f5d17dd60a89 mstp: add default Hello Time constant
17c36bebada1 mstp: use default Hello Time in recordTimes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for the TP-Link EAP683-LR, an AX6000 Ceiling Mount WiFi 6
AP.
Hardware:
* SoC: MediaTek MT7896AV
* RAM: 1GiB DDR4 (Samsung K4A8G165WC-BCTD)
* Flash: 128MiB SPI-NAND (ESMT F50L1G41LB)
* Ethernet: 1x 10/100/1000/2500 Mbps PoE-PD (MaxLinear GPY211C)
* WiFi: MT7976AN/MT7976GN 2.4/5GHz 4T4R
* LEDS: 3x blue connected to a single GPIO line
* Buttons: 1x reset
* BLE/Thread/Zigbee: CC2652
Stock firmware uses a random MAC address for ethernet, label MAC for
2.4 and label MAC + for 5GHz.
Installation via bootloader:
* Solder JST??? connector on J255, alternatively solder wires on the
TP13-TP15 pads. Pinout: TP13: TX, TP14: RX, TP15: GND, TP16: VCC.
The pins for J255 are in the same order.
* Interrupt boot process by repeatedly pressing Ctrl+b during boot
* In the boot menu, select U-Boot console
* Ensure the U-Boot environment variable "tp_boot_idx" is not set:
# setenv tp_boot_idx
# saveenv
* Boot the OpenWrt initramfs:
# tftpboot openwrt-mediatek-filogic-tplink_eap683-lr-initramfs-kernel.bin
# bootm
* copy openwrt-mediatek-filogic-tplink_eap683-lr-squashfs-sysupgrade.bin
to /tmp and install it using sysupgrade
Flashing via OEM firmware is currently not supported. The
tplink-safeloader utility does not recognize the OEM firmware:
DEBUG: can not find fwuphdr
Firmware image partitions:
base size name
Segmentation fault (core dumped)
To revert to the OEM firmware, you can set the U-Boot environment
variable "tp_boot_idx" to 1 via bootloader, or using fw_setenv via
OpenWrt. This should result in booting from the ubi1 partition, which
OpenWrt should not touch. Then use the web interface to upgrade
firmware: System > Firmware Update.
The OEM firmware uses 0x800000 for the runtime_backup partition size.
This causes the following warning:
mtd: partition "runtime_backup" extends beyond the end of device "nmbm_spim_nand" -- size truncated to 0x600000
This is due to the NMBM reserved blocks. Use 0x600000 in our DTS.
Thanks to init Lab's user890104, who soldered jumper wires on the TTL
pads for me so I could have serial console. My soldering skills just
aren't good enough to pull that off without risk damaging things.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for the Edgecore ECS4100-12PH, an 8-port 802.3bt PoE Gigabit
Ethernet switch with 2 combo RJ45/SFP and 2 SFP ports.
Hardware:
* SoC: RTL8393M
* RAM: 256MiB
* Flash: 32MiB SPI-NOR
* Ethernet:
* 8x GbE RJ45 PoE (external RTL8218B)
* 2x GbE RJ45 / SFP combo (external RTL8214FC)
* 2x SFP (external RTL8214FC)
* Console: RJ45 RS232 port on front panel
* PoE: Nuvoton M0516 + 2x Broadcom BCM59121 PSE
Installation via bootloader:
* open serial console (baud rate 115200)
* interrupt boot process by pressing any key during boot
* boot the OpenWrt initramfs:
# rtk network on
# tftpboot 0x8f000000 /tftpboot/openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-initramfs-kernel.bin
# bootm
* copy openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-squashfs-sysupgrade.bin
to /tmp and use sysupgrade to install it:
# sysupgrade /tmp/openwrt-realtek-rtl839x-edgecore_ecs4100-12ph-squashfs-sysupgrade.bin
Even though U-Boot claims the switch is based on the RTL8392M SoC, my
device is based on the RTL8393M SoC. I have confirmed this by removing
the heatsink, and the Linux kernel agrees with this. Therefore the DTS
has the rtl8393_ prefix.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
KERNEL_ARM64_CONTPTE depends on KERNEL_ARM64 which does not exist. Fix
it by depending on aarch64 instead.
Fixes: e9799d2dd4 ("kernel: add KERNEL_ARM64_CONTPTE")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fixes the following build problem on systems with Python 3.12 or 3.13:
Checking 'python3-setuptools'... failed.
Checking 'swig'... ok.
u-boot: Please install the Python3 setuptools module
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Commit d7e82c78d7 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7 ("generic: backport Realtek PHY patches from upstream")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
ATF supports rk3588 since version 2.12, so let's enable it in
arm-trusted-firmware-rockchip.
We still need the TPL to initialize RAM, but keeping rk3588 in rkbin
would cause a duplicate package name, so rename rk3588 to rk3588-tpl in
rkbin.
Finally, point uboot-rockchip for rk3588 to bl31 built by this package,
and add a dependency on the new trusted-firmware-a-rk3588-tpl pacakge.
While this doesn't necessarily add features, we now no longer rely on
the rk3588_bl31_v1.45.elf blob provided by Rockchip, which is always a
good thing.
Tested on Radxa ROCK 5B+.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
And remove no-warn-rwx-segments hack, as this is no longer needed and
actually causes build to fail. See also commit c117d7a37a
("include/trusted-firmware-a.mk: remove the no-warn-rwx-segments hack").
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
TF-A LTS releases have an lts- prefix in their version tag. Introduce a
PKG_LTS variable to support these.
As the non-LTS tarbals do not contain the version prefix in the
directory, we need different PKG_BUILD_DIR for each variant:
➜ tar --list --file dl/trusted-firmware-a-v2.12.tar.gz | head -n1
trusted-firmware-a-2.12/
➜ tar --list --file dl/trusted-firmware-a-lts-v2.12.1.tar.gz | head -n1
trusted-firmware-a-lts-v2.12.1/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The snapshot builds for qoriq only contain ext4 images. Add squashfs to
FEATURES to also have the buildbots build squashfs images.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Dropping the source-only flag from qoriq and adding it to the buildbots
exposed a missing kernel config symbol: CONFIG_DRM_OFDRM. Addd it as
disabled to the qoriq kernel config, as the only device currently
supported in the qoriq target does not have any display hardware.
Reported-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
While the qoriq target currently supports only one device, the
WatchGuard Firebox M300, the feedback from people using it is that it's
a great bang for the buck. Additionally, people suggest having no
snapshots available hurts adoption.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Enabling KERNEL_DEBUG_INFO_BTF and KERNEL_KPROBE_EVENTS on 6.6 exposes
CONFIG_PROBE_EVENTS_BTF_ARGS in the kernel config. Add a build option
for it to fix build failures with KERNEL_DEBUG_INFO_BTF and
KERNEL_KPROBE_EVENTS enabled on targets using the 6.6 kernel.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Fixes the following error:
Syntax error: Unable to resolve path for module 'uci'
In line 3, byte 27:
`import * as uci from 'uci';`
Near here ----------------^
Fixes: 4a3ed518b2 ("wifi-scripts: rewrite wifi detect code in ucode")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
According to the Realtek SDK code, the RTL8214FC, RTL8218B and RTL8218FB
all have the same chip ID 0x6276. Let's add a constant for it, as we're
using it in more than one location.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Respect the phy-is-integrated property on ethernet-phy nodes.
There are RTL8393M switches where the PHYs at address 48 and 49 are
provided by an external RTL8214FC. Hardcoding them to use the internal
SerDes makes it impossible to use the ports connected to such an
external PHY. Respect the phy-is-integrated property on ethernet-phy
nodes as a first step to support such ports.
The potential impact for this should be limited to RTL8393 based
switches, and looking at the commit messages and device tree files of
the supported switches based on this SoC, the SFP and/or combo ports are
either not working (D-Link DGS-1210-52, Netgear GS750E, TP-Link
SG2452P/T1600G-52PS), use PHYs at a different address (Panasonic
SwitchM48EG PN28480K), or already have the phy-is-integrated property
set on the PHYs at address 48 and 49.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
The backports introduced in commit d40756563c ("kernel: backport
phylink changes from mainline Linux") broke the mv88e6xxx DSA driver.
A backport to fix this was added to the kirkwood target, but as it is
used in multiple targets, and there's a kmod package for it, the fix
should be in generic backports.
This fixes the switch on the WatchGuard Firebox M300 when running the
6.1 testing kernel.
There is no need to backport the fix for the 6.6 kernel, as it was
included in 6.6.5.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Building perf's intel-pt-decoder fails on both PPC32 and PPC64:
/home/stijn/Development/OpenWrt/openwrt/staging_dir/toolchain-powerpc64_e5500_gcc-13.2.0_musl/lib/gcc/powerpc64-openwrt-linux-musl/13.2.0/../../../../powerpc64-openwrt-linux-musl/bin/ld.bfd:
/home/stijn/Development/OpenWrt/openwrt/build_dir/target-powerpc64_e5500_musl/linux-qoriq_generic/linux-6.1.86/tools/
perf-target-powerpc64_e5500_musl/perf-in.o: in function `insn_set_byte':
/home/stijn/Development/OpenWrt/openwrt/build_dir/target-powerpc64_e5500_musl/linux-qoriq_generic/linux-6.1.86/tools/perf/util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:64:
undefined reference to `__le32_to_cpu'
Add NO_AUXTRACE=1 to MAKE_FLAGS for LINUX_KARCH powerpc, which disables
build of intel-pt-decoder on both PPC32 and PPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add support for kernel 6.1 as testing kernel for qoriq. Refresh config
using `make kernel_oldconfig`.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The function introduced in commit 7cbfe5654d is named
filter_port_list_reverse, not filter_port_list_reversed.
Fixes the following error on hpe,1920-8g-poe-65w and
hpe,1920-8g-poe-180w.
/bin/board_detect: /etc/board.d/02_network: line 84: filter_port_list_reversed: not found
Fixes: 7cbfe5654d ("realtek: move port filtering out of uci_set_poe()")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Sander Vanheule <sander@svanheule.net>
Commit e978072baaca ("Do prune_association only after the STA is
authorized") causes issues when an STA roams from one interface to
another interface on the same PHY. The mt7915 driver is not able to
handle this properly. While the commits fixes a DoS, there are other
devices and drivers with the same limitation, so revert to the orginal
behavior for now, until we have a better solution in place.
Fixes: #13156
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When building xdp-tools with CONFIG_USE_LLVM_HOST=y, on a host that
enabled stack protector by default in Clang, compilation fails with the
following error:
CLANG xdp-dispatcher.o
clang-16: error: ignoring '-fstack-protector-strong' option as it is not currently supported for target 'bpfeb' [-Werror,-Woption-ignored]
Add -fno-stack-protector to BPF_CFLAGS to fix this.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add an UCI option to enable Multiple BSSID Advertisement. Enabling this
will announce all BSSIDS on a phy in a single beacon frame. The
interface that is brought up first will be the transmitting profile, all
others are non-transmitting profiles and will be advertised in the
Multiple BSSID element in Beacon and Probe Response frames of the first
interface.
This depends on driver and client support. Enabling this will result in
all but the first interface not being visible at all for clients that do
not support it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use latest release build instead of a git snapshot. As this tarball
extracts in a trusted-firmware-a-2.8 subdirectory, we no longer need to
override the PKG_NAME defined in trusted-firmware-a.mk. The actual
package name is still the same, so we don't need to update any
dependencies.
Tested on A64-OLinuXino-1Ge16GW.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is the newest release where 210-sunxi-deactivate-binman.patch still
applies.
Tested on A64-Olinuxino-eMMC.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Without the default value this still causes a missing symbol. Disable by
default as it depends on FUNCTION_ERROR_INJECTION, which is disabled in
the generic config and we don't have a build symbol to enable that.
Fixes: 500c37c56f ("kernel: add missing symbol")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We currently have build options to customize the IP address used in the
preinit phase of the boot process, but not to set the default LAN IP.
Introduce a boolean build option that, when enabled, results in the IP
address configured for the preinit phase, to be also used as the default
LAN IP address.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The testing kernel has been available since early 2022, and is running
fine for several people. Let's switch to it by default.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Karl Palsson <karlp@etactica.com>
Tested-by: Jan-Niklas Burfeind <openwrt@aiyionpri.me>
While switching qoriq to kernel 5.15, the config for kernel 5.10 was
left behind. Drop it.
Fixes: 230f2fccd1 ("qoriq: switch to kernel 5.15")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This should have been amended in the previous commit.
Fixes: 65e72f8e38 ("github: add issue template")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add an issue template with required fields, instructions how to easily
get some of that required data from the device. Aside from that, also
add some links to the OpenWrt contact page, and for feature requests,
link to the forum.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
There are 2 different CPE IDs on the NVD website:
cpe:/a:arm:trusted_firmware-a
cpe:/o:arm:arm_trusted_firmware
The ID as currently used in trusted-firmware-a.mk does not exist. The
CPE ID using the arm_trusted_firmware product name only lists a few
records for versions 2.2 and 2.3 on the NVD site. The CPE ID using the
trusted_firmware-a product name lists many more records, and actually
has a CVE linked to it. Therefore, use the CPE ID using the
trusted_firmware-a product name.
Fixes: 104d60fe94 ("trusted-firmware-a.mk: add PKG_CPE_ID")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Both mirrors provided in the Makefile only serve gzipped tarballs.
Fixes: #10871
Fixes: 9edfe7dd13 ("source: Switch to xz for packages and tools where possible")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.10.158 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 6801c460b6 ("kernel: bump 5.10 to 5.10.158")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.15.82 added a prompt for the FUNCTION_ERROR_INJECTION symbol.
This is exposed in builds with CONFIG_KERNEL_KPROBES enabled, causing
those builds to fail due to a missing symbol. Add the symbol to fix
this.
Fixes: 68426e54ed ("kernel: bump 5.15 to 5.15.82")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The testing kernel has been running fine for months on a rather complex
network setup, with one exception being a crash in
__xfrm_state_delete(). This crash has been fixed in kernel 5.15.82, so
let's switch the qoriq target to kernel 5.15 by default.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When the v1 and v2 variants of the U6LR were introduced, the board
network config was not adapted to the new device names. Due to this, the
wrong network config is applied during initial boot. The resulting
config has lan, wan and a switch, while this device only has a single
ethernet interface without a switch.
Fix this by using a wildcard that matches all the variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Fixes: 5c8d3893a7 ("mediatek: new target ubnt_unifi-6-lr-v1-ubootmod")
Fixes: 31d86a1a11 ("mediatek: add Ubiquiti UniFi 6 LR v2 targets")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Daniel Golle <daniel@makrotopia.org>
There is no WLAN_STA_MBO flag, but according to the hostapd source code,
when an STA does not support MBO, cell_capa will be 0. Use this to
indicate MBO support in the get_clients ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: David Bauer <mail@david-bauer.net>
There is only one module in kmod-sched that depends on iptables. Move it
to its own kmod package so we can drop the kmod-ipt-core dependency from
kmod-sched. This makes it possible to disable all kmod-ipt-* packages
without having to disable kmod-sched. Since we now default to firewall4
and nftables, we should avoid iptables dependencies where we can.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Enable PowerPC Book-E Watchdog Timer support. Having this enabled
in-kernel will result in procd starting it during boot.
This effectively solves the problem of the WDT in the Winbond W83793 chip
potentially resetting the system during sysupgrade, which could result
in an unbootable device. While the driver is modular, resulting in procd
not starting the WDT during boot (because that happens before kmod
load), the WDT handover during sysupgrade results in the WDT being
started. This normally shouldn't be a problem, but the W83793 WDT does
not like procd's defaults, nor the handover happening during sysupgrade.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The random crashes observed with HARDENED_USERCOPY enabled no longer
seem to occur. Enable HARDENED_USERCOPY to improve security.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.15.49 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.15 config.
Fixes: f1cd144482 ("kernel: bump 5.15 to 5.15.49")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Kernel 5.10.124 introduced a new symbol 'LIB_MEMNEQ'. Add it to the
generic 5.10 config.
Fixes: 9e5d743422 ("kernel: bump 5.10 to 5.10.124")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Enabling mbo by default on 802.11ax devices breaks for encryption types
that do not enable 802.11w by default. Disable mbo by default to fix
this. Enabling mbo by default on 802.11ax devices was not explained in
the commit message anyway.
Fixes: 6eee983656 ("hostapd: introduce mbo option")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Introduce a new option background_radar to toggle hostapd's background
radar feature. Enabling this allows DFS CAC to run on dedicated radio RF
chains while the radio(s) are otherwise running normal AP activities on
other channels.
As OpenWrt configures hostapd to use a channel list even when a single
channel is configured, using this feature requires a list of channels in
/etc/config/wireless. Alternatively, channel can be set to auto.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Support the use of MBO in the bss_transition_request ubus method.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Introduce a new option mbo to toggle Multi Band Operation aka Agile
Multiband for a BSS.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Multi Band Operation is required for 802.11ax certification, so let's
enable it if 802.11ax support is enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Multi Band Operation aka Agile Multiband introduces new Transition
and Transition Rejection Reason Codes that should improve client
steering. Add a config symbol to enable it, and enable it by default for
the full variants.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Document the ubus methods we added to hostapd so that people don't have
to read code to figure out which methods are available and what they do.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
11f5c7b fw4.uc: fix zone helper assignment
b9d35ff fw4.uc: don't skip zone for unavailable helper
e35e26b tests: add test for zone helpers
a063317 ruleset: fix conntrack helpers
e1cb763 ruleset: reuse zone-jump.uc template for notrack and helper chain jumps
11410b8 ruleset: reorder declarations & output tweaks
880dd31 fw4: fix skipping invalid IPv6 ipset entries
5994466 fw4: simplify `is_loopback_dev()`
53886e5 fw4: fix crash in parse_cthelper() if no helpers are present
11256ff fw4: add support for configurable includes
3b5a033 tests: add test coverage for firewall includes
d79911c fw4: support sets with timeout capability but without default expiry
15c3831 fw4: add support for `option log` in rule and redirect sections
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This requires U-Boot environment changes:
setenv OpenWrt_kernel watchguard_firebox-m300-fit-uImage.itb
setenv loadaddr 0x20000000
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; mmc dev 0; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr'
Trying to sysupgrade an image containing this change on an M300 already
running OpenWrt will fail with the following error:
Tue Jun 14 12:06:21 EEST 2022 upgrade: The device is supported, but the config is incompatible to the new image (1.0->1.1). Please upgrade without keeping config (sysupgrade -n).
Tue Jun 14 12:06:21 EEST 2022 upgrade: Kernel switched to FIT uImage. Update U-Boot environment.
Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from bootdisk...
Tue Jun 14 12:06:21 EEST 2022 upgrade: Extract boot sector from the image
Tue Jun 14 12:06:21 EEST 2022 upgrade: Reading partition table from image...
Image check failed.
This is to prevent rendering your device unbootable. Make the U-Boot
environment changes as instruced above, and then flash the image using
sysupgrade -F. The config can be kept, there is no need to use -n.
After the new image booted successfully, you can increase the compat_version:
uci set system.@system[0].compat_version='1.1'
uci commit
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the KERNEL_SUFFIX variable in Build/sdcard-img, rather than
using hardcoded "-kernel.bin", to allow overriding KERNEL_SUFFIX for a
device.
Fixes: 080a769b4d ("qoriq: new target")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
902b321 wireless-regdb: Update regulatory rules for Israel (IL)
20f6f34 wireless-regdb: add missing spaces for US S1G rules
25652b6 wireless-regdb: Update regulatory rules for Australia (AU)
081873f wireless-regdb: update regulatory database based on preceding changes
166fbdd wireless-regdb: add db files missing from previous commit
e3f03f9 Regulatory update for 6 GHz operation in Canada (CA)
888da5f Regulatory update for 6 GHz operation in United States (US)
647bcaa Regulatory update for 6 GHz operation in FI
c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz
2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules
7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries
68a8f2f wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7e06706 iw: event: report missing radar events
5909e73 iw: survey: add support for radio stats
64bf570 update nl80211.h
0900996 iw: print Radar background capability if supported
56c6077 iw: print out assoc comeback event
a4e5418 iw: support 160MHz frequency command for 6GHz band
5a71b72 iw: Print local EHT capabilities
e3287a1 station: print EHT rate information
ff67fb2 iw: fix double tab in mesh path header
05a5267 iw: fix 'upto' -> 'up to'
00a2985 iw: handle VHT extended NSS
82e0bd1 update nl80211.h
c95877c info: add missing extended features
0976378 info: refactor extended features
79f20cb bump version to 5.19
Sync nl80211.h with our version of mac80211 and remove parts of the iw
code that are not supported by our version of mac80211.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
All known users of this ubus method have been updated to use the new
bss_transition_request method instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Using nvmem-cells to set the MAC address for a DBDC device results in
both PHY devices using the same MAC address. This in turn will result in
multiple BSSes using the same BSSID, which can cause various problems.
Use the hotplug script for the EAP615-Wall instead to avoid this.
Fixes: a1b8a4d7b3 ("ramips: support TP-Link EAP615-Wall")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
This is only effective for host build of normal packages, not tools.
Fixes: ad79b92719 ("elfutils: move host build to tools")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Building all of the components results in strip being installed in
staging_dir/host/bin. This strip binary will take precedence over
binutils strip that is installed in the toolchain directory.
This will not work on host systems that do not have libdw installed, as
we do not set HOST_LDFLAGS to override rpath to staging_dir/host/lib.
However, rather than overriding rpath, we should just avoid using
elfutils strip entirely.
Override the SUBDIRS variable in the Makefile to only build and install
the libraries we require for dwarves and frr.
Fixes the following build failure in toolchain/gdb:
strip: error while loading shared libraries: libdw.so.1: cannot open shared object file: No such file or directory
Fixes: ad79b92719 ("elfutils: move host build to tools")
Reported-by: Dominick Grift <dominick.grift@defensec.nl>
Reported-by: Lucian Cristian <lucian.cristian@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Some buildbots fail to build elfutils due to m4 being missing. Add m4 as
a dependency for elfutils to fix this.
Fixes: ad79b92719 ("elfutils: move host build to tools")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This is required to use BPF maps of type BPF_MAP_TYPE_PERF_EVENT_ARRAY
for sending data from BPF programs to user-space for post-processing
or logging.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Add DEBUG_INFO_REDUCED as a kernel config option and remove it from the
kernel configs. This is in preparation of the upcoming option to enable
BTF typeinfo, which is incompatible with DEBUG_INFO_REDUCED.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
We currently enable DEBUG_INFO_REDUCED for all targets via the generic
kernel config. There is only one subtarget, layerscape/armv8_64b, that
overrides this setting. As there is no explanation for this in the
commit message that introduced this, and question to its author went
unanswered, let's simply drop this symbol from the subtarget config.
This way, we have consistency across the tree, and we do not have to
introduce a special case when moving this symbol to an OpenWrt kernel
config option.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Building tools/resolve_btfids requires libelf and zlib. Without this
build fix, the kernel build system will not find these dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
According to the GNU make manual, specifying library paths should be
done in LDFLAGS rather than LDLIBS. Replace KBUILD_HOSTLDLIBS with
KBUILD_HOSTLDFLAGS to pass the host lib directory.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
HOST_LOADLIBES was renamed to KBUILD_HOSTLDLIBS in kernel 4.19. As the
oldest kernel version we support is 5.10, cleanup HOST_LOADLIBES use.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
HOST_LOADLIBES was renamed to KBUILD_HOSTLDLIBS in kernel 4.19. As the
oldest kernel version we support is 5.10, cleanup HOST_LOADLIBES use.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The upcoming dwarves host package requires elfutils. As dependencies for
tools must exist in tools, we need to move elfutils host build there.
As there is at least one package that depends on this, and there is no
proper way to create such dependency in the build system, build it
unconditionally when not building on macOS.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This symbol is added by the bcm27xx target patches so it should depend
on that target.
Fixes: efd9463dcf ("kernel: add missing symbol for bcm27xx")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
When KERNEL_PERF_EVENTS is enabled in OpenWrt, the RPI_AXIPERF symbol is
exposed. Add a build option for it to fix build failures with
KERNEL_PERF_EVENTS enabled.
Fixes: 20ea6adbf1 ("bcm27xx: add support for linux v5.15")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The WatchGuard Firebox M200 and M300 use a Marvell 88e1543 PHY for the
first 3 ethernet ports. This PHY is supported by the Marvell Alaska PHY
driver, so enable it.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
There are various reports on Github and in the forum that this commit
causes multiple problems.
This reverts commit ee6ba216d8.
Fixes: #9420
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The memory leak is fixed by the kernel patches backported in the
previous commit.
This reverts commit 1fa8780056.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Enabling KERNEL_KPROBES exposes KERNEL_BPF_KPROBE_OVERRIDE. Add a build
option for it to fix build failures with KERNEL_KPROBES enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Stijn Tintel