the management port
3. Boot and interrupt U-Boot
4. TFTP the OpenWrt initramfs image and boot it
5. SCP the OpenWrt eMMC GPT image to a running OpenWrt initramfs to /tmp
openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
And decompress it via:
gzip -d /tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img.gz
6. Wipe eMMC with:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
7. Flash OpenWrt eMMC image with:
dd if=/tmp/openwrt-microchipsw-lan969x-novarq_tactical-1000-squashfs-emmc-gpt.img
of=/dev/mmcblk0
After a restart OpenWrt will boot, and then regular sysupgrade can be used
for upgrades.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Update microchipsw TF-A to the latest bugfix release that fixes
SHA checksum validation if large files are uploaded via the monitor mode.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Microchip EV23X71A is a LAN9696 based EVB.
Specifications:
* CPU: Microchip LAN9696 switch SoC
* DRAM: 1GB DDR4
* Storage:
* 2MB QSPI NOR
* 4GB eMMC
* Networking:
* 24 x 10/100/1000 RJ45 via LAN8814 Quad PHY-s over QSGMII
* 4 x 100/1000/2500/5000/10000 SFP+ ports
* 1 x 10/100/1000 management RJ45 via LAN8840 PHY over RGMII (U-Boot too)
* USB: 1 x USB2.0 Type-A
* Management via USB-C (MCP2200):
* UART @ 115200 baud
* GPIO-s for bootstrap, reset and clock selection
* DIP switch for boostrap configuration
* LED-s:
* 2 per networking port (Green and Yellow)
* Green status LED
* Yellow reset LED
* Hard reset button
* Power:
* 12V DC barrel jack
* 48/56V DC screw terminal
* Selectable via toggle switch
* PTP support:
* Sync-E DPLL ZL30732B to generate the board required clocks
* Two SMAs for PTP and two for Station clock inputs and outputs
* Two ITU-T G.8275-compliant RS-422 interfaces for PTP applications
* External PoE:
* Option for PoE add-on, like EV14Y36A (IEEE 802.3af/at/bt Type 4
standard com-pliant)
* Option for external CPU control via SPI and PCIe
Installation instructions:
1. Connect to UART via the USB-C port
2. Connect the management port
3. Boot and interrupt U-Boot
4. TFTP the OpenWrt initramfs image and boot it
5. SCP the OpenWrt eMMC GPT image to a running OpenWrt initramfs to /tmp
openwrt-microchipsw-lan969x-microchip_ev23x71a-squashfs-emmc-gpt.img.gz
And decompress it via:
gzip -d /tmp/openwrt-microchipsw-lan969x-microchip_ev23x71a-squashfs-emmc-gpt.img.gz
6. Wipe eMMC with:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
7. Flash OpenWrt eMMC image with:
dd if=/tmp/openwrt-microchipsw-lan969x-microchip_ev23x71a-squashfs-emmc-gpt.img
of=/dev/mmcblk0
After a restart OpenWrt will boot, and then regular sysupgrade can be used
for upgrades.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add a new microchipsw target aimed add supporting Microchip switch
SoC-s.
Start by supporting LAN969x SoC-s as the first subtarget.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Import pending PXA I2C recovery fixes so that if I2C recovery is enabled in
the DTS it does not completely break I2C as it currently does since kernel
6.6.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Currently, enabling USB, BT or Netfilter support after initial compilation
will not trigger a rebuild, so add the missing PKG_CONFIG_DEPENDS so
that rebuild gets triggered.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Now that we can pass the desired compression via cmdline, pass ZSTD as the
desired compression algorithm for F2FS.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
F2FS requires the compression algorith to be passed as argument while
mounting, so lets do so for the misc partition.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
In order to prolong the eMMC life and utilize ZSTD compression on Methode
devices, we must format the F2FS rootfs and misc partition with xattr and
compression support feature flags first.
This will only happen if partitions are broken currently, but later
commits will add support to convert existing boards to use compression.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Methode devices require mkfs.f2fs in order to format rootfs and misc
partitions if they have not already been formatted.
fdisk is required if partition table got broke so it can be regenerated.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We would love to utilize ZSTD compression support in F2FS on the
Methode euroDPU so lets enable the required kernel support.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Well, it seems that cryptopp hash was never refreshed since calling
make package/boot/arm-trusted-firmware-mvebu/check FIXUP=1 V=s does not
actually refresh the download calls hashes so refresh it manually.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since ("download: don't overwrite VERSION variable") trying to download the
required sources for mvebu ATF will fail with:
Makefile:247: *** Download/mox-boot-builder is missing the SOURCE_VERSION field.. Stop.
This also broke the buildbot mvebu/cortex-a53 builds.
So, fix it by switching to SOURCE_VERSION instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Lets update to 2024.04 in order to drop all of the patches as they have
been merged upstream.
Tested on Methode eDPU.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
HW specifications:
* Mediatek MT7981A
* 256MB SPI-NAND
* 512MB DRAM
* Uplink: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 with 802.3at
PoE (Built-in GBe PHY)
* LAN: 1 x 10/100/1000Base-T Ethernet, Auto MDIX, RJ-45 (Airoha EN8801SC)
* 1 Tricolor LED
* Reset button
* 12V/2.0A DC input
Installation:
Board comes with OpenWifi/TIP which is OpenWrt based, so sysupgrade can
be used directly over SSH.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Airoha EN8801SC PHY is a gigabit PHY used on Edgecore EAP111 so, include
the MTK driver with some cleanups.
Unfortunatelly, there is no specification sheet nor datasheet available
in order to demistify the magic PBUS writes and work on upstreaming
this driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Since kernel 5.11, the PXA I2C driver has been converted to generic I2C
recovery, which makes the I2C bus completely lock up if recovery pinctrl
is present in the DT and I2C recovery is enabled.
This effectively completely broke I2C on Methode uDPU and eDPU boards
as both of them rely on I2C recovery.
After a discussion upstream, it was concluded that there is no simple fix
and that the blamed upstream commit:
0b01392c18b9993a584f36ace1d61118772ad0ca ("i2c: pxa: move to generic GPIO
recovery") should be reverted.
I have sent the revert upstream, it should be merged soon so lets "fix"
OpenWrt as well.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
The same image can be used on both versions as U-Boot will enable the
switch node and disable the unused ethernet controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of eDPU uses an Marvell MV88E6361 switch to connect the SFP
cage and G.hn IC instead of connecting them directly to the ethernet
controllers.
In order to use the same image for both boards, U-Boot is responsible for
detecting the revision and enabling/disabling DTS nodes.
So, to make it easy for users, lets add the pending U-Boot patches to build
in OpenWrt.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
New revision of Methode eDPU boards uses Marvell 88E6361 switch, so lets
backport it from kernel 6.5.
Since 5.15 doesnt have phylink_get_caps I had to modify the backport to
use the old mv88e6393x_phylink_validate instead.
I had to fixup one more instance of port_max_speed_mode as well that is not
present in 6.5.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
We have to move to use git clone as there are no newer tagged releases.
Changes:
604f8f5 Default CROSS_CM3 to arm-none-eabi- instead of armv7m-softfloat-eabi-
b9b9419 Tidy up license information
0290b2c wtmi: Fix typo
a10b8e9 Makefile: fix a53-firmware.bin generation (maximum size is not optimal)
f654082 wtmi: Add const qualifier to isr_vector
4a43a3b wtmi: Improve detection of ESPRESSObin boards with Topaz
189e629 wtmi: Improve detection of boards with insufficient MDIO pull-up
3dac4fe wtmi: Fix detection of Armada 3720 Devel Board
3ca4dfa Bump mox-imager commit
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
1de442d Convert floating point operations to integer operations
ce6770d Modify mv_ddr4_calibration_validate function body to match function header
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Changes:
a3e1c67 wtmi: Fix linker output sections
f65e3bf wtmi: Remove usage of non-existant string.h file and memcpy() function
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Recent envtools update to 2023.07.02 has introduced a breakage when trying
to parallel build with the following error:
/bin/sh: line 1: scripts/basic/fixdep: No such file or directory
Luckily it can easily be reproduced locally via a simple script so it was
not hard to bisect it down to upstream commit [1].
However, its not that commits fault, it just uncovered an issue with the
way we have been building envtools for a long time, maybe even from the
package introduction.
The issue is that we are trying to build envtools as one of the U-Boot
no-dot-config-targets but envtools was newer a valid target for it but
since we were creating the config headers that were not actually used it
was actually building all this time.
Since the blamed commit [1] a tool called printinitialenv is built and
now a proper config is actually required in order for prerequisites to
get built properly.
So, in order to properly fix this (Hopefully for good) lets stop pretending
that envtools are a valid no-dot-config-targets target and use the
tools-only defconfig which is meant exactly for just building the tools.
This will make a minimal config for the U-Boot sandbox target and then
envtools will build just fine in parallel mode (I tested with 32 threads).
We do hovewer need to override the ARCH passed by OpenWrt and set it to
sandbox as otherwise U-Boot will not find the required headers because the
ARCH is being overriden to an incorrect one.
[1] https://source.denx.de/u-boot/u-boot/-/commit/40b77f2a3ac13a7547c1b7c9c51a4090869de8f4
Fixes: 9db0330052 ("uboot-envtools: update to 2023.07.02")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
CONFIG_FRAME_WARN is set dynamically, so there is no need for it to be set
in target kernel configs, so lets remove it from all configs.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
CONFIG_FRAME_WARN value is set by config/Config-kernel.in based on the
target type dynamically since commit:
16a2051 ("kernel: Set CONFIG_FRAME_WARN depending on target").
However, CONFIG_FRAME_WARN was not set to get filtered out so it ended up
in multiple target configs during refreshes.
So, lets filter out CONFIG_FRAME_WARN as its set dynamically to prevent it
ending up in more target configs.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Adds support for the Wallys DR40x9 series boards.
They come in IPQ4019 and IPQ4029 versions.
IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures.
Specifications are:
* CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz
* RAM: 512 MB
* Storage: 2MB of SPI-NOR, 128 MB of parallel NAND
* USB 3.0 TypeA port for users
* MiniPCI-E with PCI-E 2.0 link
* MiniPCI-E for LTE modems with only USB2.0 link
* 2 SIM card slots that are selected via GPIO11
* MicroSD card slot
* Ethernet: 2x GBe with 24~48V passive POE
* SFP port (Does not work, I2C and GPIO's not connected on hardware)
* DC Jack
* UART header
* WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac
* 4x MMCX connectors for WLAN
* Reset button
* 8x LED-s
Installation instructions:
Connect to UART, pins are like this:
-> 3.3V | TX | RX | GND
Settings are 115200 8n1
Boot initramfs from TFTP:
tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb
bootm
Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name>
The board file binary was provided from Wallystech on March 14th 2023
including full permission to use and distribute.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Armada 7040 uses a rather small 15MB memory window for every PCI adapter,
however this is not sufficient for Qualcomm QCA6390 802.11ax cards that
are shipped along with the OpenWrt WLAN model of MOCHAbin as ath11k
requires at least 16MB of memory.
So, similar to what MACCHIATOBin has been doing for years, lets move
to using the second PCIe 2 memory window and expand it to 128MB to
make it future proof.
This has been already sent upstream [1].
[1] https://lore.kernel.org/linux-arm-kernel/20230219121418.1395401-1-robert.marko@sartura.hr/
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Provide ATF support for Methode eDPU as well, this makes it easy for
OpenWrt users to update the included U-boot+ATF combo.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Add support for building for Methode eDPU board, no patches are needed
as board has been upstreamed and is part of the 2022.10-rc releases.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Update mvebu U-boot to 2022.10 to avoid backporting patches in order
to support Methode eDPU.
It also allows dropping existing patches as they are all backports.
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs
Tested-by: Russell Morris <github@rkmorris.us> # espressobin-v3-v5-1gb-1cs
Tested-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Turris Omnia]
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Remove networking configs for non DSA converted boards in ipq40xx.
Currently, they are just causing clutter.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Robert Marko