Enable the busybox feature to save shell command history.
(.apk size increase 0.5 kB)
To prevent flash wear,
* save history only at the exit from a shell session, and
* set /tmp as the default location for the history file. The history
is kept on ramdisk until a reboot, when the history is then lost.
If the user wants to save history onto flash, he can change the location
definition in /etc/profile.d/busybox-history-file.sh
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/17179
cherry picked from commit e23b37b2d9)
[ fix conflict error ]
Signed-off-by: Andrey Zotikov <andrey.zotikov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following security isseus with CVE numbers:
CVE-2026-55614: GHSA-mcfg-c4r7-pjpf — case-sensitive Transfer-Encoding matching
CVE-2026-55612: GHSA-p55c-rmhc-qfm5 — invalid chunk-length state reset
CVE-2026-55613: GHSA-wgwp-64hh-f52p — ubus POST body parse-error desync
The branch also carries hardening with no CVE: one-byte overflow in
uh_urldecode, off-by-one OOB read in uh_b64decode, constant-time
password compare, $p$ crypt-hash handling.
Link: https://github.com/openwrt/openwrt/pull/24259
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cherry pick the patches recommended in the hostapd security advisory
2026-1:
https://w1.fi/security/2026-1/missing-ml-parsing-validation.txt
Vulnerability
Vulnerabilities in parsing and use of received multi-link (MLO/EHT/IEEE
802.11be/Wi-Fi 7) information has been identified in hostapd and
wpa_supplicant. These issues show up in various cases where frames
including information on affiliated links are parsed and processed in
both AP and STA modes. The issues can result in process termination due
to buffer read overflow checks and memory corruption.
The issues for AP mode (hostapd or wpa_supplicant) can result in
denial-of-service attacks due to process termination and small memory
corruption that could theoretically cause other issues, but it does not
seem likely that those could be exploiting in practice. Affected areas
can be reached by sending invalid Management frames without needing
authentication or user action on the target device.
Link: https://github.com/openwrt/openwrt/pull/24043
(cherry picked from commit 8614a2ba68)
[Removed 004, 0005 and 008 which do not apply and fix some others]
Link: https://github.com/openwrt/openwrt/pull/24295
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CMake fails to bootstrap its host tool with GCC 16:
cmake.o: undefined reference to
`cmGlobalGhsMultiGenerator::cmGlobalGhsMultiGenerator(cmake*)'
Source/cmake.cxx includes cmGlobalGhsMultiGenerator.h guarded only by
__linux__, not by CMAKE_BOOTSTRAP. The NewFactory() call is compiled out
during bootstrap, but GCC 16 devirtualization still emits the uncalled
inline NewFactory() and the cmGlobalGeneratorSimpleFactory<> template,
which reference symbols only defined in cmGlobalGhsMultiGenerator.cxx, a
file that is not compiled during bootstrap.
Backport the upstream fix, which moves the include behind the existing
CMAKE_BOOTSTRAP guard. It is in no 3.30.x release (that branch is EOL);
upstream shipped it first in 3.31.10 / 4.0.5 / 4.1.2.
Assisted-by: Claude:claude-opus-4-8
Link: https://github.com/openwrt/openwrt/pull/24303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch backports a small but important part of the upstream commit:
b3f1b9e2aa07 build: Remove INCLUDE_MEMORY [PR117737]
Its original commit message fails to mention that the commit also moves
the `#include <memory>` to an earlier position within system.h,
which is the actual change that we're after in this patch.
Building our GCC 14.3 with host GCC 16, the inclusion order starts to matter,
which is an issue that was also touched upon by the upstream commits:
9970b576b7e4 Include safe-ctype.h after C++ standard headers, to avoid over-poisoning
f6e00226a4ca build: Move sstream include above safe-ctype.h {PR117771]
Signed-off-by: Lars Gierth <larsg@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/23095
Signed-off-by: Robert Marko <robimarko@gmail.com>
[hauke: Add GCC 13 too]
(cherry picked from commit a32a367259)
Link: https://github.com/openwrt/openwrt/pull/24302
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit migrates the repository validation to a webhook-based bot instead of the GitHub Actions workflow (.github/workflows/formal.yml).
Since the bot handles stable branch labeling automatically (via the "branch_labeling: true" configuration option), the redundant branch check and labeling steps are removed from .github/workflows/labeler.yml.
The following configuration choices are applied in formalities.json:
- check_space_after_assignment: false (Disabled temporarily to catch any issues since it is a newly implemented check)
- check_makefile_indentation: false (Disabled temporarily to catch any issues since it is a new feature)
- check_patch_headers: 'warning' (Changed to warning instead of hard error since many legacy patches lack headers)
- enable_stale_bot: false (Disabled for now)
Other configurations can be adjusted in formalities.json based on the openwrt-bot-worker repository [1].
[1] https://github.com/openwrt/openwrt-bot-worker
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/24256
(cherry picked from commit 9146f931b6)
Link: https://github.com/openwrt/openwrt/pull/24319
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Run this only when a PR is created, so either author or anyone who can
edit the PR message (all maintainers) can trigger such build.
Instead of maintaining it in the main repository, move it to the
external repository to bloat this repository less with further CI
commits.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 8cff0d8ca0)
Link: https://github.com/openwrt/openwrt/pull/24319
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Change-log since version 2026.03.18, retrieved from the wireless-regdb mailing lists:
wireless-regdb: update regulatory database based on preceding changes
wireless-regdb: Update regulatory info for Brunei Darussalam (BN) for 2022
wireless-regdb: allow 320MHz channel width for Russia
wireless-regdb: Update 6 GHz rules for Hong Kong (HK)
wireless-regdb: Update 5/6 GHz power rules for Russia (RU)
wireless-regdb: Fix 60 GHz power unit for Ukraine (UA)
wireless-regdb: Update 6 GHz rules for South Africa (ZA)
wireless-regdb: Update 6 GHz rules for South Korea (KR)
wireless-regdb: Update regulatory rules for Sri Lanka (LK)
wireless-regdb: Add regulatory info for CEPT countries FO, GI, IM, SM and VA listed by WiFi Alliance
Signed-off-by: Hafiz Zafran <hfzz7@duck.com>
Link: https://github.com/openwrt/openwrt/pull/23594
(cherry picked from commit 848c54b5f4)
Link: https://github.com/openwrt/openwrt/pull/24301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
handle_send_a() computed the SRP "A" parameter length as
len = ntohl(msg->len) - sizeof(struct ead_msg_number);
sizeof(struct ead_msg_number) is 1, and the subtraction is evaluated in
unsigned arithmetic. A packet with msg->len == 0 therefore wraps the
result to a huge value which, assigned to the signed int len, becomes -1.
The following bounds check is signed:
if (len > MAXPARAMLEN + 1)
return false;
so -1 passes, and memcpy(A.data, number->data, len) runs with len cast to
size_t (~SIZE_MAX) against the 257-byte abuf, crashing the daemon.
Neither parse_message() nor handle_packet() validate msg->len (only the
captured packet length), so an unauthenticated attacker on the local
segment can reach this path and crash ead with a single crafted packet.
Validate the claimed length in unsigned arithmetic before the subtraction
and bound it on both sides. Doing the upper-bound check unsigned as well
also closes a 32-bit-only variant where sizeof(ead_packet) + msg->len
overflows in handle_packet(), letting a large msg->len reach the same
negative-len path.
Link: https://github.com/openwrt/openwrt/security/advisories/GHSA-9558-77jp-g3fw
Reported-by: @Vasco0x4
Assisted-by: Claude:claude-opus-4-8
(cherry picked from commit 63c0767f3d)
Link: https://github.com/openwrt/openwrt/pull/24298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenSSL 3.0.21 is a security patch release. The most severe CVE fixed in
this release is High.
This release incorporates the following bug fixes and mitigations:
* Fixed heap use-after-free in PKCS7_verify(). (CVE-2026-45447)
* Fixed CMS AuthEnvelopedData processing may accept forged messages.
(CVE-2026-34182)
* Fixed AES-OCB IV ignored on EVP_Cipher() path. (CVE-2026-45445)
* Fixed possible heap buffer overflow in ASN.1 multibyte string
conversion. (CVE-2026-7383)
* Fixed out-of-bounds read in CMS password-based decryption.
(CVE-2026-9076)
* Fixed heap buffer over-read in ASN.1 content parsing.
(CVE-2026-34180)
* Fixed possible NULL dereference in password-dased CMS decryption.
(CVE-2026-42766)
* Fixed FFC-DH peer validation uses attacker-supplied q.
(CVE-2026-42770)
* Fixed incorrect tag processing for empty messages in AES-GCM-SIV and
AES-SIV modes. (CVE-2026-45446)
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/23843
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix an error while building target/linux x64 on macOS 15.4 host,
due to the PATH_MAX macro being redefined:
mkdir -p /Volumes/test/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.86/tools/objtool && make O=/Volumes/test/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.86 subdir=tools/objtool --no-print-directory -C objtool
exec-cmd.c:15:9: error: 'PATH_MAX' macro redefined [-Werror,-Wmacro-redefined]
15 | #define PATH_MAX 4096
| ^
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/sys/syslimits.h:103:9: note: previous definition is here
103 | #define PATH_MAX 1024 /* max bytes in pathname */
| ^
exec-cmd.c is compiled as part of objtool to run on the host, and
therefore host headers are used, where PATH_MAX is already defined.
Using an old OpenWRT snapshot from 2025-02-16, where linux-6.6.77
used to build correctly, does not help. Reverting from Xcode 16.3 to
16.2 does not help either.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18530
(cherry picked from commit b77e6cd627)
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23710
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Extreme Networks AP3935's LAN1 port (gmac0/RGMII to AR8035 at MDIO
addr 1) fails to acquire a link if no Ethernet cable is connected at
power-on; the port stays dead even after a cable is later inserted, and
only a network restart recovers it.
The AR803x family enables hibernation mode by default, this setting
overrides it.
Signed-off-by: Grische <github@grische.xyz>
Link: https://github.com/openwrt/openwrt/pull/23208
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 33ed49c948)
The mvebu target has CONFIG_CPU_V7 enabled even for aarch64 target,
resulting CONFIG_arm_v7 to be true, which breaks build there.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit d123e5d86a)
Backport upstream patch fixing offload support in the presence of GDM2
interface.
(cherry picked from commit b7aa0aa9bf)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Debian changelog:
* Update Mozilla certificate authority bundle to version 2.82
The following certificate authorities were added (+):
+ TrustAsia TLS ECC Root CA
+ TrustAsia TLS RSA Root CA
+ SwissSign RSA TLS Root CA 2022 - 1
+ OISTE Server Root ECC G1
+ OISTE Server Root RSA G1
The following certificate authorities were removed (-):
- GlobalSign Root CA
- Entrust.net Premium 2048 Secure Server CA
- Baltimore CyberTrust Root (closes: #1121936)
- Comodo AAA Services root
- XRamp Global CA Root
- Go Daddy Class 2 CA
- Starfield Class 2 CA
- CommScope Public Trust ECC Root-01
- CommScope Public Trust ECC Root-02
- CommScope Public Trust RSA Root-01
- CommScope Public Trust RSA Root-02
* Use dh_usrlocal to create /usr/local/share/ca-certificates
(closes: #1127100)
Signed-off-by: Fengyu Wu <saldry@proton.me>
Link: https://github.com/openwrt/openwrt/pull/23155
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 403c52db37)
This version fixes some security problems:
* Client impersonation while resuming a TLS 1.3 session
(CVE-2026-34873)
* Entropy on Linux can fall back to /dev/urandom (CVE-2026-34871)
* PSA random generator cloning (CVE-2026-25835)
* Compiler-induced constant-time violations (CVE-2025-66442)
* Null pointer dereference when setting a distinguished name
(CVE-2026-34874)
* Buffer overflow in FFDH public key export (CVE-2026-34875)
* FFDH: lack of contributory behaviour due to improper input validation
(CVE-2026-34872)
* Signature Algorithm Injection (CVE-2026-25834)
* CCM multipart finish tag-length validation bypass (CVE-2026-34876)
* Risk of insufficient protection of serialized session or context data
leading to potential memory safety issues (CVE-2026-34877)
* Buffer underflow in x509_inet_pton_ipv6() (CVE-2026-25833)
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/mbedtls-3.6.6
Size increases by 470 bytes on aarch64:
343995 bin/packages/aarch64_generic/base/libmbedtls21-3.6.5-r1.apk
344465 bin/packages/aarch64_generic/base/libmbedtls21-3.6.6-r1.apk
Link: https://github.com/openwrt/openwrt/pull/22787
(cherry picked from commit f48ef0040b)
Link: https://github.com/openwrt/openwrt/pull/23362
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It was discovered that the internal PHY interrupt are not always connected
and PHY link up/down is not correctly detected.
This is the case of the Nokia Valyrian board that suffer from this problem.
To handle this, drop the internal PHY interrupt property from DTSI and add
it only to the Gemtek W1700K DTS where it was reported to work correctly.
(cherry picked from commit 89d8dc13d0)
[ drop Gemtek W1700K ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport new field_prep()/get() particularly useful to handle case where a
bitmask is not const and FIELD_PREP can't be used. This permit to replace
manual shift with these macro. (also needed to permit backport of some
patch without modification)
Backport reworked patch that drop the local field_prep()/get() macro in
favor of the global one.
Link: https://github.com/openwrt/openwrt/pull/22479
(cherry picked from commit 25f92aaae1)
[ fix conflict error, drop invalid patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport more upstream patch to include all the fixes pushed upstream and
add all the preliminary patch for multi-serdes support.
While at it also move 2 patch in the 6xx numbering to the 000-1xx backport
numbering to keep things tidy.
All the affected patch manually and automatically refreshed.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ add comment, renumber patch, add more patch, fix PCS patch ]
Link: https://github.com/openwrt/openwrt/pull/22479
(cherry picked from commit c5a8ddd0ac)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Commit 8f1914053b ("airoha: replace I2S patch with upstream pending
version") introduced a kernel panic with I2S driver.
Add the fixed patch to fix the kernel panic.
Fixes: 8f1914053b ("airoha: replace I2S patch with upstream pending version")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit cc57e155a6)
Replace I2S sound patch with upstream pending version. This adds ETDM
support and fix various bug in the downstream implementation.
(cherry picked from commit 8f1914053b)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop airoha,x2-mode related property from the DTSI and enable them only in
the relevant devices that use a PCIe0 line. x2-mode should be enabled only
for the WiFi card that would use it as it might cause problem for WiFi card
that expect 2 single PCIe x1 line instead of a single PCIe x2 line.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0bf1870245)
Fix two hardware initialization issues in the EN7581 PCIe controller
and add support for x2 (2-lane) link mode.
Fixes:
The upstream EN7581 PCIe initialization writes EQ presets and PIPE
configuration registers before clk_bulk_prepare_enable(). Since the
MAC clocks are not yet running at that point, these register writes
are silently dropped, leaving the hardware with default values. This
can cause link training failures or suboptimal equalization.
Additionally, after link training the MAC may only advertise Gen1-Gen2
capability in the Link Capabilities 2 register despite the PHY being
configured for Gen3. A serdes reset toggle forces the MAC to re-read
PHY capability, recovering Gen3 8GT/s link speed.
Both issues are addressed by separating PERST from the clock callbacks
(patch 911), allowing the PCIe controller driver to properly sequence
PERST, clock enable, and register writes (patch 912).
New feature:
PCIe x2 mode support for EN7581 using the NP_SCU system controller
for serdes mux routing, PERST management, and lane configuration.
Both bonded MACs are configured for x2 operation with proper EQ
presets before link training begins.
Signed-off-by: Ryan Chen <rchen14b@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21978
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8b9bd686e7)
[ refresh patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add specific DTSI for NPU firmware based on the supported WiFi chip and
update the supported device by including the relevant new DTSI.
(cherry picked from commit f075c1148d)
[ drop W1700K dts change ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Introduce the capability to read the firmware binary names from device-tree
using the firmware-name property if available.
This is a preliminary patch to enable NPU offloading for MT7996 (Eagle)
chipset since it requires a different binary with respect to the one
used for MT7992 on the EN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/22289
(cherry picked from commit 123557f0e2)
[ refresh patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
OpenSSL 3.0.20 is a security patch release. The most severe CVE fixed in
this release is Moderate.
This release incorporates the following bug fixes and mitigations:
* Fixed incorrect failure handling in RSA KEM RSASVE encapsulation.
(CVE-2026-31790)
* Fixed potential use-after-free in DANE client code.
(CVE-2026-28387)
* Fixed NULL pointer dereference when processing a delta CRL.
(CVE-2026-28388)
* Fixed possible NULL dereference when processing CMS
KeyAgreeRecipientInfo.
(CVE-2026-28389)
* Fixed possible NULL dereference when processing CMS
KeyTransportRecipientInfo.
(CVE-2026-28390)
* Fixed heap buffer overflow in hexadecimal conversion.
(CVE-2026-31789)
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/23346
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Stop overriding CCACHE_COMPILERCHECK from rules.mk and rely on
ccache's default, which hashes the compiler binary's mtime and
size.
For a local tree that is enough: the toolchain only changes when
it is rebuilt, and a rebuild updates mtime and size. Users who
want a stricter check can still set CCACHE_COMPILERCHECK in their
environment.
CI does not depend on this export either. The workflow writes a
secondary ccache.conf with
compiler_check=string:<toolchain-commit-sha>
so the cache key is tied to the toolchain source revision. That
is both stricter than the previous "%compiler% -v -c" setting
and portable across runners, where compiler mtimes would not
match after restoring a cache archive.
Link: https://github.com/openwrt/openwrt/pull/22995
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3956287514)
Update the compiler check for ccache so we don't
end up with the wrong binaries. Right now the
compiler check will not be able to correctly
distinguish the compiler used for build
ARMv8 binaries from the one used to build
ARMv7 binaries.
Signed-off-by: Markus Gothe <markus.gothe@genexis.eu>
Link: https://github.com/openwrt/openwrt/pull/16290
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 3859e8eeb8)
Drop HIDDEN option from U-Boot default for Airoha while support for ATF
gets pushed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit cce81ed05b)
Introduce support for U-Boot for Airoha EN7581/AN7583. For EN7581
initial patch are already in U-Boot mainline and doesn't require
backport, for AN7583 some patch are still pending but already posted
upstream.
Also add for now, precompiled binary for ATF BL2 and BL31. Support for
ATF is planned and will come later.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 04f6769a4a)
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: 128MB SPI-NAND (W25N01GVZEIG)
RAM: 512MB DDR3 (W634GU6QB)
Ethernet: 3x 1GbE (MT7531) + 1x 2.5GbE (EN8811H)
WiFi: MediaTek MT7975(P)N
Button: Mesh, Reset
Power: DC Jack 12V
Flash instructions:
Login into the webUI and flash sysupgrade.bin without saving
configurations.
While at it, create a shared dtsi for X60 and X60-Pro devices and
assign MAC using NVMEM as much as possible. The SPI frequcency has
been increased to 52 MHz as well since the chip supports up to
108 MHz.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
- adopted MTD partition size increase from 64M to 128M
-> this allows boot to complete
- moved MAC addressing stuff out of partition definitions
- all MAC addressing stuff is in .dtsi
Specifications:
SoC: MediaTek MT7981B
RAM: 256MiB
Flash: Winbond SPI-NAND 128 MiB
Switch: 1 WAN, 3 LAN (Gigabit) MediaTek MT7531
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7981B 2.4Ghz & 5.8Ghz
Led Layout from bottom to top:
Power
Mesh (RGB Led, user controllable, default set to OpenWrt Status)
WLAN 2 GHz (user controllable)
WAN (user controllable)
LAN3
LAN2
LAN1
WLAN 5 GHz (Not on front panel but blinks through enclosure,
user controllable)
Buttons:
Reset
Mesh (user controllable, no default function)
Installation:
A. Through U-Boot menu:
- Prepare your connecting computer to use a static IP in
network 192.168.1.0/24
- Power down the router and hold in the Reset button.
- While holding in the button power up the router again.
- Hold the button in for 10 seconds and then release.
- Use your browser to go to 192.168.1.1
- If you see a GUI allowing for flashing firmware then
you got the right model.
- Upload the sysupgrade file.
Note: Recovery GUI can be used to recover from an incorrect
firmware flash.
B. Through OpenWrt Dashboard:
If your router comes with OpenWrt preinstalled
(modified by the seller), you can easily upgrade
by going to the dashboard (192.168.1.1) and then
navigate to System -> Backup/Flash firmware,
then flash the firmware
MAC Addresses were found in Factory partition:
offset 0x4 F8:5E:3C:xx:xx:aa --> Router Label -2
offset 0xa F8:5E:3C:xx:xx:bb --> Router Label -1
offset 0x24 F8:5E:3C:xx:xx:cc --> Router Label +1
offset 0x2a F8:5E:3C:xx:xx:yy --> printed on Router Label
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 479f1403f2)
- Use .dtsi for old z8103ax featuring a 64M Nand
- Prepare .dtsi for model C of z8103ax featuring a 128M Nand
This .dtsi is supposed to match boards labeled as hardware
revision Z8103AX_V01. Model variant D of zbt-z8103ax appears
to use very same board.
DTS include does also
- set wifi mac addresses in &wifi section
- set eth mac addresses in ð section
- set LAN switch mac addresses in &switch section
All of the above allows to get rid of 11_fix_wifi_mac script
Signed-off-by: Jörg Seitz <github.joeterminal@xoxy.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b21b019af4)
The GitHub CI was sometimes still building some tools again even when
the same version was already pre-built. This change fixes the problem
and should improve the speed of the GitHub CI actions. The duration of
the "Build tools" step will be reduced from 5 to 20 minutes down to
10 to 15 seconds.
make also checks that dependencies are not more recent than the target
it wants to build. Previously find returned files in an arbitrary order
and touch set the current timestamp. Since touch is called per file the
timestamps differ in fractional seconds, so not all files got the same
time. make detected a more recent dependency and started to rebuild.
Now all files are set to the same timestamp and make will assume
everything is up to date.
It is sufficient to only touch the stamp files to prevent rebuilding.
Link: https://github.com/openwrt/openwrt/pull/22888
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit cd6cb9f765)
Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an
additional parameter `is_void`. SWIG_AppendOutput remains unchanged.
This was fixed upstream in u-boot/u-boot@a63456b
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function '_wrap_fdt_next_node':
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function 'SWIG_Python_AppendOutput'
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 363e07d.
Signed-off-by: Trix Taiclet <git@trix.moe>
Link: https://github.com/openwrt/openwrt/pull/22870
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an
additional parameter `is_void`. SWIG_AppendOutput remains unchanged.
This was fixed upstream in u-boot/u-boot@a63456b
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function '_wrap_fdt_next_node':
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function 'SWIG_Python_AppendOutput'
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 363e07d.
Signed-off-by: Trix Taiclet <git@trix.moe>
Link: https://github.com/openwrt/openwrt/pull/22870
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No need to add another aliases node just for the label-mac-device,
luckily DTC was smart enough to combine them together in the final DTB.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1f535037b1)
The bootcount init script is missing the executable bit (644 instead of 755),
causing the script to not be executable:
/etc/preinit: line 44: /etc/init.d/bootcount: Permission denied
Fixes: c3b8108a2b ("ramips: Add support for Xiaomi MiWiFi 3A")
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/22446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit a15b224e83)
Update procd cherry-picking fixes from main branch to dedicated
openwrt-24.10 backport branch.
c59f2d8 instance: don't print error in case cgroups are disabled
196291a instance: use positive error numbers for strerror()
d23ddec rcS, ubus: constify char * arguments and variables where appropriate
aeeef20 instance: use mkdir_p helper
d033b7c signal: handle SIGUSR1 as halt
8bc8377 cgroups: fix syntax error
909d02b instance: check length of names when creating cgroups
5ec782f procd: jail/cgroups: fix OOB write in cgroups_apply()
8581313 hotplug-dispatch: fix filter disallowing setting PATH
6265463 service instance: Improve handling of watchdog config changes
45bef92 service instance: Fix overwriting of watchdog linked list members
8294471 coldplug: fix missing header include
fb1c92b hotplug-dispatch: fix missing header include
6dafa86 initd/coldplug: create /dev/null before running udevtrigger
c268f13 hotplug-dispatch: redirect output to /dev/null
b8c4f86 hotplug-dispatch: use stat if d_type is DT_UNKNOWN
1f2aa1a system: fix arguments validation in ubus handler
7e5e049 service: fix use-after-free on service data update
3f48d76 instance: convert jail feature flags to bitmap
2c7c0d2 rcS: avoid duplicate pending "running" calls
5a9b16d service: re-run init script "running" command after instance restart
d5a45ff jail: fix NULL-pointer dereference when connection to ubus failed
8de8cdf jail: always handle mkdir() return value
fa594db jail: seccomp-oci: fix uninitialized pointer read in error path
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
a52cdb354d13 dns: validate IPv4 record addresses
b798c24205b5 dns: validate IPv6 record addresses
a3dcb4adc635 dns: validate reverse dns query name lengths
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
(cherry picked from commit 8a7eb57ab8)
75bedc5 wireless-regdb: Update regulatory info for Australia (AU) for 2025
a6e5195 wireless-regdb: Update broken link in regulatory.bin(5) manpage
9e8c67f wireless-regdb: Update regulatory info for Malaysia (MY) for 2024
61a4637 wireless-regdb: Update regulatory info for Malaysia (MY) for 2025
5cefe55 wireless-regdb: Update regulatory info for Tunisia (TN) on 6GHz for 2025
1a729ae wireless-regdb: Update regulatory info for Canada (CA) for 2025
ea20dfa wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/22150
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7c5e329b54)
5a81c108d20e CMakeLists: update cmake minimum required version to 3.10
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5bfb5ee68f)
The MT7531 has an incorrect interrupt number described in the DTS.
This commit also adds PHY interrupts. They work the same as on
the MT7988.
Tested on Gemtek W1700k.
Suggested-by: Benjamin Larsson <benjamin.larsson@genexis.eu>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21016
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 788958880b)
[ fix conflict error, adapt for kernel 6.6 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cleanup kernel config and drop all unrelated configs. This have the side
effect of fixing the port not going up automatically due to Bridge VLAN
Filtering disabled.
Link: https://github.com/openwrt/openwrt/pull/18112
(cherry picked from commit 7805100e15)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport changes to the pinctrl driver to bring it closer to
the upstream version. Also fix the bug in the pinctrl driver:
pinctrl-airoha ...pinctrl: invalid function mdio in map table
Fixes: bd7f5b3 ("airoha: replace AN7583 pinctrl patch with upstream version")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20770
(cherry picked from commit 69f0ee5baf)
[ fix conflict errors, adapt to 6.6 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace Airoha AN7583 pinctrl patch with upstream version as it has been
accepted upstream. Add the related kernel version tag to identify it.
(cherry picked from commit bd7f5b32a6)
[ fix conflict errors, adapt to 6.6 ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The shared reset procedure of MT7610 and MT7612 stop all queues before
starting the reset sequence.
They however never restart these like other supported mt76 chips
do in the reconfig_complete call. This leads to TX not continuing
after the reset.
Restart queues in the reconfig_complete callback to restore
functionality after the reset.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://patchwork.kernel.org/project/linux-wireless/patch/20251129023904.288484-1-mail@david-bauer.net/
On MT7620-class platforms (CONFIG_NET_RALINK_MT7620) we observe sporadic
wrong-jump-targets, kernel oopses, hanging, corrupted backtraces or even
"half-written" instructions when the compiler emits a direct 'jal imm26'
call.
This is triggered in:
- the small random helpers inside get_random_u32_below(), and
- the blkcg_maybe_throttle_current() call in resume_user_mode_work().
This patch forces those two call sites to use an indirect call via
a volatile function pointer (load into register + jalr) when building
for MT7620, avoiding embedding a 26-bit immediate jump target.
Additionally, on MT7620 builds the exec path in fs/exec.c is modified:
- skip arch_align_stack() + PAGE_ALIGN() in setup_arg_pages()
because the micro-randomization (< PAGE_SIZE) implemented by many
ports (including MT7620) is negated immediately by PAGE_ALIGN().
Skipping the redundant PAGE_ALIGN() reduces exposure to the
problematic code pattern.
These changes are targeted workarounds for MT7620; behavioral logic is unchanged.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/20553
(cherry picked from commit 22ccb445e6)
Link: https://github.com/openwrt/openwrt/pull/22216
Signed-off-by: Robert Marko <robimarko@gmail.com>
The GPIO line connecting to the reset signals of the GS1900-24E(A1)'s
external ICs (RTL8218B phys and RTL8231 expander) cannot be asserted by
the MDIO subsystem, as the reset is shared between busses.
To prevent users from accidentally asserting the reset line, a GPIO hog
is created to permanently de-assert the signal, reliably keeping the
phys and GPIO expanders on.
Tested-by: Simon Fischer <simi.fischa@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit ba57225066)
The reset line wired to the RTL8231 on the GS1900 series may also
connect to other external ICs on the board. On the GS1900-24E, the
reset line is wired (via buffers) to the board's RTL8231 expanders and
the RTL8218 phys. As these external devices (phys) are on different
busses, the reset line shouldn't be specified on one bus or the other.
Drop the reset specification from the generic GPIO description, so it
can be added back on a per-device basis after confirming the behavior.
Link: https://github.com/openwrt/openwrt/issues/18620
Fixes: fd978c2e80 ("realtek: Enable Zyxel GS1900's RTL8231 reset line")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit cdbd9eb448)
Newer Cudy WR3000H units have a Motorcomm YT8821 PHY instead of a
Realtek PHY on the WAN port. Before this commit, the Motorcomm PHY
could not be autodetected by the kernel -- the PHY would show up as
just a generic clause 45 PHY and the proper driver would not be loaded.
The cause of the detection failure likely was that the YT8821 PHY was
held in reset during PHY detection. To fix this, move the reset GPIO
definition to the MDIO bus level. This reset line is deasserted before
the autodetection process, see also [1]. With this change, both Realtek
and Motorcomm PHYs can be supported with a single device tree.
[1]: https://lore.kernel.org/all/20251119134750.394655-1-horatiu.vultur@microchip.com/
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21399
(cherry picked from commit 02f0efd60b)
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21531
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A recently introduced hardware revision of the Cudy WR3000H
router uses the Motorcomm YT8821 PHY chip on its 2.5G WAN port.
Backport the YT8821 enablement patch to the 6.6 kernel to make
the new WR3000H supportable on OpenWrt 24.10.
Signed-off-by: Jakub Vaněk <linuxtardis@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21531
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
OpenSSL 3.0.19 is a security patch release. The most severe CVE fixed
in this release is High.
This release incorporates the following bug fixes and mitigations:
* Fixed Stack buffer overflow in CMS AuthEnvelopedData parsing.
(CVE-2025-15467)
* Fixed Heap out-of-bounds write in BIO_f_linebuffer on short writes.
(CVE-2025-68160)
* Fixed Unauthenticated/unencrypted trailing bytes with low-level OCB
function calls. (CVE-2025-69418)
* Fixed Out of bounds write in PKCS12_get_friendlyname() UTF-8
conversion. (CVE-2025-69419)
* Fixed Missing ASN1_TYPE validation in TS_RESP_verify_response()
function. (CVE-2025-69420)
* Fixed NULL Pointer Dereference in PKCS12_item_decrypt_d2i_ex()
function. (CVE-2025-69421)
* Fixed Missing ASN1_TYPE validation in PKCS#12 parsing.
(CVE-2026-22795)
* Fixed ASN1_TYPE Type Confusion in the PKCS7_digest_from_attributes()
function. (CVE-2026-22796)
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/21831
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Based on commit 9a368bb4e4 ("kernel: add support for FudanMicro FM25G02B").
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 7851d11e3f)
Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an
additional parameter `is_void`. SWIG_AppendOutput remains unchanged.
This was fixed upstream in u-boot/u-boot@a63456b
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 363e07d and 71b5de6.
This commit is not part of the main branch, as the main branch has
already bumped past 2025.01, removing the need for this patch.
uboot-rockchip had the patch removed as part of 92814fe, which was the
bump to 2025.01.
Signed-off-by: Trix Taiclet <git@trix.moe>
Link: https://github.com/openwrt/openwrt/pull/21415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Swig 4.3.0 has changed SWIG_Python_AppendOutput, which now requires an
additional parameter `is_void`. SWIG_AppendOutput remains unchanged.
This was fixed upstream in u-boot/u-boot@a63456b
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 363e07d.
Fixes: #20619
Link: #20620
Signed-off-by: Trix Taiclet <trix@c3l.lu>
Link: https://github.com/openwrt/openwrt/pull/20620
(cherry picked from commit 71b5de61ae)
Signed-off-by: Trix Taiclet <git@trix.moe>
Link: https://github.com/openwrt/openwrt/pull/21415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
This is the same fix as applied in 4e68103c4e ("uboot-rockchip: fix build with swig 4.3.0")
Link: https://github.com/openwrt/openwrt/pull/20538
(cherry picked from commit 363e07dfa2)
Signed-off-by: Trix Taiclet <git@trix.moe>
Link: https://github.com/openwrt/openwrt/pull/21415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These SOC_CON1 regs needs to be cleared before a reset or the
BOOT_MODE_REG do not retain its value and it is not possible
to reset to bootrom download mode once TF-A has been started.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 8b63a55fe2)
The SUPPORTED_DEVICES sets for both Maxlinear (v1) and Airoha (v2)
devices were identical, so sysupgrade was unable to detect when an
incorrect image was being installed. This caused "soft bricking" of
devices when a v1 image was installed on a v2 device, and vice versa.
Fix this by making the supported_devices distinct for each device
version, by renaming the devices with a version-specific name.
This is reflected in the file name and the image metadata.
Fixes: https://github.com/openwrt/openwrt/issues/20566
Fixes: https://github.com/openwrt/asu/issues/1525
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20632
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b71f4665cd)
The probe order for PCIe buses and devices is non-deterministic,
making the names eth0 and eth1 unpredictable (they may be swapped).
This patch fixes the names by referencing the device path using
`ucidef_set_network_device_path`.
The mapping between silkscreen labels on the board/case and OpenWrt
interface names is as follows:
- E52C
LAN: lan
WAN: wan
- ROCK 5 ITX
RJ45 1: eth0
RJ45 2: eth1
- ROCK 5T
RJ45_1: eth0
RJ45_2: eth1
For Radxa E52C, this breaks compatibility of the network config;
therefore, set DEVICE_COMPAT_VERSION to `1.1`.
Fixes: d16d2765bd ("rockchip: add support for Radxa E52C")
Fixes: 0839345211 ("rockchip: add support for Radxa ROCK 5 ITX/ITX+")
Fixes: 4a78af9876 ("rockchip: add support for Radxa ROCK 5T")
Link: https://github.com/openwrt/openwrt/issues/20202
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/20608
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1f1db75432)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Radxa E52C is a compact network computer using the Rockchip RK3582
SoC.
- https://radxa.com/products/network-computer/e52c
Hardware
--------
- Dual Cortex-A76 and Quad Cortex-A55 CPU
- 5 TOPS NPU
- 2/4/8GB LPDDR4 RAM
- 16/32/64GB on-board eMMC
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB Type-C debug port
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d16d2765bd)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Radxa ROCK 5C (Lite) is a single board computer using the Rockchip
RK3588S2 (RK3582) SoC.
- https://radxa.com/products/rock5/5c
Hardware
--------
- Quad (Dual) Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU (5C only)
- 6 (5) TOPS NPU
- 1/2/4/8/16/32GB LPDDR4X RAM
- eMMC/SPI NOR flash connector
- microSD card slot
- Wi-Fi 6 (AIC8800D80, not yet supported)
- Gigabit Ethernet port with PoE (additional PoE HAT required)
- USB 3.1 Gen1 Type-A HOST/OTG port
- USB 3.1 Gen1 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- FPC connector with PCIe 2.1 x1
- PWM fan connector
- 20x2 pin header
- USB Type-C power port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 071aa994cd)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The Radxa ROCK 5 ITX(+) is a Mini-ITX form factor computer using the
Rockchip RK3588 SoC.
- https://radxa.com/products/rock5/5itx
- https://radxa.com/products/rock5/5itxp
Hardware
--------
- Quad Cortex-A76 and Quad Cortex-A55 CPU
- Mali-G610 MP4 GPU
- 6 TOPS NPU
- 4/8/16/24/32GB LPDDR5 RAM
- on-board eMMC
- 16MB SPI NOR flash
- microSD card slot
- 2x 2.5 Gigabit Ethernet ports with PoE (additional PoE module required)
- USB 3.1 Gen1 Type-C HOST/OTG port
- 4x USB 3.1 Gen1 Type-A HOST ports
- 2x USB 2.0 Type-A HOST ports
- M.2 M Key connector with PCIe 3.0 x2
- 4x SATA connectors (ITX only)
- 2nd M.2 M Key connector with PCIe 3.0 x2 (ITX+ only)
- M.2 E Key connector with PCIe 2.1 x1 and USB 2.0
- RTC battery socket for CR1220
- 4pin PWM fan connector
- Serial console pin header
- Front panel pin headers
- 24pin ATX power connector
- 5525 12V DC jack
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/19867
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0839345211)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The EW71v2 has the WAN port configured at eth1.
The printed label-mac is configured on this iface in openwrt.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit 7f3537ee2c)
TSO and/or RX checksum offload may need to be disabled on the conduit
interface (gmac1).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 68b4cf8dd0)
backport upstream commit 095151b235 (mediatek: fix pwn fan settings for
sinovoip bpi-r3 (v3))
Popular cheap PWM fans for this machine, like the ones coming in
heatsink+fan combos will not work properly at the currently defined
medium speed. Trying different pwm setting using a command
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
Current cooling levels are:
cooling-levels = <255 96 0>;
Thus only cpu-active-high and cpu-active-low modes are usable.
This patch fixes cpu-active-medium settings for bpi-r3 board.
This patch may not be enough. Users may wants to tweak their thermal_zone0
trip points, thus tuning fan rotation speed depending on cpu temperature.
That can be done on the base of the following example:
=== example =========
# cpu temperature below 25 Celsius degrees, no rotation
echo 25000 > /sys/class/thermal/thermal_zone0/trip_point_4_temp
# cpu temperature in [25..32] Celsius degrees, normal rotation speed
echo 32000 > /sys/class/thermal/thermal_zone0/trip_point_3_temp
# cpu temperature above 50 Celsius degrees, max rotation speed
echo 50000 > /sys/class/thermal/thermal_zone0/trip_point_2_temp
=====================
Changes v2:
* put patch to a proper directory
* updated patch description
* tested with latest openwrt based on linux-6.6
Changes v3:
* use upstream linux patch
* update patch description
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21252
Signed-off-by: Robert Marko <robimarko@gmail.com>
e51d568 wireless-regdb: update regulatory rules for Botswana (BW) for 2022
5afc632 wireless-regdb: update regulatory rules for Sint Marteen (SX) for 2018
b484a31 wireless-regdb: Update regulatory info including bandwidth for Costa Rica (CR) for 2023
39e5e04 wireless-regdb: Permit lower 6 GHz band for Kazakhstan (KZ)
a827d3a wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/20544
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b4a8ba2e88)
Currently its only possible to disable port forwarding only for specific
keys, via the OpenSSH-style restriction in `authorized_keys` file.
In some use cases it might be feasible to disable such features globally
on service level, so lets add new LocalPortForward and RemotePortForward
config knobs.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/21071
(cherry picked from commit 83f6177dbf)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix Totolink X6000R image failing to upgrade via sysupgrade due to an
incorrect upgrade case. The fallback upgrade path used the NAND upgrade
routine, which caused the "layout volume not found" error on NOR flash
devices. By adding a specific case for this board, sysupgrade now uses
`default_do_upgrade`, which is compatible with the NOR flash layout.
Fixes: 7cd10ad
Signed-off-by: Ayra Hikari <ayrahikari@linuxmail.org>
(cherry picked from commit 7cd10add2d)
Link: https://github.com/openwrt/openwrt/pull/20674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification :
- SOC : Mediatek MT7981B (1.3GHz)
- RAM : 256MB
- Flash : 16MB SPI NOR
- Ports : 4 LAN (1G) & 1 WAN (1G)
- WIFI : MediaTek dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Buttons : Reset & WPS/Mesh
- LEDS : WAN (Green), Status (Red & Blue)
- Power : 12V1A
Install via OEM web ui:
Upload the sysupgrade image to firmware upgrade page on OEM web ui
Install via recovery / revert to stock firmware:
1. Unplug from power
2. Download the Sysupgrade (for openwrt installation) or OEM Factory image (for revert to stock firmware)
3. Set your computer ethernet IP to 192.168.1.X, subnet 255.255.255.0 (X=your chosen ip number ranging from 2-254)
4. Press and hold reset button while turn on / plug power adapter to the router. Wait untill ALL LAN green LED turn on, then release the reset button.
5. Plug the LAN cable from your computer into LAN 1 port then open web browser, and type in the address column : 192.168.1.1
6. Upload the sysupgrade / oem factory image
7. Wait until the router finished flashing (the router will reboot)
8. Set ethernet ip to dhcp
9. Open 192.168.1.1 (for openwrt install) / 192.168.0.1 (for OEM firmware)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20035
(cherry picked from commit 7cd10add2d)
Signed-off-by: Ari Kurniawan <noobhek@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20674
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since kernel 6.1, the Watchguard Firebox T10 can't boot anymore due to
increased kernel size.
This commit introduces the zImage loader from 7d768a9 to boot the kernel.
This is required, since the U-Boot version used in this device appears
to have a hard limit of 16MB for the kernel size it can handle. The
current kernel size is around 17MB, though, due to kernel page alignment
required for memory protection.
(cherry-picked from commit be7aa5bda4)
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21130
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR fixes support for Cudy r700.
Original PR: https://github.com/openwrt/openwrt/pull/18532
Fixed:
- WAN port functionality;
- RESET button;
- Status LED;
- LAN port names consistent with the chassis;
- Merged partitions "debug", "backup" & "firmware" to one partition "firmware" ("debug" & "backup" contained unimportant data);
- Removed redundant DTS elements.
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Fixes: 75403dd1d0 ("ramips: add support for Cudy R700")
Link: https://github.com/openwrt/openwrt/pull/20756
(cherry picked from commit 35a86267e9)
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is the same hardware as the Cudy WR2100 that's
had support for some time now, just without the WLAN
hardware.
This PR is mostly copied from the commit that added
support for the WR2100, here: 3501db9
Specifications:
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 5x Gbit ports
Installation:
There are two known options:
The Luci-based UI.
Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
A signed firmware can be found in GitHub PR #18532.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Link: https://github.com/openwrt/openwrt/pull/18532
Signed-off-by: David DeGraw <degraw@fastmail.com>
(cherry picked from commit 75403dd1d0)
Link: https://github.com/openwrt/openwrt/pull/21068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for Cudy C200P.
Because v24.10 stable has no regulator definition, so we cannot make simple cherry-pick. We need another DTS file.
Specifications:
SoC: MediaTek MT7621AT
RAM: 256 MB (DDR3)
Flash: 16 MB (NOR)
POE Chip: IP804AR
Interfaces:
Switch: 1 WAN, 4 LAN (Gigabit)
Gigabit RJ45 PoE Ports on 2~5
Max Power on a Single PoE Ports 30W
PoE Ports : The PoE ports comply with IEEE 802.3at/af standards.
Ports: 1 USB-A 3.0 Ports
LED:
System
PoE Max Status
Link/ACT/PoE Status of Each PoE Port
Physical Buttons:
Reset Button
Power Input:
DC Jack
Power Methods:
DC: 54V 1.11A
802.3at/af PoE
Passive PoE: 24/48V
Max Power Consumption (W):
Total: 60W
PoE: 55W
PoE (when USB Device is plugged in): 50W
No PoE: 5W
Installation:
To install OpenWRT, you need the intermediate firmware from Cudy. (U-boot is locked). After installing the intermediate firmware, you can install OpenWRT via sysupgrade.
Recovery:
TFTP available.
1. Place the recovery.bin in the serving directory of your TFTP server.
2. Set your IP to 192.168.1.88/24.
3. Press the “Reset” button of Cudy router and hold it. Before the Cudy router is powered on and before TFTP start to download the firmware, don't release the “Reset” button.
4. Power on the Cudy router.
5. You can release the reset button only when TFTP starts downloading firmware.
6. When the SYSTEM LED turns solid green, the upgrade is complete.
Serial:
1. Serial connection parameters: 115200 / 8N1
2. Serial connection voltage: 3.3V
PoE is not supported at the time of PR. The IP804R chip is not yet supported by OpenWRT.
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/21064
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628DAN
- Flash: 16 MB
- RAM: 64 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN/LAN, 3x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (PWR): Always Off
Modem (NET): GPIO/3 active-low
LAN: Always On
RF (Modem Signal): GPIO/2 active-low
WIFI: GPIO/44 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using TTL:
1. Connect the board to the computer via TTL.
2. Enter original firmware failsafe mode.
3. Use wget download firmware to board /tmp
4. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h8850-v20-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8850-v20-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20259
(cherry picked from commit 23a070dfb1)
Link: https://github.com/openwrt/openwrt/pull/21007
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
GL-MV1000 external SD controller was broken by a recent kernel update
between OpenWRT releases 24.10.2 and 24.10.3 due to a mistake in Device
Tree: "regulator-gpio" was defined without required "gpios" property.
Since "no-1-8-v" property is also defined for this controller
a switchable vqmmc-supply regulator performs no function - a fixed 3.3V
IO voltage will always be used.
This regulator definition was probably added by mistake from a Device
Tree from another device.
Remove incomplete vcc_sd_reg1 regulator definition to fix this issue.
Issue discussion for reference: openwrt/openwrt#20309
Upstream commit: 6f2325b23d
Signed-off-by: Mikhail Zadorozhnyi <zador.blood.stained+git@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/20378
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ASUS TUF-AX4200Q(TUF 小旋风Pro WiFi6 AX4200) is a home router that adds an additional 2.5G Ethernet port to ASUS TUF-AX4200.
Hardware
- - - - - - - -
- SOC : MediaTek MT7986
- RAM : 512MB DDR3
- FLASH : 256MB SPI-NAND (Winbond W25N02KV)
- WIFI : Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz
- ETH : MediaTek MT7531 Switch
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
- UART : 3V3 115200 8N1 (Pinout silkscreened / Do not ocnnect VCC)
Installation
- - - - - - - -
Vendor-UI Method:
1. Download or make the OpenWrt initramfs.trx image
2. Connect the PC via LAN to one of the yellow router ports and wait until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1/
4. If your router is brand new, finish the setup process and log into the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
TFTP Method:
1. Download the OpenWrt initramfs image.
Copy the image to a TFTP server reachable at 192.168.1.70/24.
Rename the image to tufax4200q.bin.
2. Connect the PC with TFTP server to the TUF-AX4200Q.
Set a static ip on the ethernet interface of your PC.
(IP address: 192.168.1.70, subnet mask: 255.255.255.0)
Connect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 tufax4200q.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot.
Transfer the sysupgrade image to the device using SCP and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
(based on support for ASUS RT-AX52 by achterin and trx image generation by remittor)
Link: https://github.com/openwrt/openwrt/pull/20900
(cherry picked from commit e7086d7a2f)
Signed-off-by: Brian Lee <larte332@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21036
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream commit that fixes handling of multicast packets.
Without this patch, ARP resolution fails, and connectivity from a
station to an AP does not work reliably until traffic is initiated
by the AP.
Signed-off-by: Oliver Sedlbauer <os@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/21088
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for D-Link DIR-2660 A2.
Based on the commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=b5dd746cbb1aaf91f4b68e9f3eda97413550d904,
Both devices look identical, except for the A1/A2 designation.
You can safely install the A1 firmware for the A2 – I've been testing it for several months as a DUMB AP – without any problems.
Specifications:
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (white/orange), Internet (white/orange), WiFi 2.4G (white),
WiFi 5G (white), USB 3.0 (white), USB 2.0 (white)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Marcin Leksmark <lexmark3200@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20020
(cherry picked from commit 485f9b0d31)
Link: https://github.com/openwrt/openwrt/pull/21113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Downloading packages from git requires zstd to compress their tarballs.
Make sure that zstd from host tools is compiled when running make
download. Otherwise, either the download would fail because zstd is not
present or a random version from the host would be used leading to hash
mismatches.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/21125
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f3e4620f59)
This partially reverts 78d259e7d2.
That commit broke mounting the root fs on Sophos RED 15w due to
partition size mismatch, and changed the partition sequence, causing
the OpenWrt partition numbers to change from mtd3:kernel/mtd4:ubi to
mtd4:kernel/mtd5:ubi.
Fixes: 78d259e7d2 ("mpc85xx: fix some dtc warnings")
(cherry-picked from commit 09e7b24ceb)
Signed-off-by: Shine <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/21062
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is currently a logic error with generating the base feed string.
In the scenario where the commit of a Tag match the latest commit of a
stable branch, the stable branch have priority over the tag name.
This results in generating SDK that actually target the branch instead
of the specific tag.
To fix this invert the logic and give priority to the tag name.
Fixes: #18583
(cherry picked from commit 289172b00e)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Branch named main was never filter out on parsing the GIT_BRANCH define.
Add main to the name of branch that should be filtered.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0338dd44d5)
Product name: Wavlink WL-WN536AX6 Rev a "Mighty LX2"
Product link: https://www.wavlink.com/en_us/product/WL-WN536AX6.html
Specifications:
SOC: MT7986AV
RAM: 512MB DDR4
Flash: 128MB SPI NAND
Ports: 4 LAN (1G) & 1 WAN (2.5G)
WIFI: MT7976PN + MT7975N
LEDs: 8 (STATUS, WIFI, WAN, LAN1, LAN2, LAN3, LAN4, PWR)
USB: 1 (3.0)
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3
5G: 80:3F:5D:xx:xx:x4
* Installation with OEM WebUI:
Note: Make sure PC is connected on LAN1 port. The OEM firmware has an unknown root password and settings are kept after upgrading firmware. Therefore, a customized Openwrt firmware is needed to remove the root password on login, by adding `passwd -d root` to /etc/init.d/bootcount. The WebUI does a filename check so the customized firmware is named accordingly.
1. Download modified firmware file `WAVLINK_WN536AX6-A_M36AX6_V250320-WO-437baca-modified.bin` from https://github.com/ses1er/firmware-misc/tree/main/wavlink/wl-wn536ax6a
2. Log into WebUI on default IP: http://192.168.20.1
3. Browse to More (top menu) -> System -> Firmware Upgrade.
4. Under `Local Upgrade` section, check the device to be upgraded and upload downloaded modified firmware. Click `UPLOAD FILE`, then `APPLY`
5. Wait about 2 minutes (ignore progress bar), and browse to http://192.168.20.1. You should see LUCI login page. Username is root and no password.
6. Browse to `System -> Backup/Flash Firmware`, click on `Flash Image`, click `Browse` and locate `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` file.
7. Uncheck `Keep settings and retain the current configuration` and click `Continue`.
8. Router will now be set to IP 192.168.1.1 which is the Openwrt default.
* Installation with UART:
Note: Having UART connected while cold booting the device will result in a kernel panic when initializing wifi. I've found this workaround:
1. Power off the device and ensure UART is not connected to PC.
2. Power up the device, when lights come on, plug in UART.
3. Warm boots and soft restarts will not cause kernel panic for the duration of device being powered on. Repeat steps for subsequent cold boots.
1. Configure TFTP server with IP 192.168.1.66. Copy `openwrt-mediatek-filogic-wavlink_wl-wn536ax6a-initramfs.itb` to TFTP root.
2. Interrupt boot by pressing 0.
3. Run the following in Uboot console: `setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x46000000 openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-initramfs.itb; bootm`
4. Transfer `openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin` to device:
(`scp -O openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/`)
5. Run the following on device: `sysupgrade -n /tmp/openwrt-mediatek-filogic-wavlink_wl-wn536ax6-a-squashfs-sysupgrade.bin`
Signed-off-by: Qing W. <ses1er@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://github.com/openwrt/openwrt/pull/20760
(cherry picked from commit 1748ce8295)
Link: https://github.com/openwrt/openwrt/pull/20775
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware:
- SoC: MediaTek MT7621DAT
- Flash: 16 MiB XM25QH128C
- RAM: 128 MiB
- WLAN: 2.4 GHz (MT7603E, 11n), 5 GHz (MediaTek MT7613BEN, 11ac)
- Ethernet: 1x10/100/1000 Mbps LAN
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 5x Green
- Serial Console: unpopulated header 115200 8n1 (silkscreen on PCB)
- Power: POE 802.3af (37-57V DC)
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x1 | +1 |
+---------+-------------------+-----------+
Installation:
The factory firmware is locked: you can only work with Cudy signed firmware.
Download a intermediate firmware signed by Cudy here:
https://www.cudy.com/blogs/faq/openwrt-software-download
After that, login to the router (192.168.10.254, password "admin") and install the intermediate firmware.
If you can reach LuCI or SSH now on the intermediate firmware, just use the sysupgrade image with the 'Keep settings' option turned off.
Special thanks to Daniel de Kock for starting the porting work at #16265.
Signed-off-by: Luis Mita <luis@luismita.com>
Co-Authored-By: Daniel de Kock <daniel@riot.network>
Co-Authored-By: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/20268
(cherry picked from commit 8fb644e9e8)
Link: https://github.com/openwrt/openwrt/pull/20710
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7986AV quad-core ARM Cortex-A53 2GHz
- RAM : DDR4 512Mbytes, Nanya Technology NT5AD256M16E4
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976DAN, MediaTek MT7916AN, MediaTek MT7976AN
- 2.4GHz : b/g/n/ax, Multi User MIMO
- 5GHz : a/n/ac/ax, Multi User MIMO
- 6GHz : ax, Multi User MIMO
- Ethernet : 10/100/1000 Mbps x4, LAN (MediaTek MT7531AE)
10/100/1000/2500 Mbps x1, WAN (MaxLinear GPY211C0VC)
- UART : 1x4 pin header on PCB
- [J1] 3.3V, TX, RX, GND (115200, 8N1)
- Buttons : WPS, Reset
- Switches : Rfkill Slide Switch
- USB : 1x USB 3.0 (MediaTek MT7986AV peripheral)
- FAN : 1x Fan (off - slow - fast)
- LEDs : 1x Power (Blue)
1x CPU (Blue)
1x Wi-Fi 6GHz (Blue)
1x Wi-Fi 5GHz (Blue)
1x Wi-Fi 2.4GHz (Blue)
4x LAN activity (Blue)
1x WAN activity (Blue)
1x USB 3.0 (Blue)
- Power : 12VDC, 3.5A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+------------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+------------------------+
| WLAN 2.4G | 58:86:94:xx:xx:xx | label1 |
| WLAN 5G | 5A:86:94:xx:xx:xx | label2 with LA Bit set |
| WLAN 6G | 5A:86:94:xx:xx:xx | label1 with LA Bit set |
| WAN | 58:86:94:xx:xx:xx | label1 + 1 |
| LAN | 58:86:94:xx:xx:xx | label1 + 3 |
+-----------+-------------------+------------------------+
The WLAN 2.4G MAC address (label1) was found in 'Factory' partition, 0xA0004
The WLAN 5G MAC address (label2) was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software (ipTIME Firmware Wizard (11ac))
from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router (keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router (LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Note: The router will automatically reboot if no file is uploaded within
55 seconds.
Fan Control
------------
The fan speed is controlled by writing a value from 0 to 2 to the
`fan1_target` file.
```
cd /sys/devices/platform/gpio-fan/hwmon/hwmon2
echo '0' > fan1_target // off
echo '1' > fan1_target // slow
echo '2' > fan1_target // fast
```
Limitation: Enabling Wi-Fi 6E
----------
Wi-Fi 6E (6GHz) does not work out of the box on LuCI.
After installation, you need to configure a few settings in the `radio1`
and `default_radio1` sections of the `/etc/config/wireless`.
Once you have made these changes, you can enable and use Wi-Fi 6E.
In the `radio1` section, you need to add three common options:
- band: must be set to `6g`
- country: a valid country code for the 6GHz band
- channel: a preferrend scanning channel (PSC) for 6GHz
In the `default_radio1` section, you need to add the SSID and key:
- ssid: The public name of your Wi-Fi network
- key: The Wi-Fi password
- encryption: must be set to either `sae` for WPA3 or `owe` for OWE
(open network)
Example:
```
config wifi-device 'radio1'
...
option band '6g'
option country 'KR'
option channel '37'
...
config wifi-iface 'default_radio1'
...
option ssid 'my_wifi_6e_name'
option key 'my_strong_password1234'
option encryption 'sae'
...
```
Note: A list of all the 6GHz PSC channels:
```
5, 21, 37, 53, 69, 85, 101, 117, 133, 149, 165, 181, 197, 213, and 229
```
Limitation: Maximum Transmit Power (Wi-Fi 6E)
----------
The maximum transmit power is currently broken. In the drop-down menu,
you can only choose between "driver default" and "255 dBm (2147493647
mW)". There is currently no workaround for the issue. Please leave the
maximum transmit power set to "driver default".
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19763
(cherry picked from commit 2503e5bc37)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20773
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
MediaTek MT7981 WiSoC
512MB DDR4 RAM
128MB SPI-NAND
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY
UART: 115200 8N1 3.3V
USB2 Port
PoE on WAN Port
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Gotchas:
WAN LED does not light up (might require further DTS tweaks)
PoE on WAN port was not tested
This commit is heavily based on WR3000H one, I've just ported DTS differences
from the official image to get USB support and proper LED mapping.
Installation
------------
[Untested as I've received and used a transitional image from Cudy]
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000p.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: Michal Halva <hedik01@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19636
(cherry picked from commit 04e9d154f2)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Link: https://github.com/openwrt/openwrt/pull/20830
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The generic-rk3568 does not reset the gmac phy, causing the kernel to
fail to initialize gmac during cold boot with the error message
"mdio_bus stmmac-1: MDIO device at address 1 is missing."
Adding a dedicated uboot for EasePi R1 to resolve this issue.
The EasePi R1's DTS hasn't been merged into the Linux release yet,
so it cannot be submitted to the upstream u-boot.
Fixes: ef093299db ("uboot-rockchip: add support for LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20772
(cherry picked from commit 5dff7b45d3)
With changes:
1. Reorder patch file names (`105-*` to `106-*`).
2. configs/easepi-r1-rk3568_defconfig needs CONFIG_SPL_PAD_TO on u-boot 2024.10.
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The probe order for PCIe buses and devices is non-deterministic,
making the names eth2 and eth3 unpredictable (they may be swapped).
This patch fixes the names by referencing the device path using
`ucidef_set_network_device_path`.
This patch ensures that the OpenWrt interface name matches the case label.
Fixes: 8ca4caacd0 ("rockchip: Add support for RK3568 LinkEase EasePi R1")
Signed-off-by: Liangbin Lian <jjm2473@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20779
(cherry picked from commit d7530c1e54)
Link: https://github.com/openwrt/openwrt/pull/20744
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream patch to add support for the ESMT F50L1G41LC flash
chip. It is used in multiple Cudy products manufactured starting
November 2025.
(cherry picked from commit 9424b2b786)
Link: https://github.com/openwrt/openwrt/pull/20963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In implementing APK support it seems a a leftover was never removed that
creates an unused tmp directory in the package feed directory.
Drop it as it's not used anywhere. What is actually needed is the
creation of the $$(PDIR_$(1)) directory for the feed package directory
in the bin/packages directory.
This was a side effect of using INSTALL_DIR on $$(PDIR_$(1))/tmp that
indirectly creates the $$(PDIR_$(1)) parent directory.
Fixes: d788ab376f ("build: add APK package build capabilities")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f9802d70c6)
Airoha AN7581 SoC supports a Network Processor (NPU) to offload WiFi
traffic. Add the required bits to enable the support of it in the MT76
driver. This will be enabled by default if we are compiling for the
Airoha AN7581 SoC.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
[ improve commit title/description ]
Link: https://github.com/openwrt/openwrt/pull/20826
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 79d418eed8)
0aece3089a3a wifi: mt76: mt7996: Remove useless check in mt7996_msdu_page_get_from_cache()
05b3d899ad24 wifi: mt76: Move Q_READ/Q_WRITE definitions in dma.h
85e6517b0ac5 wifi: mt76: Add mt76_dev pointer in mt76_queue struct.
a3b6c67c97d2 wifi: mt76: Add the capability to set TX token start ID
141a81557070 wifi: mt76: Introduce the NPU generic layer
647d11bb17e0 wifi: mt76: mt7996: Add NPU offload support to MT7996 driver
8ff3b2bfc37f wifi: mt76: mt7996: fix typos in comments
0043147439b4 wifi: mt76: mt7925: refactor regulatory domain handling to regd.[ch]
f0e8fe441489 wifi: mt76: mt7925: refactor CLC support check flow
588cc87bf6a2 wifi: mt76: mt7925: refactor regulatory notifier flow
dac1d45fe94b wifi: mt76: mt7925: improve EHT capability control in regulatory flow
c166c4a0e750 wifi: mt76: mt7925: add auto regdomain switch support
d7b059bba166 wifi: mt76: mt7925: disable auto regd changes after user set
84f62a6beb99 wifi: mt76: mmio_*_copy fix byte order and alignment
f5ae5b2e8116 Revert "wifi: mt76: mt792x: improve monitor interface handling"
8ae7e6dc1d3a wifi: mt76: adjust BSS conf pointer handling
1b438ebe0d06 wifi: mt76: mt7925: cqm rssi low/high event notify
7519fa4ce62c wifi: mt76: mt7996: fix max nss value when getting rx chainmask
ea0580ad065f wifi: mt76: mt7996: no need to wait ACK event for SDO command
74112c2956fb wifi: mt76: mt7996: fix implicit beamforming support for mt7992
361d6bdac45d wifi: mt76: mt7996: support fixed rate for link station
d99274cdc30c wifi: mt76: mt7996: fix several fields in mt7996_mcu_bss_basic_tlv()
ad90a85b652b wifi: mt76: mt7996: fix teardown command for an MLD peer
e9fe8bc03e41 wifi: mt76: mt7996: set link_valid field when initializing wcid
050394665502 wifi: mt76: mt7996: use correct link_id when filling TXD and TXP
5d223855552c wifi: mt76: mt7996: fix MLD group index assignment
ab8361dbc421 wifi: mt76: mt7996: fix MLO set key and group key issues
7ce7ab881b3f wifi: mt76: mt7996: fix using wrong phy to start in mt7996_mac_restart()
1e0c23ff754b wifi: mt76: mt7996: fix EMI rings for RRO
eb567bc7f9b6 wifi: mt76: mt7925: ensure the 6GHz A-MPDU density cap from the hardware.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e1a584b5d2)
Since we are not using patch -b, *.orig files are only created when
there are conflicts, or never according to posix patch.
As such, it doesn't really make sense to always delete *.orig files
presuming they are patch backups, even if they are patch backups.
Doing so is both deleting potentially useful information for failed
patch applications and creating hard to diagnose bugs [1].
In a similar vein, checking for *.rej files does not add any value
since we're already checking the patch command's return code.
[1]: https://github.com/openwrt/packages/issues/27485
Signed-off-by: George Tsiamasiotis <george@tsiamasiotis.gr>
Link: https://github.com/openwrt/openwrt/pull/20141
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 75ca6bafd6)
Link: https://github.com/openwrt/openwrt/pull/20742
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
When building in environments that set IS_TTY, the feeds script does not
honor it and passes a hardcoded value to scan.mk, causing unwanted
control characters to appear in stdout.
This commit addresses the issue by checking IS_TTY and MAKE_TERMOUT
variables and uses their values if defined.
Closes#8039
Signed-off-by: Ernestas Kulik <ernestas.k@iconn-networks.com>
Link: https://github.com/openwrt/openwrt/pull/20743
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fd7e43d429)
Backport upstream patch fixing out of order DMA access for ethernet
driver. This is relevant in the context of QoS when packets doesn't
follow linear handling by QDMA HW.
(cherry picked from commit 3169ffa4c7)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
KConfig flag have an extra whitespace for CONFIG_PHY_AIROHA_USB and
value is not ignored.
Drop the extra whitespace to correctly ignore the value on kernel
compilation.
Fixes: c5b12fc02a ("airoha: Introduce support for Airoha AN7583 SoC")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eedc7b3b79)
Replace Airoha AN7581 PWM patch with upstream version and add kernel
version tag.
(cherry picked from commit 2352de96c1)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport upstream minor fixed for NPU handling that might result in
kernel panic or handle leak.
(cherry picked from commit 83eacb6ab0)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Similar to e92b153e99 ("mediatek: introduce KERNEL_LOADADDR to Device/Default template"),
let's move the default loadaddr to Device/Default.
What's more, use 0x80200000 instead of the SDK default value 0x80088000
to avoid the following error which may overwrite TZ memory and cause crash:
[ 0.000000] [Firmware Bug]: Kernel image misaligned at boot, please fix your bootloader!
[ 0.000000] OF: reserved mem: Reserved memory: failed to reserve memory for node 'atf@80000000': base 0x0000000080000000, size 2 MiB
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
[ fix spelling mistake ]
Link: https://github.com/openwrt/openwrt/pull/20470
(cherry picked from commit fed2d31343)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable USB node on eMMC RFB board and disable USB2 3.0 port to make the
3rd PCIe line correctly work.
This is needed to prevent the xHCI driver to mess with PCIe by
configuring the USB2 3.0 port. Port will still be detected but won't be
configureed by the driver and won't have PHY to configure for.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6d51c80424)
The 3rd PCIe line use the USB2 serdes for PCIe operation. Correctly set
it to the DT node so that the mode can be correctly set in the PHY
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ba92e0e32)
Add pending patch for USB support on AN7581 SoC. This is also required
to make operational the 3rd PCIe line that use the USB2 Serdes for PCIe
operations.
(cherry picked from commit 7afc2da3fc)
[ fix conflict errors, add missing Kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some SoC might use the Serdes for the second USB port as a 3rd PCIe
line (with the SSTR register correctly setup).
Add the node for the 3rd PCIe card and enable for the eMMC RFB board.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 2fae199953)
Backport a patch fixing a kernel panic on airoha_hw_init fail. This
should better handle scenario with NPU load Probe deferring.
(cherry picked from commit c3c75d0e68)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport cleanup patch for Airoha Ethernet patch to permit easier
backport in the future.
Automatically refresh all affected patch.
(cherry picked from commit 2f3ea18f91)
[ fix conflict errors, drop upstream patch ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Airoha AN7581 eMMC RFB board mount 2 Aeonsemi AS21xxx PHY. One is
usually connected to GDM4 and the other is optionally connected to GDM2.
Add the relevant nodes to support the one connected to GDM4.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 26da4bf552)
Pack the BL2 and BL31+U-Boot artifacts as Airoha AN7581 is currently
supported in upstream U-Boot and bootloader files can be used for
unfused boards.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17cb69fe7f)
Backport additional patch required for NPU support of Airoha AN7583.
These are specific for the NPU module with some minor fixes and to adds
upport for loading the specific Airoha AN7583 NPU firmware.
(cherry picked from commit 8b4adfbb87)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add relevant nodes for NPU support for Airoha AN7583 and enable the
kernel config to enable support in the Airoha Ethernet driver.
NPU firmware is scheduled to be upstreamed to linux-firmware and will be
added once present upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 8758b58f25)
Fix the current image Makefile for Airoha AN7583 by dropping the
artifacts entry for bootloader and add default PKG for the PHY mounted
on the RFB boards.
The artifacts for the bootloader will be readded later once ATF-A
support will be pushed mainline.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a7964f0893)
While adding support for Airoha AN7583, it was forget to push the EMMC
DTS while defining the variant in the image Makefile.
Add the missing DTS to fix image creation error.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6fe65d404b)
On the Airoha AN7583 EVB there are 2 Aeonsemi AS21xxx PHY but only the
one connected to Serdes Ethernet is usable as the other connected to
Serdes PON is not actually HW connected (as the serdes is connected to
the BOSA port)
Add comments and disable the relevant PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit ea850b5a18)
Backport upstream patch for AN7583 Ethernet support. While at it also
backport some additional fixes required to apply the AN7583 patches
cleanly.
Refresh all affected patch automatically (aside from the XSI patch that
changed the implementation)
Link: https://github.com/openwrt/openwrt/pull/20489
(cherry picked from commit 46a454fb9b)
[ fix conflict errors ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add missing syscon compatible for scuclk node.
Fix the unit-address of the scuclk node.
This fixes the pcs driver error:
airoha-pcs 1fa08000.pcs: probe with driver airoha-pcs failed with error -22
airoha-pcs 1fa09000.pcs: probe with driver airoha-pcs failed with error -22
Fixes: c3d70b1 ("airoha: en7581: Add support for external PHY")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20190
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a30daf8a0b)
Introduce initial support for Airoha AN7583 SoC and add all the required
patch for basic functionality of the SoC.
Airoha AN7583 is based on Airoha EN7581 SoC with some major changes on
the PHY handling and Serdes. It can be see as a lower spec of EN7581
with modern and simplified implementations.
All the patch are sent upstream and are pending revision. Support for
PCIe and USB will come later as soon as DT structure is accepted
upstream.
(cherry picked from commit c5b12fc02a)
[ fix conflict errors, add MDIO_AIROHA config ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This add a pending version of the Airoha PCS driver to add support for
External PHY. The Airoha PCS driver will receive some minor modification
once we the PCS subsystem will be defined upstream.
Add all the required node for GDM2 and GDM4 and enable the PCS config.
(cherry picked from commit c3d70b1ae5)
[ fix conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
No functional changes intended.
Fixes warning:
/linux/arch/arm64/boot/dts/airoha/en7581-gemtek-w1700k.dtb: i2c1@1fbf8100 (mediatek,mt7621-i2c): status: 'oneOf' conditional failed, one must be fixed:
['disable'] is not of type 'object'
'disable' is not one of ['okay', 'disabled', 'reserved', 'fail', 'fail-needs-probe']
from schema $id: http://devicetree.org/schemas/dt-core.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20131
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3872e9d317)
The baud rate control on Airoha does not function properly. This
patch enables the inactive code responsible for this. The UART2
baud rate is correct. HSUART3 operates at twice the requested
baud rate. The same problem exists in the current code, so this
doesn't introduce any regression. Support for baud rates higher
than 460800 is still required. This will be added in the future.
Tested on Gemtek W1700k. UART2 and HSUART3 are working fine.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/20049
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 440b85f5b1)
[ solve conflict error ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport fixes for Airoha pinctrl driver for PHY LED and MDIO bus. This
fix a copy-paste error for PHY LED and a misconfiguration for MT7530
embedded Switch MDIO bus GPIO pin to permit usage of external PHYs.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 35ff70e807)
Major backport of upstream patch for support of multiple feature of the
Airoha Ethernet driver.
Feature backported are TSO, Jumbo packet, Offload and initial Wlan
Offload support.
Link: https://github.com/openwrt/openwrt/pull/19816
(cherry picked from commit 9d3009f426)
[ add missing kconfig flag ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace thermal patch with upstream version. The thermal maintainer
reported that the sysfs entry are considered deprecated and that slope
and offset should be handled internally to the driver.
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a713260966)
This board is also as known as E-Life ETR631-T/ETR635-U.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB DDR3
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain telnet access:
1. Login into web interface, and download the configuration.
2. Uncompress the configuration:
* Enter fakeroot if you are not login as root.
tar -zxf <filename>.tar.gz
3. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
4. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
5. Repack the configuration:
tar -zcf backup.tar.gz etc/
6. Upload new configuration via web interface, now you can connect to
KOMI A31 via telnet.
Flash instructions:
1. Connect to KOMI A31, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-konka_komi-a31-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-konka_komi-a31-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20357
(cherry picked from commit 8a7de107d8)
[rebase uboot patches upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20595
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now we have switched to upstream implementation, this hack can go.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit fa7ec775c1)
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
(cherry picked from commit afdf88b9a1)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/20258
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
If the environment variable `CI` is set, ccache will enable the CMake
option CCACHE_DEV_MODE by default. This leads to differing behaviour
between local and CI builds which takes quite some time to debug. 🤯
Achieve consistent behaviour between local builds and CI builds by
setting CCACHE_DEV_MODE. Set it to OFF, because CCACHE_DEV_MODE amongst
other settings like linker choice, enables -Werror, which will lead to
potential compilation failures when the host compiler is updated. Using
-Werror for host utils is not desirable, because the compiler version
used is not controlled by the OpenWrt build system and host utils should
compile successfully on an as wide range of host OSes as possible.
Reported-by: Roman Azarenko <roman.azarenko@iopsys.eu>
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/20290
(cherry picked from commit 6f32c657db)
Link: https://github.com/openwrt/openwrt/pull/20334
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 143cfd6113)
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit afdf88b9a1)
[rebased upon 24.10 branch]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
- Change line endings to LF for uboot defconfig
- Drop unneeded {rx,tx}-internal-delay-ps props
- Sort UBOOT_TARGETS and dts nodes
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 61e848f7f9)
With further investigation it was found a race in generating .itb images
that include a RootFS caused by the mkits.sh and the mkimage.
Due to the fact that mkits.sh generates a .pagesync image of the passed
rootfs, it can happen that, concurrently, mkimage can be called at the
same time mkits.sh is creating another .pagesync for the same rootfs.
This cause mkimage to use an half made rootfs.pagesync creating a
corrupted image.
To address this, also protect the mkimage with the same lock used for
mkits.sh preventing any kind of concurrent usage/generation of the
rootfs.pagesync blob
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Link: https://github.com/openwrt/openwrt/pull/20492
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3de1bbd5ae)
Update mhz to latest version to include new calibration features.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit fb8a72921c)
Hardware specification:
SoC: RockChip RK3568
Flash: 32GB EMMC
RAM: 4GB DDR4
Ethernet: 2x 10/100/1000 Mbps
LED: Status (blue) Net (blue) Power(blue)
WiFi: M.2 E-key or minipcie wireless card
Button: Reset
USB: 1x USB 3.0 port
HDMI: 1x HDMI display port
LCD: 1x SPI LCD Display port
Power: DC 12V 1.5A
For TF card:
Use TF card burning tools such as balenaEtcher to flash the image
onto the tf card.
For Emmc:
To flash the device using the official RK flashing tool, RKDevTool,
in conjunction with a customized miniLoader.bin, please follow the
steps below:
Launch RKDevTool and set the load address to 0x00000000. Select the
miniLoader.bin file, then press and hold the flashing key. Connect
the power supply and power on the device to enter MARSROM mode.
Click the RUN button in RKDevTool to initiate the flashing process
for miniLoader.bin. Wait for the operation to complete and for the
device to reboot into MASKROM mode.
After successfully loading miniLoader.bin, retain the address setting
at 0x00000000 in RKDevTool. Extract the target firmware image file,
then select the decompressed .img file in RKDevTool. Click RUN to
begin the flashing process. Upon successful completion, the device
will automatically restart.
Signed-off-by: KCrO <2209352301@qq.com>
[warp commit message for every 70 chars]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit edf9154f6d)
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a947be41b7)
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4724331d70)
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 02d3aa72bb)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8cb7919a13)
Currently, ls-rcw package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-rcw' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-rcw package in DEVICE_PACKAGES lets select it when
layerscape/armv7 target is selected.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 598a0556b7)
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv8_64b.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c04eaad12a)
Currently, ls-ddr-phy package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-ddr-phy' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-ddr-phy package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8a28ddafe7)
Currently, ls-dpl package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-dpl' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-dpl package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 84437eeec0)
Currently, ls-mc package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~ls-mc' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the ls-mc package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2fb3efda0a)
Currently, fman-ucode package is being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~fman-ucode' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the fman-ucode package in DEVICE_PACKAGES lets select it when
layerscape/armv8_64b target is selected.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 22f02beaab)
Currently, tfa-layerscape packages are being included in the individual
profile DEVICE_PACKAGES but using the feature that allows skipping their
inclusion in the end image package list if prefixed with a tilde(~) which
was added in:
377b66990b ("build: introduce support to declare skip package")
But it not added to Image Builder so currently trying to build layerscape
device images in Image Builder will fail with:
ERROR: '~trusted-firmware-a-ls1012a-frdm' is not a valid world dependency, format is name(@tag)([<>~=]version)
So, instead of having to rely on support for skipping package installation
and declaring the individual TFA packages in DEVICE_PACKAGES we can just
do what other targets do and set BUILD_DEVICES so that TFA packages are
automatically set.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 03ab770da5)
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4a7de50769)
The imagebuilder is not intended to build initramfs images. Some
profiles attempt to do this and succeed, due to buildroot leaking
the initramfs-kernel into staging_dir; others attempt it, but fail
due to not having initramfs binaries present in the imagebuilder.
Fix this by adding an explict guard around the unsupported generation
of the initramfs images. This saves space and time during imagebuilder
runs, fixes those that are currently broken and protects against future
breakage for profiles that inadvertently work now.
Fixes: https://github.com/openwrt/openwrt/issues/20151
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20347
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f6e0f57be0)
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No 'PKG_CPE_ID' is stored for the kernel package Makefile. This commit
adds this.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
(cherry picked from commit 112f594042)
A lot of recent commits in odhcpd main branch are structural/semantic
changes, so instead of adding those changes to 24.10 branch it's better
to focus on the fixes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
b14cf98 router: log “Sending a RA on lan” at LOG_DEBUG
c2810fe odhcpd: update cmake file
8c2c065 odhcpd: convert README to markdown
3b96480 odhcpd: allow the use of an alternative cfg file
7328bfe odhcpd: remove confusing #defines
cdb9e5b odhcpd: improve RFC9096 § 3.5 SLAAC compliance
RFC9096 § 3.5 SLAAC compliance introduces a new config option (odhcpd
piofolder), which may wear out the flash under certain conditions (for
example: ISPs with dynamic IPv6 prefixes which disconnect the clients
every X hours).
Therefore, setting "dhcp.odhcpd.piofolder" to persistent storage in the
router flash is not advisable and should be set to other kinds of
persistent storage such as USBs, SDs, NVMEs...
In order to prevent wearing out the router flash it's set to ephemeral
storage by default (tmp):
uci set dhcp.odhcpd.piofolder="/tmp/odhcpd-piofolder"
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit ea79b5875a)
2859741d971e dhcpv4: store reqopts as uint8_t
6d342cc03bf7 odhcpd: add DNR (RFC 9463) support
c89b8b3f2ff3 odhcpd: make the IPv6 RA DNR lifetime configurable
066b3dc6ec1a netlink: fix a memory leak
171140e90b6a odhcpd: add a helper function for addr6/prefix parsing
5585b969c18f router: move pref64 calculations to the config stage
4308384748be dhcpv6: add ipv6 pxe support
6e1ad492cef5 router: replace ssize_t with size_t
Signed-off-by: David Härdeman <david@hardeman.nu>
Link: https://github.com/openwrt/openwrt/pull/20022
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit a6da0e0d37)
b462895d3157 lua: CMakeLists: drop redundant cmake_minimum_required
f247c18f8a55 examples: CMakeLists: drop redundant cmake_minimum_required
83a70399030d github: add CI build
d31effb4277b ubusd: Fix out of bounds access in event register message
d95837b1b143 ubusd: acl: compare uid/gid instead of user/group strings
b81257bb20dd ubusd: load extra group IDs for a client process
7d7b45fea05b add debian/ directory
aa4a7ee1d341 ubusd: fix more instances of missing length checks for patterns
60e04048a0e2 ubusd: fix ACL check for receiving events
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4b907e69ea)
2b69c9859946 examples: CMakeLists: update cmake minimum required version to 3.10
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 88fe81bb0c)
Current PKG_MIRROR_HASH is wrong, but it went unnoticed, because the
tarball is being fetched from @OPENWRT project mirrors. Can be
reproduced with:
make package/ebtables/{download,check} FIXUP=1 DL_DIR=/tmp PKG_MIRROR_HASH=''
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/20322
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7d4edb21b6)
Use the copy_from_user() and copy_to_user() functions for accessing
memory provided by the user in the ptm netdev iotls.
In addition also check for root permission before executing ioctl.
Suggested-by: Stanislav Fort from Aisle Research
Reported-by: Stanislav Fort from Aisle Research
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2a76abc544)
NULL and fixed addresses are constant, const qualifier are useless.
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:47:1: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
47 | const void (*ifx_bsp_basic_mps_decrypt)(unsigned int addr, int n) = NULL;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:246:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
246 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf0017c4;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:249:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
249 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf001ea4;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:252:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
252 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf001f38;
| ^~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ac8e876a6e)
Signed-off-by: Nora Matthias Schiffer <neocturne@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/20440
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PCI_IRQ_LEGACY was renamed to PCI_IRQ_INTX for kernel 6.10. Fix
compilation error:
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/vrx518_ep-2.1.0/ep.c:469:69: error: 'PCI_IRQ_LEGACY' undeclared (first use in this function); did you mean 'NR_IRQS_LEGACY'?
469 | err = pci_alloc_irq_vectors(pdev, nvec, nvec, PCI_IRQ_MSI | PCI_IRQ_LEGACY);
| ^~~~~~~~~~~~~~
| NR_IRQS_LEGACY
Signed-off-by: Andre Heider <a.heider@gmail.com>
Co-authored-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit e80dfdb6c5)
Signed-off-by: Nora Matthias Schiffer <neocturne@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/20440
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building against recent kernel versions (noticed with 6.12) and -Werror
can fail because a macro MAX(a,b) is already defined in minmax.h or
kernel.h before 5.10.
Initially noticed on 6.12, but it now happens after the kernel bump to
6.6.109 as well (upstream commit 6183c65)
In file included from ../mwlwifi-2025.02.06~db97edf2/hif/fwcmd.h:23,
from ../mwlwifi-2025.02.06~db97edf2/core.c:25:
../mwlwifi-2025.02.06~db97edf2/hif/hostcmd.h:1124: error: "MAX" redefined [-Werror]
1124 | #define MAX(a, b) (((a) > (b)) ? (a) : (b))
| ^~~
In file included from usr/include/mac80211-backport/linux/minmax.h:4,
from ./include/linux/kernel.h:27,
from usr/include/mac80211-backport/linux/kernel.h:3,
from ./include/linux/skbuff.h:13,
from usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from usr/include/mac80211-backport/linux/etherdevice.h:3,
from ../mwlwifi-2025.02.06~db97edf2/core.c:18:
./include/linux/minmax.h:315: note: this is the location of the previous definition
315 | #define MAX(a, b) __cmp(max, a, b)
| ^~~
Add a pending upstream patch which replaces the MAX(a,b) macro to avoid
conflicts and allow compilation with 6.12 backports
(cherry picked from commit 822bceb1d1)
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/20420
Signed-off-by: Robert Marko <robimarko@gmail.com>
This includes the following commits from upstream Linux between 6.12.44
and 6.12.52:
```
$ git log --reverse --oneline v6.12.44...v6.12.52 -- drivers/net/wireless/ net/mac80211/ net/wireless/
5b7ae04969f8 wifi: cfg80211: fix use-after-free in cmp_bss()
3e789f8475f6 wifi: brcmfmac: fix use-after-free when rescheduling brcmf_btcoex_info work
d9f2fb6a2ac8 wifi: mt76: mt7925: fix locking in mt7925_change_vif_links()
1fb26fd3f601 wifi: mt76: prevent non-offchannel mgmt tx during scan/roc
2aef3667e6b0 wifi: mt76: free pending offchannel tx frames on wcid cleanup
e4d5a5fc61fd wifi: mt76: fix linked list corruption
c2e32ac3f107 wifi: iwlwifi: uefi: check DSM item validity
609a8ffff5a0 wifi: ath11k: fix group data packet drops during rekey
cedbbba8a8e8 wifi: cw1200: cap SSID length in cw1200_do_join()
92bedee7168d wifi: libertas: cap SSID len in lbs_associate()
31229145e6ba wifi: cfg80211: sme: cap SSID length in __cfg80211_connect_result()
06616410a3e5 wifi: mwifiex: Initialize the chan_stats array to zero
a001c2f6a40c wifi: mt76: mt7925u: use connac3 tx aggr check in tx complete
eefa2ad9009b wifi: mt76: mt7996: Initialize hdr before passing to skb_put_data()
089fd41902ee wifi: mt76: mt7925: fix the wrong bss cleanup for SAP
26618c039b78 wifi: ath11k: update channel list in reg notifier instead reg worker
fa4abd439f27 wifi: ath11k: update channel list in worker when wait flag is set
2203ef417044 wifi: wilc1000: avoid buffer overflow in WID string configuration
32adb020b0c3 wifi: mac80211: increase scan_ies_len for S1G
8df33f4d4a0b wifi: mac80211: fix incorrect type for ret
79dc6d4932de wifi: virt_wifi: Fix page fault on connect
1f52119809b7 wifi: ath11k: fix NULL dereference in ath11k_qmi_m3_load()
895cccf639ac wifi: rtw89: fix use-after-free in rtw89_core_tx_kick_off_and_wait()
914d02595ba6 wifi: rtlwifi: rtl8192cu: Don't claim USB ID 07b8:8188
1713796d6538 wifi: rtl8xxxu: Don't claim USB ID 07b8:8188
```
Removed ath11k/940-ath11k-Revert-clear-the-keys-properly-when-DISABLE_K.patch
This problem is fixed by:
609a8ffff5a0 wifi: ath11k: fix group data packet drops during rekey
Link: https://github.com/openwrt/openwrt/pull/20311
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since we provide spi-nor image for this device, use lzma for
smaller size.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 7fe15f84c7)
This is a smart door lock device equipped with OpenWrt 14.07 OEM
modified version Qdwrt
The OEM has closed down, This commit is intended to maximize the
remaining value of these devices. It can flash OpenWrt to become
an AP
Specification:
- SoC: MediaTek MT7628NN
- Flash: 8 MB
- RAM: 64 MB
- Power: DC 5V - 25V
- Ethernet: 1 x RJ45 (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- On-Board LED:
Status 1: GPIO/43 active-low
Status 2: GPIO/44 active-low
Power: AlwaysOn
- Button:
WPS / RESET: GPIO/14 active-low
- Bluetooth: CC2541 via UART1 (ttyS1) and GPIO/26-29
- RFID: MF RC522 on I2C@28
- RTC: DS1339 on I2C@68
- Shell (via CON1 cable)
- LED (Swipe card area):
- Green GPIO/3 active-high
- Red GPIO/11 active-high
- Matrix keypad: (active-low)
GPIO/20 GPIO/21 GPIO/19 (Rows)
GPIO/24 1 2 3
GPIO/25 4 5 6
GPIO/22 7 8 9
GPIO/23 BACK 0 ENTER
(Cols)
- UART: 1 x UART on PCB - 57600 8N1
- GPIO Relay: GPIO/42 active-high
- GPIO Buzzer: GPIO/15 active-high
Warning:
The original firmware does not use the device tree.
This device tree is written based on the content of /sys/devices/platform
and has been tested
Note:
- On the device, matrix keypad rows actually are columns, and the columns actually are rows
- The key code of the CLEAR key of the matrix keypad is BACK in the original firmware.
Issue:
- No drivers in mainline kernel for RFID and Bluetooth.
Flash Instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 10.10.10.1 with root password "szqdingnet123" (SSH Port 22, Telnet Port 9900)
3. Download openwrt firmware on the computer.
4. Setup a http server on computer. And use wget download openwrt firmware from computer
5. Use command "mtd -r write openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin firmware"
to flash
Using U-Boot WebUI:
1. Configure PC with a static IP address 10.10.10.2/24.
2. Open http://10.10.10.1
3. Use "mkqdimg -B qc202 -f openwrt-ramips-mt76x8-qding_qc202-squashfs-sysupgrade.bin" to
make image.
4. Upload factory.bin via U-Boot WebUI.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-qianding-smart-locker-and-flash.html
Original U-Boot firmware image tools:
https://gitlab.com/CoiaPrant/mkqdimg
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17471
(cherry picked from commit b2f814fed4)
Link: https://github.com/openwrt/openwrt/pull/20159
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
According to the MT7628 hardware datasheet:
- GPIO/4 was originally used for I2C, but is now used as the Modem Power.
- GPIO/5 was originally used for I2C, but is now used as the SIM card select. (n/a for this device)
- GPIO/6 was originally used for SPI CS1, but is now used as the Serial mode switch.
- GPIO/36 was originally used for PERST, but is now used as the GPS OE. (n/a for this device)
- GPIO/38 was originally used for WDT, but is now used as the Modem2 Power. (n/a for this device)
- GPIO/44 was used for WLED_AN, but is now controlled by `gpio-leds`.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/20256
(cherry picked from commit 44c79d094f)
Link: https://github.com/openwrt/openwrt/pull/20257
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since there's no plan to backport video support for RK3588, drop this
unused driver.
This reverts commit 08b6454d66.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Backport support for 1024 MPDU TX aggregation in EHT from upstream
kernel. Without this fix, TX performance on WiFi-7 links
is severely limited, making the link practically unusable.
Signed-off-by: Oliver Sedlbauer <osedlbauer@tdt.de>
Make sure that the package gets updated after the last fix.
Fixes: 9d83c1b1a9 ("uqmi: fix data-format parsing")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0203ef3fc9)
wda-get-data-format now returns an object instead of a single string.
Account for this change when reading the packet data format.
Suggested-by: Sebastian Ertz (https://github.com/sebastianertz)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cd20ae44f2)
No need to modify default min/max cpufreq as upstream opp-table
handles it perfectly already.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 7203470378)
This commit updates the existing patch for RFC 9096 compliance in odhcpd with the following improvements:
- The router lifetime calculation is corrected to align with RFC 9096, with the default lifetime changing to 2700 seconds.
- The RDNSS and DNSSL lifetime is now based on the highest valid lifetime of advertised prefixes, as recommended by RFC 9096.
These changes should help to mitigate issues with Android devices where IPv6 addresses are lost during idle periods.
Signed-off-by: Aviana Cruz <gwencroft@proton.me>
(cherry picked from commit 9084f49725)
The version of libxml2 was bumped from 2.13.6 to 2.14.5. Since version
2.14, libxml2 is not binary compatible with older versions. Therefore
add an abi version.
From the NEWS file:
Binary compatibility is restricted to versions 2.14 or newer. On ELF
systems, the soname was bumped from libxml2.so.2 to libxml2.so.16.
Signed-off-by: Jan Kardell <jan.kardell@telliq.com>
Link: https://github.com/openwrt/openwrt/pull/19983
(cherry picked from commit 420be05d90)
Link: https://github.com/openwrt/openwrt/pull/19985
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3GHz
- RAM : DDR3 256Mbytes, ESMT M15T2G16128A
- Flash : 128Mbytes NAND Flash, ESMT F50L1G41LB
- WLAN : MediaTek MT7976CN dual-band Wi-Fi 6
- 2.4GHz : b/g/n/ax, MU-MIMO
- 5GHz : a/n/ac/ax, MU-MIMO
- Ethernet : MediaTek MT7531AE
- LAN : 10/100/1000 Mbps x4
- WAN : 10/100/1000 Mbps x1
- UART : 1x4 pin header on PCB
- [J6] TX, RX, GND, 3.3V (115200, 8N1)
- Buttons : WPS, Reset
- LEDs : 1x CPU (Amber)
1x Wi-Fi 5GHz (Amber)
1x Wi-Fi 2.4GHz (Amber)
1x WAN activity (Amber)
4x LAN activity (Amber)
- Power : 12VDC, 1A (Center positive polarity)
MAC address
-----------
+-----------+-------------------+-----------------------+
| Interface | MAC | Algorithm |
+-----------+-------------------+-----------------------+
| WLAN 2.4G | B0:38:6C:48:xx:xx | label |
| WLAN 5G | B2:38:6C:48:xx:xx | label with LA Bit Set |
| WAN | B0:38:6C:48:xx:xx | label + 1 |
| LAN | B0:38:6C:48:xx:xx | label + 3 |
+-----------+-------------------+-----------------------+
The WLAN 2.4G MAC was found in 'Factory' partition, 0x4
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Replace a file in the OEM recovery software with the file from step 2
7. Run the OEM recovery software and follow the instructions
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19368
(cherry picked from commit aea6d1bf5e)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes compilation of the vmmc driver, it uses these functions.
Fixes: c676281e7e ("kernel: bump 6.6 to 6.6.103")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 6690f551c8)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
(cherry picked from commit 18925614c0)
Link: https://github.com/openwrt/openwrt/pull/19940
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds the capability to flash the factory image using the OEM recovery
software, ipTIME Firmware Wizard(11ac).
Installation
------------
1. Download the OEM recovery software from the manufacturer's website
2. Download the *squashfs-factory.bin file from the OpenWrt website
3. Press a reset button, and power up the router(keep pressing the reset button)
4. Wait more than 10 seconds until the CPU LED stop blinking
5. Connect the router(LAN port) to the PC
6. Run the OEM recovery software and follow the instructions
7. Select the *squashfs-factory.bin file during the router recovery process
8. Wait for the router to boot from *squashfs-factory.bin
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19497
(cherry picked from commit 0e4a69e340)
Signed-off-by: Donghyun Ko <nyankosoftware@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19928
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport a patch from upstream kernel 6.17-rc4 which fixes a regression
introduced in the latest stable kernel versions.
This is already in the Linus stable queues for the next minor kernel
updates.
Fixes: 1c92e468d5 ("kernel: bump 6.6 to 6.6.103")
Fixes: f39c7e103f ("kernel: bump 6.12 to 6.12.43")
Reported-by: Goetz Goerisch <ggoerisch@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c589fb7baf)
Other than most boards with DDR3 the TP-Link 7DR7230 v2 cannot use
the "comb" DDR calibration option and needs only the "ddr3" option
set instead.
Build TF-A to boot with mtk_uartboot for MT7988 with DDR3 RAM.
Signed-off-by: gns <infiwang@pm.me>
(cherry picked from commit fea5962755)
Other than most boards with DDR4 the ASUS ZenWiFi BT8 cannot use the
"comb" DDR calibration option and needs only the "ddr4" option set
instead.
Build TF-A SPIM-NAND with UBI as well as to boot from RAM with
mtk_uartboot for MT7988 with DDR4 RAM.
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit e17856c9ef)
8b320f9 ucode: adjust for new ext resource type
e61d2be sys: use strstr() to detect installed packages
bba9519 rpc-sys: packagelist: don't truncate input lines on read
The removed patch was applied upstream.
Link: https://github.com/openwrt/openwrt/pull/19919
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.
Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks
Signed-off-by: Dim Fish <dimfish@gmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 94f043bf87)
The Xiaomi AX3000T has two hardware revisions. One uses MT7531
switch, and the other uses AN8855 switch. Set "mediatek,switch"
property to "auto" to be compatible with different switches.
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit b85c5f6817)
This patch series will provide better support for Mediatek
ethernet and add support for Airoha AN8855.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 24ade65ab5)
RTL83xx devices have two types of receive interrupts for each of its
8 rings. One for packet received and another for ring overflow. When
the switch is flooded with incoming packets the receive handler will
disable the packet receive notification but still keeps the overflow
notification enabled. While the receive path "slowly" processes the
received packets each new packet triggers the overflow IRQ again. The
device becomes unresponsive and eventually produces messages like:
[18441.709764] rcu: Stack dump where RCU GP kthread last ran:
[18441.727892] Sending NMI from CPU 1 to CPUs 0:
[18441.742300] NMI backtrace for cpu 0 skipped: idling at 0x8080e994
[18415.251700] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[18415.271350] rcu: 0-...!: (0 ticks this GP) idle=d740/0/0x0 ...
[18415.303046] rcu: (detected by 1, t=6004 jiffies, g=230925, ...
[18415.326095] Sending NMI from CPU 1 to CPUs 0:
[18415.340540] NMI backtrace for cpu 0
Fix this issue by always disabling receive and overflow interrupts at
the same time.
Test with hping3 --udp -p 5021 -d 1400 --flood 192.168.2.72
Before (3sec run):
[183260.324846] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x101, mask: 0x7ffeff
[183260.340524] rtl838x-eth 1b00a300.ethernet eth0: RX buffer overrun: status 0x1, mask: 0x7ffeff
[183260.345799] net_ratelimit: 489997 callbacks suppressed
After (3 sec run):
[ 373.981479] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 374.031118] rtl838x-eth 1b00a300.ethernet eth0: rx ring overrun: status 0x101, mask: 0x7fffff
[ 377.919996] net_ratelimit: 34 callbacks suppressed
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19365
(cherry picked from commit 963ee6ac3f)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19891
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IgniteNet SunSpot AC Wave2 comes with 2x QCA9994 ath10k chips
connected to the IPQ8068 SoC via PCIe.
Add board-2.bin for both radios on this board.
3ac4a64 qca9984: add BDFs for IgniteNet SS-W2-AC2600
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d8303b4721)
Link: https://github.com/openwrt/openwrt/pull/19902
[Do not add ignitenet_ss-w2-ac2600]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have modified the kernel to setup all "default" consoles,
including serial ports and framebuffers/screens, providing
no console= argument is supplied on the kernel command line.
Adding 'console=tty1' caused the 'default' serial port on
device tree systems to break, as the kernel would not carry
over the settings (like baud rate) from the bootloader.
The system administrator can still force the use of a
specific console by adding their own console= arguments.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("armsr: use console=tty1 to make
console more readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit bff179de73)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A previous change added 'console=tty1' to the default kernel command
line on armsr, in order to ensure the framebuffer console is enabled
on systems capable of graphics output.
Unfortunately, this change broke boards that used device tree
(DT) firmware with serial consoles, as the serial console
specified by the system firmware (stdout-path) was no longer
setup by the kernel.
A bit of probing determined that the SPCR (serial port console
direction table) on ACPI systems was preventing Linux from setting
up a default framebuffer console on these systems (which is why
console=tty1 was added).
(The affected ACPI systems are usually VMs using QEMU's
'virt' machine and EDK2 firmware. The firmware on these systems
does not remove the SPCR when a screen is present)
So to ensure all possible systems are setup correctly, we modify
the kernel so all "default" console types (serial and screen)
are setup when no console= arguments are specified on the kernel
command line.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("use console=tty1 to make console more
readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3697022ce3)
Link: https://github.com/openwrt/openwrt/pull/19894
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6e4ffe2c6657 ucode: add function for getting the number of entries in a snapshot
a62edd89255b ucode: add support for fetching kernel tracepoint events
edeb4d6dc690 udebug-cli: add support for streaming tracing data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 78188ee2bc)
3d953628bf17 udebugd: add support for setting an override config
93f6df0240e5 udebug-cli: add support for overriding config on the command line
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c4e7b9b9b7)
The vendor DTS defined incorrect GPIOs for the LEDs, which caused them
to not function properly. Initially, the WAN, WLAN LEDs appeared to
work, but further testing showed that they were non-functional.
This patch corrects the GPIO assignments in the DTS, restoring full LED
functionality including blinking, except the power LED which cannot be
software controlled.
Tested on a CF-EW71 v2 unit.
Fixes: ee3a6adc6c ("ath79: add support for Comfast CF-EW71 v2")
Signed-off-by: Felix Golatofski <git@xdfr.de>
Link: https://github.com/openwrt/openwrt/pull/19665
(cherry picked from commit 9ce23ac840)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is some confusion in the Git log of this file. Specifically,
the commit message on 7b7f1702 incorrectly indicates that there was
"potential fear" about copyright infringement.
Upon review of this situation, there is, in my opinion, no concern of
copyright infringement here. This is not legal advice; it is my
opinion based of years of work on copyright policy for FOSS.
However, Elliott Mitchell's idea was obviously helpful as inspiration
in writing this script and deserves credit. Ideas alone, however,
are not to my knowledge copyrightable anywhere in the world.
Signed-off-by: Bradley M. Kuhn <bkuhn@sfconservancy.org>
(cherry picked from commit d8e738e5c4)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
(cherry picked from commit 6889ea7b9a)
Link: https://github.com/openwrt/openwrt/pull/19839
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
PR of openwrt:main: https://github.com/openwrt/openwrt/pull/19512
OpenFi 6C is a portable Wi-Fi 6 travel router based on MediaTek MT7981B+MT7976CN.
Two slightly different versions have been sold. The V1 board has a green color and lacks the modem LED. The V2 board is black and has a LED for the modem.
Specifications:
- SoC: MediaTek MT7981B (Filogic 820) 1.3GHz dual-core ARM Cortex-A53
- RAM: 1GB DDR4
- Flash: 256MB SPI NAND
- Wireless: 2.4GHz/5GHz 802.11ax
- Ethernet: 1x 10/100/1000M LAN
- USB: 1x USB 3.0 Type-A port
- Expansion: M.2 slot for 5G modem
- Cooling: PWM-controlled fan
- Buttons: Reset, Mode switch
- LEDs: System, Ethernet, 5G WiFi, Modem status
**Installation via U-Boot web page**
1. Set static IP 192.168.21.2/255.255.255.0 on your computer.
2. Connect to the Ethernet port and hold the reset button while booting the device. Wait for 6-8 seconds, and release the reset button.
3. Open U-boot web page on your browser at http://192.168.21.1
4. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
5. Wait for automatic reboot.
**Installation via sysupgrade**
Flash the sysupgrade file via LuCI upgrade page without saving the settings.
Signed-off-by: Jiasheng Zhu <newbanyaya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19512
(cherry picked from commit 536a25ebf8)
Link: https://github.com/openwrt/openwrt/pull/19536
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt SNAPSHOT OEM
customized version
WARNING: The original firmware device tree is modified from evb
boards, and the device tree name is evb board. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7628NN
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN [slot not install], 1x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only [antenna not install]
- LED:
System/Power (RUN): GPIO/37 active-low
Modem: GPIO/3 active-low
RF (Modem Signal): GPIO/2 active-low
- Button:
WPS / RESET: GPIO/11 active-low
- UART: 1x UART on PCB - 115200 8N1
- Serial / COM: 1X RS232/RS485 on board (GPIO/6 hi:RS485 lo:RS232)
- GPIO Watchdog: GPIO/0 mode=toggle timeout=1s
- Modem: 1x Built-in modem on board (Power: GPIO/4 active-high)
- PCIe: 1x miniPCIe for modem [slot not install]
- SIM Slots: 1x SIM Slots
Issue:
- Factory partition not store mac address on original firmware
Flash instruction:
Using SSH/Telnet:
1. Connect the board to the computer via RJ45 Ethernet
2. Login 192.168.8.1 with root password "superzxmn" (SSH Port 22, Telnet Port 5188)
3. Download openwrt firmware on the computer.
4. Use scp or sftp put firmware to board /tmp
5. Use command "mtd -r write openwrt-ramips-mt76x8-hongdian_h7920-v40-squashfs-sysupgrade.bin firmware"
to flash
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h7920-v40-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
(cherry picked from commit ebee946227)
Link: https://github.com/openwrt/openwrt/pull/19716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backpot upstream patch for Flow Offload support for AN7581 and refresh
all affected patch. To correctly work a dedicated firmware is needed to
use the dedicated Network Coprocessor (NPU).
This also introduce good cleanup and moves the driver in a dedicated
Airoha directory. While currently not totally usable (due to lack of
firmware blob) this is needed to backport support for external PHY/SFP
support.
Refresh all affected patch.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Tested-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18166
(cherry picked from commit ad2077165b)
[ refresh patches ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This got added in commit 15887235, cherry-picked into the 24.10 branch
as 642b5b61 and was partially lost in a manual patch refresh in
3a2a2c99.
The main branch still contains the full set of rx DMA size changes, so I
assume it was lost by accident.
With rx.dma_size=2K, my TP-Link Archer MR600v2 (MT7621) randomly reboots
due to OOM.
Signed-off-by: Stefan Dösinger <stefandoesinger@gmail.com>
In the conversion to dts, qca,led-pin was used for both interfaces.
Unfortunately, it's mutually exclusive with gpio-controller which made
it not do anything.
Fixes: 949e1a0 ("mpc85xx: tl-wdr4900: move platform code to dts")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19758
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit cc0ff28f23)
The ath10k_sdio driver is no longer automatically loaded, which can cause `could not probe fw (-22)` errors.
Manually reload the driver after the system has finished loading using /etc/init.d/reload-sdio-wifi to resolve this issue.
Note: Do not use the automatic channel, as this may cause WiFi to not start.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
(cherry picked from commit 893695dba0)
The bootup of the armsr target sometimes failed like this:
```
[ 0.762283] NET: Registered PF_INET6 protocol family
[ 0.791987] workqueue: Failed to create a worker thread: -EAGAIN
[ 0.801986] workqueue: Failed to create a rescuer kthread for wq "mld": -EAGAIN
[ 0.964017] NET: Unregistered PF_INET6 protocol family
```
Increase the maximum number of threads the kernel allows.
Link: https://github.com/openwrt/openwrt/pull/19376
(cherry picked from commit c5330bdf7e)
Link: https://github.com/openwrt/openwrt/pull/19554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
f510d75ff7 nscd: Use time_t for return type of addgetnetgrentX
5aa4bb67b9 resolv: Fix some unaligned accesses in resolver [BZ #30750]
249646f12b Force DT_RPATH for --enable-hardcoded-path-in-tests
697ab62d11 i386: Disable Intel Xeon Phi tests for GCC 15 and above (BZ 31782)
c8cb4d2b86 misc: Add support for Linux uio.h RWF_NOAPPEND flag
712453634c s390x: Fix segfault in wcsncmp [BZ #31934]
7bfc35959d nptl: fix potential merge of __rseq_* relro symbols
d9d019d674 elf: Make dl-rseq-symbols Linux only
bb30bd2162 Linux: Make __rseq_size useful for feature detection (bug 31965)
dc512364e8 resolv: Allow short error responses to match any query (bug 31890)
6cad0f543c resolv: Do not wait for non-existing second DNS response after error (bug 30081)
1bed6acf50 resolv: Track single-request fallback via _res._flags (bug 31476)
0301637b99 linux: Update the mremap C implementation [BZ #31968]
f0e2114535 mremap: Update manual entry
6bb75212e6 Add mremap tests
3ac7ba61d2 Update syscall lists for Linux 6.5
9184c13681 resolv: Fix tst-resolv-short-response for older GCC (bug 32042)
059f82c3b9 Fix name space violation in fortify wrappers (bug 32052)
c005d1bd6f x86: Fix bug in strchrnul-evex512 [BZ #32078]
28f358bc42 support: Add FAIL test failure helper
99ffa84bdc stdio-common: Add test for vfscanf with matches longer than INT_MAX [BZ #27650]
87a1968a72 Make tst-ungetc use libsupport
804d3c8db7 ungetc: Fix uninitialized read when putting into unused streams [BZ #27821]
b9f72bd5de ungetc: Fix backup buffer leak on program exit [BZ #27821]
15ca66303f posix: Use <support/check.h> facilities in tst-truncate and tst-truncate64
f30501ca75 nptl: Use <support/check.h> facilities in tst-setuid3
370be85892 libio: Attempt wide backup free only for non-legacy code
4dd8641461 Add crt1-2.0.o for glibc 2.0 compatibility tests
fa4ad10406 elf: Change ldconfig auxcache magic number (bug 32231)
9423cc5387 nptl: initialize rseq area prior to registration
37ded328c4 nptl: initialize cpu_id_start prior to rseq registration
cf06772360 x86: Avoid integer truncation with large cache sizes (bug 32470)
5c9be512ee x86_64: Sort fpu/multiarch/Makefile
49016f2190 x86_64: Add log2 with FMA
b2a45f1eee x86_64: Add expm1 with FMA
c92946d9b2 x86_64: Add log1p with FMA
58822f954f x86: Check the lower byte of EAX of CPUID leaf 2 [BZ #30643]
7772f9358c elf: Fix slow tls access after dlopen [BZ #19924]
5a64f93365 x86: Only align destination to 1x VEC_SIZE in memset 4x loop
0d14bf0754 sysdeps/x86/Makefile: Split and sort tests
dc1762113d x86_64: Fix missing wcsncat function definition without multiarch (x86-64-v4)
04b8d48432 x86: Improve large memset perf with non-temporal stores [RHEL-29312]
12fec8aae5 x86/string: Fixup alignment of main loop in str{n}cmp-evex [BZ #32212]
48642ef1a5 elf: Avoid some free (NULL) calls in _dl_update_slotinfo
549e7f7c5a elf: Support recursive use of dynamic TLS in interposed malloc
c32fd59314 Fix underallocation of abort_msg_s struct (CVE-2025-0395)
650a0aaaff stdlib: Test using setenv with updated environ [BZ #32588]
f984e2d7e8 assert: Add test for CVE-2025-0395
9ca74b8ad1 AArch64: Improve generic strlen
95aa21432c AArch64: Optimize memset
5fe151d86a AArch64: Remove zva_128 from memset
3de5112326 math: Improve layout of expf data
52c2b1556f AArch64: Add SVE memset
097299ffa9 AArch64: Use prefer_sve_ifuncs for SVE memset
5a08d049dc math: Improve layout of exp/exp10 data
3be3728df2 elf: Ignore LD_LIBRARY_PATH and debug env var for setuid for static
454f24e981 support: Use const char * argument in support_capture_subprogram_self_sgid
4335cd9b58 support: Add support_record_failure_barrier
31fa0f73e2 elf: Test case for bug 32976 (CVE-2025-4802)
ca41fe44a5 x86_64: Fix typo in ifunc-impl-list.c.
ca7e32d024 elf: Fix subprocess status handling for tst-dlopen-sgid (bug 32987)
81f58dd9b7 support: Pick group in support_capture_subprogram_self_sgid if UID == 0
5a6276d97a Fix error reporting (false negatives) in SGID tests
1a0d73a625 pthreads NPTL: lost wakeup fix 2
b5c4727e59 nptl: Update comments and indentation for new condvar implementation
1fa5e51897 nptl: Remove unnecessary catch-all-wake in condvar group switch
44eaf0615d nptl: Remove unnecessary quadruple check in pthread_cond_wait
7625579f11 nptl: Remove g_refs from condition variables
6bac834c5a nptl: Use a single loop in pthread_cond_wait instaed of a nested loop
5765653697 nptl: Fix indentation
8899e89b29 nptl: rename __condvar_quiesce_and_switch_g1
39a80f4035 nptl: Use all of g1_start and g_signals
51210d6496 nptl: PTHREAD_COND_INITIALIZER compatibility with pre-2.41 versions (bug 32786)
879f0ee122 malloc: add indirection for malloc(-like) functions in tests [BZ #32366]
a637f2c42f malloc: obscure calloc use in tst-calloc
21019afe65 malloc: cleanup casts in tst-calloc
6a52d5cab0 posix: Fix double-free after allocation failure in regcomp (bug 33185)
Link: https://github.com/openwrt/openwrt/pull/19551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6953f19 wireless-regdb: Update regulatory info for Indonesia (ID) for 2025
2e8214e wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band for GB
a94f685 wireless-regdb: Update regulatory info for Egypt (EG) for 2024
7628ce2 wireless-regdb: Update regulatory rules for Brazil (BR) on 6GHz
4411b39 wireless-regdb: Update regulatory info for Vietnam (VN) for 2025
490f136 wireless-regdb: Update regulatory info for Estonia (EE) for 2024
c56c663 wireless-regdb: update regulatory rules for Paraguay (PY) on 6 GHz for 2025
5a8ced5 wireless-regdb: Update regulatory info for CEPT countries for 6GHz listed by WiFi Alliance
5fd8ee3 wireless-regdb: update regulatory rules for Bosnia and Herzegovina (BA) for 6 GHz
e05260a wireless-regdb: update regulatory database based on preceding changes
Link: https://github.com/openwrt/openwrt/pull/19474
(cherry picked from commit 7fe06b7f56)
Link: https://github.com/openwrt/openwrt/pull/19538
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a854d833ea)
5d10084ea885 lib-ucode.c: add #define _GNU_SOURCE
a95364b41d52 udebug-cli: fix terminating uloop
c00eb9b685a8 ucode: use FILE handle for pcap output
4265167cb6e8 ucode: add error reporting to pcap_write
4a908ee731a6 udebug-cli: stop event loop on write failure
6e04f4187231 ucode: use ucv_resource_create_ex for remote rings
c297f04e1852 ucode: drop use ucv_resource_create
f207d37a1055 ucode: add support for specifying ring format
98683a94bcdd ucode: support appending array data, similar to socket.send()
a7ecd483ed38 ucode: allow calling udebug.init() multiple times
d4a4c788c416 ucode: fix allocation size of local ring meta
184706abaf50 ucode: add timestamp argument to foreach()
8442c948c193 ucode: add function for getting ring information
f4958a4c591a ucode: add const entries for enum udebug_format
14d4fec36993 udebug-cli: add logstream command
6ed8536142bb ucode: fix entries/size confusion
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7b0ce213e9)
The PHY LED is connected to EN8811H's internal GPIO, which is unable
to be controlled by current driver.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 9e3c8c9d94)
These instructions are for 64-bit load/store. On ARMv5TE, the CPU
requires addresses to be aligned to 64-bit. When misaligned, behavior is
undefined (effectively either loads the same word twice on LDRD, or
corrupts surrounding memory on STRD).
On ARMv6 and newer, unaligned access is safe.
Removing these instructions for ARMv5TE is necessary, because GCC
ignores alignment information in pointers and does unsafe optimizations
that have shown up as bugs in various places.
This patch was originally added more than 11 years ago in commit b050f87d13,
but got lost 6 years ago, when gcc 9.1 was added in 88c07c6552.
This primarily affects the kirkwood and ixp4xx targets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c1c1112006)
**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Cherry-picked from https://github.com/coolsnowwolf/lede/commit/949d0bd77a2e97c2d982531f72b76c575fb28839
Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
(cherry picked from commit db1de8d21f)
Link: https://github.com/openwrt/openwrt/pull/19391
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The script always gets passed the package name, not the source name.
Optimize for the default case where the package name matches the
filename prefix.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 471fd0a502)
27839f854a58 ubusd: make txq_len field signed
b35b2bc63e8e ubusd: treat EACCES on write like EAGAIN
713e9d19b2b6 ubusd: retry write on EINTR
8bb523ab20e0 ubusd: fix txq_len accounting
b1b783c74742 ubusd: add another tx attempt on enqueueing the first message for a client
5952b48e251c ubusd: do not call socket callback from ubus_msg_send
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 90cd8640bd)
(cherry picked from commit d9cd67b542)
GL.iNet shipped a hardware change of the WAN PHY going from the MaxLinear
GPY211C to the Airoha EN8811H.
Signed-off-by: Matthew Bilker <me@mbilker.us>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8d30e07180)
Hardware specification:
SoC: MediaTek MT7988D 3x A73
Flash: 128 MB SPI-NAND (F50L141LB / DS35Q1GB)
RAM: 512 MB DDR4 (NT5AD256M16E4-JR)
Ethernet: 2x 1GbE (built-in), 2x 2.5GbE (built-in + Airoha EN8811HN)
WiFi: MediaTek MT7992A
Button: Reset, Mesh
Power: DC 12V 2A
UART: 3.3v, 115200n8
Flash instruction:
TP-Link locks down their firmware and serial console, so the firmware
must be flashed with mtk_uartboot.
1. Download mtk_uartboot:
https://github.com/981213/mtk_uartboot/releases
2. Open the case, and attach to the UART.
3. Start mtk_uartboot:
./mtk_uartboot -a -s /dev/ttyUSB0 -p mt7988-ram-ddr4-bl2.bin \
-f immortalwrt-mediatek-filogic-tplink_tl-7dr7250-v1-bl31-uboot.fip \
--brom-load-baudrate 921600 --bl2-load-baudrate 1500000
5. Cut off the power and re-engage, wait for UART download to complete.
6. Connect to the UART, write new BL2/FIP/Firmware with TFTP.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 94a754ac7c)
Specifications:
- SoC: Mediatek MT7622B
- RAM: 256M
- Flash: EN25QH128 16M
- Ethernet: RTL8367S 3xGE
- WiFi: MT7622 2.4G 4x4 + MT7905 5G 4x4
- UART: 3.3v, 115200n8
Flash instruction
Please refer commit 9f73519e62 ("mediatek: add support for TP-Link TL-XDR3230 v1").
This board is basically same as XDR3230 v1 so you can reuse the BL2 and FIP for it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 70564dc9ab)
This device is similar to the Cudy TR3000 v1 128MB version.
The difference is that the flash memory is 128mb and the other is 256mb
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Power: 5 VDC, 3 A
Installation:
Cudy has distributed intermediate firmware to make installation easier
1. Go to [Cudy CN official website](https://www.cudy.com/zh-cn/pages/download-center/tr3000-1-0) and download the intermediate firmware
2. Upgrade the intermediate firmware on the page
3. Visit the intermediate firmware 192.168.1.1 webpage and use the sysupgrade image to update
other:
If you fail to flash the device, you can use TFTP to flash back to the original firmware.
1. Ask Cudy CN official customer service for the original firmware
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an recovery.bin firmware file.
Signed-off-by: cheng wang <typedelta@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19167
(cherry picked from commit 594da824a4)
Link: https://github.com/openwrt/openwrt/pull/19348
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Due to a bug, USB is not powered on after boot on hAP ac.
This prevents extroot configurations from working as overlayfs is mounted
before USB device can be powered on. This commit fixes this by enabling USB
in devicetree.
Related discussion links:
- https://forum.openwrt.org/t/usb-power-is-off-on-boot/229007
---
Extroot configuration requires the USB to be powered on before
preinit_main/80_mount_root. Probably the simplest approach is to enable
it in the devicetree. Another approach would be to add a script into
/lib/preinit that will power on USB via /sys/class/gpio/usb-power/value
E.g.
cat /lib/preinit/79_power_on_usb
do_power_on_usb(){
echo '1' > /sys/class/gpio/usb-power/value
}
boot_hook_add preinit_main do_power_on_usb
Signed-off-by: Valeriy Manzhos <manzhos.va@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19149
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f7dba4ebbc)
Link: https://github.com/openwrt/openwrt/pull/19334
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 6f8c58bfd8)
[sync uboot defconfigs with 24.10 branch, change apk to opkg]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's only used inside spi_nand_read_pp, no reason to make it as a function.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit ec27c0797d)
This device is similar to the Cudy TR3000 v1 128MB version.
The difference is that the flash memory is 128mb and the other is 256mb
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Power: 5 VDC, 3 A
Installation:
Cudy has distributed intermediate firmware to make installation easier
1. Go to [Cudy CN official website](https://www.cudy.com/zh-cn/pages/download-center/tr3000-1-0) and download the intermediate firmware
2. Upgrade the intermediate firmware on the page
3. Visit the intermediate firmware 192.168.1.1 webpage and use the sysupgrade image to update
other:
If you fail to flash the device, you can use TFTP to flash back to the original firmware.
1. Ask Cudy CN official customer service for the original firmware
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an recovery.bin firmware file.
Signed-off-by: cheng wang <typedelta@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 594da824a4)
Hardware specification:
SoC: MediaTek MT7621AT
Flash: Micron MT29F2G08ABAGAWP 256Mib
RAM: 256MB DDR3
Ethernet: 3x 10/100/1000 Mbps
LED: Status (red / blue / green / white / cyan / yellow / magenta)
Switch: MediaTek MT7530
WiFi: MediaTek MT7905DAN + MT7975DN
Button: Reset (gpio 17), WPS (gpio 18)
ZigBee: EFR32MG21
Ble: EFR32BG21
USB Audio: iec958
Power: DC 12V 1.5A
Gain SSH access:
1. Login into web interface.
2. Go to http://192.168.10.1/cgi-bin/luci/admin/mtk/console (CMCC version) or http://192.168.2.1/cgi-bin/luci/admin/mtk/console (CT version)
echo -en "root\nroot\n" | passwd
4. Go to http://192.168.10.1/cgi-bin/luci/pti/ssh_open (CMCC version) or http://192.168.2.1/cgi-bin/luci/pti/ssh_open (CT version)
5. Ssh to router username:root password:root
5. Fork https://github.com/DragonBluep/uboot-mt7621
6. Compile uboot by Github action.
Flash Type : NAND
MTD Partition Table : 512k(u-boot),256k(config),256k(configdata),512k(factory),-(firmware)
Kernel Load Address : 0x180000
Reset Button GPIO : 18 #Can't use gpio 17 because it is flipped, on is off, of is on.
System LED GPIO : 14
CPU Frequency (400 - 1200) : 880
DRAM Frequency : 1200
Prefered DDR Init Parameters : DDR3-256MiB
Baud Rate : 115200
7. Check carefully everything is right.
8. Upload u-boot-mt7621.bin via scp.
9. Backup everything, especially 'Factory' part.
10. Write new uboot.
mtd write u-boot-mt7621.bin Bootloader
11. Set static IP on your PC:
IP 192.168.1.2/24, GW 192.168.1.1
12. Serve ImmortalWrt initramfs image using TFTP server. Don't forget to rename the image to "recovery.bin".
13. Cut off the power , hold wps button and re-engage, wait for TFTP recovery to complete.
14. After ImmortalWrt has booted, perform sysupgrade.
Attention: This firmware uses different boot address with https://github.com/coolsnowwolf/lede/pull/10057/commits/ecfbf648e564b058524d0ae119ba2b58b29f198a
Don't recommend to use breed, though it might work with environment valuable change. It's not designed for this board and may cause unexpected issues.
Original Partition table:
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x0000000c0000 : "Config"
0x0000000c0000-0x000000100000 : "ConfigData"
0x000000100000-0x000000180000 : "Factory"
0x000000180000-0x000007ae0000 : "firmware"
0x000000180000-0x000000500000 : "kernel"
0x000000500000-0x000007ae0000 : "rootfs"
0x000001540000-0x000007ae0000 : "rootfs_data"
0x000007fe0000-0x00000f940000 : "firmware_backup"
0x00000f440000-0x00000fe40000 : "ClifeData"
(Get that from dmesg, I don't know why last two partition mix together)
Immortalwrt Partition table:
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x0000000c0000 : "Config"
0x0000000c0000-0x000000100000 : "ConfigData"
0x000000100000-0x000000180000 : "Factory"
0x000000180000-0x000000580000 : "kernel"
0x000000580000-0x00000fe40000 : "ubi"
(cherry picked from commit e44074d272)
Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
1. Power down the router and hold in the Reset button.
2. While holding in the button power up the router again.
3. Hold the button in for 10 seconds and then release.
4. Use your browser to go to 192.168.1.1
5. If you see a GUI that is for flashing firmware then you have the V2 model.
If there is no GUI and the router continues to boot up normally
you have the V1 model.
6. Now use the V2 sysugrade file.
Note: Recovery GUI it can be used to recover from an incorrect firmware flash.
Based on patches adding support for this device by Yannick Chabanois (openmptcprouter)
and Dairyman (ofmodemsandmen)
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18514
(cherry picked from commit c908fc7d95)
Link: https://github.com/openwrt/openwrt/pull/19216
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport some additional upstream patches to resolves some issues when using
dt overlays on gw72xx-0x and gw73xx-0x:
- 6.13-arm64-dts-imx8mm-venice-gw73xx-remove-compatible-in-overlay-files.patch
- 6.12-arm64-dts-imx8mm-venice-gw72xx-remove-compatible-in-overlay-files.patch
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19218
Signed-off-by: Robert Marko <robimarko@gmail.com>
The current code uses functions and features only found in newer
versions of Python, so rework to allow use on systems only supporting
older Python. Tested on Python 3.8 (released Oct 2019), but should
work on 3.7 also.
Suggested-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
(cherry picked from commit 0c7d564b1d)
Some devices use third-party non original uboot and mibib, and OpenWrt expand layout cannot flash and boot normally on such partitions
Signed-off-by: jinkela air <air_jinkela@163.com>
(cherry picked from commit 753e8267c6)
It's no longer able to decide memory type by USB port, so let's make
the name bit clear.
Please note that the CH version produced in 2025 does not have USB
port but it still uses DDR3 memory.
As far as we know, CH/XW = DDR3, WS = DDR4.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 9e88ba8367)
This commit changes LAN1 to be WAN and LAN2 to be LAN, like all other
dual port Extreme Networks devices.
This partially reverts commit 84a489b7cf
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
(cherry picked from commit 710ec82367)
Fixes LAN LED "1" to show activity of LAN1 and LAN LED "2" to show
activity of LAN2, not vice versa.
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
(cherry picked from commit f02e614f50)
hostapd_neighbor_set_own_report is normally called from interface setup only.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9850052190)
Ensure that hapd->own_addr is set properly, since hostapd_setup_bss
only handles it for secondary BSS interfaces
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3ebf110711)
The WR3000E has the same board layout as the WR3000S. Differences:
- Different flash chip
- LEDs with red/blue colour intead of white
Hardware:
- MediaTek MT7981 WiSoC
- 256MB DDR3 RAM
- 128MB SPI-NAND (F50L1G41LB)
- MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18609
(cherry picked from commit 300335f1ff)
Link: https://github.com/openwrt/openwrt/pull/19063
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Following the initial support of the Cudy WR3000H with PHY C22 for the 2.5G WAN
interface, several improvements fixing issues with RealTek RTL8221B PHYs have
been merged.
Therefore we can now bring the DT in line with other equipment and declare the
2.5G WAN PHY as C45.
Fixes: 9d66b8b ("mediatek: filogic: Add support for cudy wr3000h")
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17739
[reword commit description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit dcc5587374)
Link: https://github.com/openwrt/openwrt/pull/19124
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The manufacturer Cudy usually releases signed openwrt firmware, to
facilitate the migration from the proprietary version to the official
versions of openwrt. In contact with the manufacturer tells me that only
releases the firmware of the WR3000H if and only if
there is an official version. With this proposal I pretend to have an
initial operative version so that they do their part, and facilitate to
the users the possibility of using openwrt. In the present state, it is
only possible to use this firmware by uploading and installing it with
UART connection.
AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H)
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY (C22)
2 Radios MT7976CN
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to
enter the U-Boot shell (The recovery.bin image load process must fail).
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000h.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000h.bin; bootm 0x46000000
5. IMPORTANT: Make backup from original firmware. System -> Backup
/Flash Firmware -> Save mtdblock contents. All mtdblock one by one,
keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi).
6. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Warning for BL2 and U-BOOT developers
-------------------------------------
The nand partition layout from vendor is slightly diferent from "standard".
The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31.
The UBI partition start at 0x5c0000 be carefull.
DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition
Layout is start-end (not start size)
- 0x000000000000-0x000007800000 : "nmbm0"
- 0x000000000000-0x000000100000 : "bl2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "factory"
- 0x000000380000-0x0000003c0000 : "bdinfo"
- 0x0000003c0000-0x0000005c0000 : "fip"
- 0x0000005c0000-0x0000045c0000 : "ubi"
ALLWAYS for U-BOOT operations check this
setenv mtdids nmbm0=nmbm0
setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi)
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17458
(cherry picked from commit 9d66b8b312)
Link: https://github.com/openwrt/openwrt/pull/19124
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
drop upstream patches
$ git log --no-merges --oneline v2.7.6..v2.8
48ceda8 Version 2.8
b3d0c93 Regression in commit abe92e8010ab affecting MariaDB tests
29fced6 Count traditional diff pattern lines correctly
b5d2124 patch: fix --no-backup-if-mismatch regression
86ac7e2 Fix dodgy assert with side-effects in insert_cached_dirfd
7d87652 Declare an expected test failure on Haiku.
86baf97 build: update gnulib submodule to latest
1ba2c1b Fix two test failures on Haiku.
1da6bf8 Check for newlines only when creating a file name
30ee610 Gnulib renamed some modules
6dbc381 maint: update bootstrap from gnulib
05ac924 build: update gnulib submodule to latest
95e0092 maint: make update-copyright
5bac274 Set --no-backup-if-mismatch when in --posix mode
910fecf Add missing feature tests to the test suite
be8b3c6 Disable release-prep
c61485b Fix "make release" to handle alpha releases
499916f Add announce-gen module for "make release"
adb1ebc Pacify gcc -fsanitize=address
6bdae94 Fix memory leak when malformed unidiff patch
72a146c Port to clang address sanitizer
e2e6820 Refactor argc+argv processing
606c091 Omit needless get_some_switches code
ee3cc40 Revert "Remove obsolete require_gnu_diff function"
8cae4fc Remove obsolete require_gnu_diff function
164b529 savebuf can return a null pointer
91c1e4f Spelling fixes
a03e1ba Port other reject-format test to non-GNU diff
9ba5eb0 Don’t be fooled by NUL bytes in diff directives
79dd5e7 Don’t be fooled by "\000" in file name
8492a6a Port to quasi-GNU diff
f6f2c6f In previous patch, make w_q static
0525681 Pacify -Wunterminated-string-initialization
301411d Spelling fixes
4615206 Remove double semicolon
923e0ef Prefer angle bracket headers
5d17ca0 Update more old copyright notices
5f4edd3 Simplify memory allocation of files to delete
802511c Report patch read errors more immediately
a93b50d Port fflush usage to OpenBSD 7.5
55e224b Update old copyright notices
33a7fd8 Fix gl_gcc_warnings typo in ‘configure’
2313b37 build: update gnulib submodule to latest
37fec39 Remove some dependencies no longer needed
cc87173 Update NEWS as per recent changes
7887622 Update POSIX citations
18f4dd6 Use “Gruenbacher” in international contexts
638675c Adjust libs to match recent Gnulib
53400a1 Pacify clang -Wbitwise-conditional-parentheses
e8e1bcb Remove “support” for nested critical sections
b963510 Simplify critical section code in util fns
85949fb Shrink critical sections
448ff9b Defer signals by hand with sigatomic_t
b95a603 output_file_later avoid a malloc+free pair
2663228 Defend against closed stdin/stdout/stderr
fc77964 Stop using Gnulib ‘execute’ module
470699c Move defer_signals up
f696e4e Make sigs, NUM_SIGS local
4d3a4ab Rename block_signals
b3bb925 Trade a bit of space for time in parse_c_string
070d859 Allocate first patchbuf statically
f46a90f Use bigger buffer size by default
2e64cfd Preinitialize fatal_act.sa_hander
45de0d9 Prefer EXIT_SUCCESS etc. to literal integers
82c4940 Fix some signal handling races
eceea61 Fix --set-utc TZ setting
9c55d3f Improve logic for when rename removes source
61c72f0 Fix signal race when renaming file
705c9bc Simplify traverse_another_path via last_component
77f21a6 Stop using Gnulib dirname module
fe8ffd9 Fix implausible overflow when reading symlinks
5e84bda Access checks should use effective, not real
8d4ca49 Don’t assume AT_FDCWD != -1
fe5d4a0 Copy input to output attributes via fd if possible
ca4c431 Simplify timestamp epoch checking
0ad4347 Check for ftello failures
c49a16d Remove format_linenum
22efdee Fix "with multiple words" line number
5a70a1b Drop Plan B
c0d465f Prefer ximemdup0 to xmemdup0
b91aab2 Refactor ifetch API
55c8a5c Do not attempt huge I/Os
e0e121e Use outfd when setting file attributes
241e57e Don’t assume Linux-like S_IFREG
0f8c628 Use STDOUT_FILENO etc
f2c3676 Fix unlikely glitch with ed diffs
cec6407 Use fds to copy attrs in create_backup_copy
6b7b01b Be more careful about (time_t) -1
0433553 X == -1 → X < 0
0a66dee Let set_file_attributes use fds not names
36ff2c9 Port to narrow unsigned uid_t
3951496 Check for output errors more systematically
6429630 Report input error right away
03cb187 Simplify EOF testing
cc7cde7 Prefer other types to ‘int’
4c6650b Detect unlikely integer overflow in size calcs
abe92e8 Prefer idx_t, ptrdiff_t to lin
30449e2 Fix compatibility issue with blanks in patches
9228a8c pch_swap return type cleanup
c1c438d Fix unlikely int overflow in hunk counts
5d3f41f Use char for char in plan_a
fb056f2 Cache cwd_is_root dev, ino
84b5f34 Avoid ‘unsigned’ in safe.c
d2e113e Simplify get_sha1
f73718b Avoid casts in patch.c
79eef3e Prefer idx_t in util.c
11588d0 Prefer idx_t in pch.c
e16037d Prefer idx_t in patch.c
388926f Prefer idx_t in list.h
3582fdb Prefer idx_t in inp.c
4a47c00 build: update gnulib submodule to latest
4f8c4b8 Don’t limit strip counts etc. to INT_MAX
0a810b6 Fix unlikely integer overflows in patch.c
bac3b6d Fix unlikely integer overflows in pch.c
8fb784b Fix unlikely integer overflows in inp.c
e10f3ca Promote minmax.h to common.h
57e2165 Avoid some memory allocation by not using ‘const’
eb18b39 Remove unnecessary char * casts in inp.c
d60cb72 Pacify gcc -Wunused-parameter when !USE_XATTR
05ef886 Pacify gcc -Wunused-parameter when !USE_XATTR
1f8d192 maint: stop using alloca
ba92722 Don’t assume O_RDONLY == 0
0f98e03 Avoid syscall when nested signal block
1235ccc Add signal comment
43ee674 build: update gnulib submodule to latest
e381947 Update NEWS, README-prereq
2c2a83b Omit _Noreturn when easy
a13c2ea Replace __attribute__ with attribute.h
6eb2d13 Switch from ctype.h to c-ctype.h
d1a6847 Simplify warning configuration
d6631b3 Prefer ATTRIBUTE_* to _GL_ATTRIBUTE_*
bc6899d Pacify gcc -Wno-unused-parameter
da25985 Improve ‘git diff’ output if desired
248ef13 Prefer strerror to perror
6cb321a A bit more long-string fixing
47bc09d Prefer nullptr to NULL
7608746 More fixing of printing of very long strings
323da0d Don’t assume string sizes fit in int when printing
53d1014 Avoid fprintf INT_MAX overflow when merging
59681c8 Avoid sprintf INT_MAX overflow
4278b91 Reject output file names containing '\n'
34b45bc Update man page a bit.
d18c05d Update copyright notices
af828e5 Fix some races involving signals
b3a6c95 Don’t attempt to remove files we didn’t create
9abc949 Omit goto in try_safe_open
90e62d5 Pacify clang re obsolete O_CREAT test
2b87c1e Allow nested block/unblock of signals
7aa1c3b Adjust to new Gnulib bootstrap post imports
99c0c0b maint: remove generated file lib/Makefile.am
1c087d6 Rely on Gnulib inttypes module
7214f8d Update main locals more consistently
6785b2c Use struct outfile * in function args
72d7ed0 Refactor temp names into struct
abf6fb1 Simplify by using Gnulib sigaction
d3816ac Avoid unnecessary freeing in output_files
346d3ac Clean up cleanup
ff2317b Port better to GNU/Hurd
c2d9792 Don’t say empty backups are unreadable
8c27a03 Spelling fixes
d46d729 Change manywarnings usage to be more like coreutils
924698b Pacify clang, which dislikes n + "y"
8939519 Pacify -Wstrict-overflow in pch.c
531cc2b Pacify -Wsuggest-attribute=format in util.c
ff13fea Port to non-VLA C compilers
3d5c0d1 Rename vars to pacify gcc -Wshadow
56788ce Stop including stdbool.h
c10da77 Recommend 64-bit time_t on 32-bit platforms
1e21767 Remove pch_sha1
39005cf Move skip_spaces
755712d Remove pch_timestamp function
04f0eeb Prefer extern inline to static inline for list.h
f06c123 maint: pacify gcc 14 -Wcast-align
aab6e7b maint: pacify -Wanalyzer-null-argument
d1d32c9 maint: work around GCC bug 109839
7575694 maint: pacify gcc -Wmissing-variable-declarations
8f78b09 maint: pacify gcc -Winline
bb841fd maint: port _FORTIFY_SOURCE to Ubuntu
4887683 maint: assume STDC_HEADERS
5b8ecde maint: spruce up our .m4 files a bit
009a424 maint: omit obsolete macro calls
299167f maint: simplify .gitignore
3ec44a4 build: update gnulib submodule to latest
68cb529 build: update gnulib submodule to latest
f144b35 build: Enable the 'subdir-objects' Automake option.
faafc79 build: update gnulib submodule to latest
c835ecc Pass the correct stat to backup files
24f81be maint: modernize README-{hacking,prereq}
7623b2d Fix test for presence of BASH_LINENO[0]
0993940 gnulib: update to latest
78ed9de Add missing-section tests to context-format test case
76e7758 Fix failed assertion 'outstate->after_newline'
15b158d Avoid invalid memory access in context format diffs
dce4683 Don't follow symlinks unless --follow-symlinks is given
61d7788 Don't crash when RLIMIT_NOFILE is set to RLIM_INFINITY
b7b028a Abort when cleaning up fails
a5b442c Skip "ed" test when the ed utility is not installed
2b584ae Improve support for memory leak detection
9c98635 Fix swapping fake lines in pch_swap
ff81775 Make the (debug & 2) output more useful
369dccc Don't leak temporary file on failed multi-file ed-style patch
1959988 Don't leak temporary file on failed ed-style patch
f322a7e Request 'alloca' module from gnulib.
458ac51 Fix 'ed-style' test failure.
1e9104c Fix check of return value of fwrite().
ae81be0 maint: avoid warnings from GCC8
2a32bf0 Minor cleanups in do_ed_script
ff1d3a6 Use gnulib execute module
3fcd042 Invoke ed directly instead of using the shell
123eaff Fix arbitrary command execution in ed-style patches (CVE-2018-1000156)
b5a91a0 Allow input files to be missing for ed-style patches
f290f48 Fix segfault with mangled rename patch
074e239 Test suite: fix Korn shell incompatibility
f6bc5b1 Test suite compatibility fixes
3bbebbb Avoid set_file_attributes sign conversion warnings
Signed-off-by: Russell Senior <russell@personaltelco.net>
Link: https://github.com/openwrt/openwrt/pull/18479
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f45df2167b)
TF-A LTS releases have an lts- prefix in their version tag. Introduce a
PKG_LTS variable to support these.
As the non-LTS tarbals do not contain the version prefix in the
directory, we need different PKG_BUILD_DIR for each variant:
➜ tar --list --file dl/trusted-firmware-a-v2.12.tar.gz | head -n1
trusted-firmware-a-2.12/
➜ tar --list --file dl/trusted-firmware-a-lts-v2.12.1.tar.gz | head -n1
trusted-firmware-a-lts-v2.12.1/
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
cherry picked from commit 06c4e8a262
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19076
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
[1] https://github.com/openwrt/openwrt/issues/17351
[2] https://lore.kernel.org/all/0adde34f936a2dafca40b06b408d82afe0852327.camel@mediatek.com/
Tested-by: Darren Tucker
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://github.com/openwrt/openwrt/issues/17351
Link: https://github.com/openwrt/openwrt/pull/18585
(cherry picked from commit b7fa9d92ae)
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Link: https://github.com/openwrt/openwrt/pull/19150
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
61ae5732adea iprule: amend ipproto netlink nla_put_u32 to nla_put_u8
d610d68c71b8 device: add support for configuring vrf
a1b6386a20a6 device: fix bonding primary port selection
e8bbf246ce2e system-linux: fix sysfs name for all_ports_active flag
723c699e84f4 Restore disable_ipv6 sysctl after removing a device from bridge or bond
d476e18e8d43 iprule: resolve ipproto by name
7901e66c5f27 netifd: iprule add sport and dport
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 15c2ca0a83)
Link: https://github.com/openwrt/openwrt/pull/19125
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A previous commit backported the ipq-wifi update to fix support for the
TP-Link Archer C6 v2 by adding the device to the package. However, it
missed adding the required TARGET_ath79 dependency, causing the
ipq-tplink_archer-c6-v2 build to fail.
The dependency was previously added in commit 4990ce613b ("ipq-wifi:
update to 2024-02-17") when several ath79 devices were introduced.
However, since this backport only fixes support for the Archer C6 v2, it
is not feasible to backport all related changes. Therefore, this commit
adds only the missing dependency to resolve the build issue without
pulling in unrelated updates.
Fixes: 0c43acc349 ("ipq-wifi: update to Git HEAD (2025-05-30)")
Signed-off-by: Nick Hainke <vincent@systemli.org>
Link: https://github.com/openwrt/openwrt/pull/19120
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hold a reference to the defer resource as long as it is still needed
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 87bfde67f2)
567207a9bf16 fs: implement fileno() on directory handles
eb1d93235509 fs: support passing directory handle or fd in chdir()
38a2254337f1 build: detect whether toolchain employs default source fortification
6eddfc9dff17 resolv: fix fd leak in send_queries
3d36856b2dc5 uci: fix memory leak on cursor() error
aafde95f1ecf uci: add cursor() flags argument
d8cebc5a6bfd Revert "WIP: lib: support map() over objects"
2599cf80736b zlib: incorporate latest PR changes
830f316a7e49 socker: let sock.peercred() clear error on success
4cbac141406e types: rename u64_to_constant flag to ext_flag
d802fe5da5cd types: add support for resources with embedded data/values
71b4fdc6f60b types: add support for setting resource persistent flag
141f799eba08 uloop: use container_of instead of direct pointer casts
1396f8f2988d uloop: use uc_fn_thisval
9a121fc7440c uloop: drop object_registry
11b804d97086 socket: do not clear last_error in socket.error()
d5b3a9dc1091 socket: add strerror() method
Fixes: https://github.com/jow-/ucode/issues/285
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2a9316fbfb)
The I2C and SPI packages required for each RPi generation is different.
Therefore, in order to avoid confusion let's select them by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 9117ff7b39)
Add kernel package for Broadcom Settop/DSL I2C controller.
This controller is used on RPi devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 59f8312400)
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 84922a1e34)
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 4987239913)
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 82d20a0fbd)
Xcode 16.3 defines TARGET_OS_MAC, it was not defined in prior versions.
zutil.h conditionally defines fdopen as NULL when this macro is defined,
resulting in the following build error:
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/_stdio.h:318:7: e>
318 | FILE *fdopen(int, const char *) __DARWIN_ALIAS_STARTING(__MAC_10_6, __IPHONE_2_0, __DARWIN_ALIAS(fdopen));
| ^
./zutil.h:147:33: note: expanded from macro 'fdopen'
147 | # define fdopen(fd,mode) NULL /* No fdopen() */
In Xcode 16.2 and earlier, TARGET_OS_MAC was not defined so this entire
block was ignored, gcc and gdb used to compile and work fine.
This may have been used for compatibility with older versions of macOS,
but is no longer needed. By pure luck, the build worked fine for a long
time, because it did not properly detect macOS.
Fixed by removing the check for TARGET_OS_MAC.
Note that since Xcode 16.3, an entire set of TARGET_OS macros
are now defined, most of which are set to 0:
TARGET_OS_LINUX 0
TARGET_OS_MAC 1
TARGET_OS_OSX 1
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18467
(cherry picked from commit d3bb23946e)
Link: https://github.com/openwrt/openwrt/pull/19096
Signed-off-by: Robert Marko <robimarko@gmail.com>
Xcode 16.3 defines TARGET_OS_MAC, it was not defined in prior versions.
zutil.h conditionally defines fdopen as NULL when this macro is defined,
resulting in the following build error:
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/_stdio.h:318:7: error: expected identifier or '('
318 | FILE *fdopen(int, const char *) __DARWIN_ALIAS_STARTING(__MAC_10_6, __IPHONE_2_0, __DARWIN_ALIAS(fdopen));
| ^
./zutil.h:147:33: note: expanded from macro 'fdopen'
147 | # define fdopen(fd,mode) NULL /* No fdopen() */
In Xcode 16.2 and earlier, TARGET_OS_MAC was not defined so this entire
block was ignored, gcc and gdb used to compile and work fine.
This may have been used for compatibility with older versions of macOS,
but is no longer needed. By pure luck, the build worked fine for a long
time, because it did not properly detect macOS.
Fixed by removing the check for TARGET_OS_MAC.
Note that since Xcode 16.3, an entire set of TARGET_OS macros
are now defined, most of which are set to 0:
TARGET_OS_LINUX 0
TARGET_OS_MAC 1
TARGET_OS_OSX 1
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18467
(cherry picked from commit dfb8115d0c)
Link: https://github.com/openwrt/openwrt/pull/19096
Signed-off-by: Robert Marko <robimarko@gmail.com>
lldpd can send several hardware inventory TLV fields. Extend the init
script to provide these when the existing flag 'lldpmed_no_inventory' is
disabled. Five new methods provide default values for some of them,
taken from /etc/os-release and /etc/board.json.
There is no homogeneous method to determine the hardware serial number,
so it can be provided manually, as can asset ID.
Note: properties >= 32 characters are truncated at send time (by lldpd),
and some (Cisco) equipment displays junk after strings >= 32 characters.
So truncate to 31.
Tested on: 24.10.0 (known compatible with 22 and 23 also)
===
Example
===
The following lldpd config lines:
configure inventory hardware-revision "v0"
configure inventory software-revision "r28427-6df0e3d02a"
configure inventory firmware-revision "OpenWrt 24.10.0"
configure inventory serial-number "ABCDEF-123456"
configure inventory manufacturer "glinet"
configure inventory model "GL.iNet GL-MT6000"
# 32 characters:
configure inventory asset "abcdefghijklmnopqrstuvwxyz 12345"
Produce the following TLV (decoded by Wireshark):
Telecommunications Industry Association TR-41 Committee - Inventory - Hardware Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0000 0110 = TLV Length: 6
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Hardware Revision (0x05)
Hardware Revision: v0
Telecommunications Industry Association TR-41 Committee - Inventory - Firmware Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0011 = TLV Length: 19
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Firmware Revision (0x06)
Firmware Revision: OpenWrt 24.10.0
Telecommunications Industry Association TR-41 Committee - Inventory - Software Revision
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0101 = TLV Length: 21
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Software Revision (0x07)
Software Revision: r28427-6df0e3d02a
Telecommunications Industry Association TR-41 Committee - Inventory - Serial Number
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0100 = TLV Length: 20
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Serial Number (0x08)
Serial Number: ABCDEF-123456
Telecommunications Industry Association TR-41 Committee - Inventory - Manufacturer Name
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0000 1010 = TLV Length: 10
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Manufacturer Name (0x09)
Manufacturer Name: glinet
Telecommunications Industry Association TR-41 Committee - Inventory - Model Name
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0001 0101 = TLV Length: 21
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Model Name (0x0a)
Model Name: GL.iNet GL-MT6000
Telecommunications Industry Association TR-41 Committee - Inventory - Asset ID
1111 111. .... .... = TLV Type: Organization Specific (127)
.... ...0 0010 0011 = TLV Length: 35
Organization Unique Code: 00:12:bb (Telecommunications Industry Association TR-41 Committee)
Media Subtype: Inventory - Asset ID (0x0b)
Asset ID: abcdefghijklmnopqrstuvwxyz 1234
The Cisco DUT displays:
Hardware Revision: v0
Firmware Revision: OpenWrt 24.10.0
Software Revision: r28427-6df0e3d02a
Serial Number: ABCDEF-123456
Manufacturer Name: glinet
Model Name: GL.iNet GL-MT6000
Asset ID: abcdefghijklmnopqrstuvwxyz 1234
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18354
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 412c850f07)
Link: https://github.com/openwrt/openwrt/pull/18469
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since the early beginning of the Realtek DSA driver there is an uncovered
locking issue between the standard (parent) mdio bus and the DSA (child)
mdio bus. This comes from the fact that the DSA bus simply links to the
parent read and write functions and calls them directly. This leads to
the following lock issue.
- Child bus calls phy_read/write functions and uses its internal lock
- Parent bus calls phy_read/write functions and uses its internal lock
It becomes clear that critical section can be accessed twice without
knowing that a operation from the other bus is currently active. This
can lead to critical malfunctions because the mdio driver needs a lot of
internal magic to get page selection done right. Effects are:
- The original page is lost after a phy_write/read_paged() call
- dmesg like "Realtek RTL8218B (external) rtl838x slave mii-0:00:
Expected external RTL8218B, found PHY-ID 6b23"
Other DSA drivers simply use the read/write functions from the parent bus
and thus avoid locking issues. Do it the same way.
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18824
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 461fc06f9d)
Link: https://github.com/openwrt/openwrt/pull/18755
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cleanup the code of the RTL83xx packet receive interrupt handler. Not
only for better readability but to avoid inconsistencies and stalls on
the RTL839x targets.
The current implementation seems to come from the GPL source code.
Calling the existing cleanup() function inside the interrupt context
without any locks conflicts with SMP & NAPI polling and makes things
worse instead of giving any benefit. Simply ignore RX buffer overruns
and let the device handle packet dropping itself.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18855
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8dde1e4638)
Link: https://github.com/openwrt/openwrt/pull/18755
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The RTL8214FC currently uses generic PHY functions. That makes it look like a copper
device. Switching to/from fibre works fortunately but the autonegotiation handling
still works on MII_LPA (PHY register 5) as if a copper link is used. Fix that by
- advertising a superset of TP/FIBRE features
- using clause 37 functions when on fibre
Additionally enhance the code of the driver to assist further development.
- log the speed of the inserted module to detect wrongly inserted 10gbase-r modules
- order phy driver functions alphabetically (keep match/name on top)
- remove genphy_loopback as the kernel uses it if not provided
Remark! The driver internally uses PORT_MII for the TP port. Align with that and
report MII to ethtool instead of TP. Other drivers do the same and it can be
changed in the future if needed.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18724
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4cfd1c4501)
Link: https://github.com/openwrt/openwrt/pull/18755
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Arcadyan WE410443 is a WiFi AC access point distributed by various ISPs
under various names, including KPN SuperWifi and BT Whole Home Wi-Fi. It
features one ethernet port, dual MT7615N radios and four internal antennas.
Hardware:
- SoC: Mediatek MT7621AT
- Flash: 32 MB
- RAM: 128 MB
- Ethernet: 1x 10/100/1000 Mbps, built into the SoC
- WLAN: 2x MediaTek MT7615N
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 1x Green, 1x Blue, 1x Red, all unmarked
- Power: 12 VDC, 1.5A barrel plug
Installation:
The bootloader is locked with a password, so the image needs to be written
directly to the SPI flash chip. To do this, you need to open up the case,
remove the heatsink and connect the flash chip to a Raspberry Pi. Use the
following connections:
Flash chip --> Raspberry Pi
VCC --> 3v3
RESET --> 3v3
/CS --> GPIO 8
DO --> GPIO 9
CLK --> GPIO 11
DI --> GPIO 10
GND --> Ground
You can solder wires to the flash chip, or use a SOIC16 clip. More details on
the Raspberry Pi and SPI chip pinouts are available on the wiki [1]
When you have the Raspberry Pi connected to the flash chip, boot your Pi and
follow the instructions:
1) Make sure your Pi has SPI enabled with sudo raspi-config
2) Install necessary tools: sudo apt install xxd libubootenv-tool mtd-utils
3) Upload overlay and execute:
sudo dtc -@ -I dts -O dtb -o
/boot/overlays/we410443.dtbo we410443-overlay.dts
4) Enable in /boot/firmware/config.txt by adding a new line containing
dtoverlay=we410443
5) Reboot your Pi and verify the mtd partitions with
cat /proc/mtd, you should see:
dev: size erasesize name
mtd0: 02000000 00001000 "all"
mtd1: 00030000 00001000 "u-boot"
mtd2: 00010000 00001000 "u-boot-env"
mtd3: 00010000 00001000 "factory"
mtd4: 01f60000 00001000 "firmware"
mtd5: 00010000 00001000 "glbcfg"
mtd6: 00010000 00001000 "config"
mtd7: 00010000 00001000 "glbcfg2"
mtd8: 00010000 00001000 "config2"
6) Optionally (but recommended), make a backup:
sudo dd if=/dev/mtd0 of=backup.bin
It can be restored with: sudo flashcp backup.bin /dev/mtd0
7) Set the variables for the bootloader:
echo '/dev/mtd2 0x0 0x1000 0x1000' > fw_env.config
sudo fw_setenv -c fw_env.config bootpartition 0
8) Finally, flash the image:
sudo flashcp openwrt-ramips-mt7621-arcadyan_we410443-
squashfs-sysupgrade.bin /dev/mtd4
MAC addresses
The label address is stored in ASCII in the config partition
Use --> Address
Device --> label
Ethernet --> label
WLAN 2g --> + 1
WLAN 5g --> + 2
References:
[1] https://openwrt.org/toh/arcadyan/astoria/we410443
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/17981
(cherry picked from commit b6a07dd091)
Link: https://github.com/openwrt/openwrt/pull/19068
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some modems and SIM cards take a bit longer to initialize after UIM has been
powered off. Waiting too little time can cause the qmi protocol to end up
in a loop repeatedly power-cycling the SIM card.
Avoid that by
a) increasing the time we unconditionally sleep after --uim-power-on
b) increasing the time we allow uqmi to wait for response for --uim-get-sim-state
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18772
(cherry picked from commit d63663601d)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Group 'local' declarations and 'json_get_vars', sort alphabetically within groups, and split off more generic parameters.
- delegate and sourcefilter were not declared as local variables
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
(cherry picked from commit bf768867dc)
Signed-off-by: Felix Baumann <felix.bau@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 7cace002ba added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
rockchip target.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18921
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable activity on the WiFi LEDs of the Teltonika RUTX50
like other boards in the ipq40xx target.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 54463f1e2e)
The Teltonika RUTX50 mac-addresses on its wired interfaces are currently
random on every boot.
Setting the mac-addresses from device-tree using nvmem does not work, as
the vendor bootloader mangles the mtd partitions, removing the
nvmem-cells property.
To remedy the random mac-addresse, set the correct ones in preinit.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 08c93512fe)
Turn on the 5G modem of the RUTX50 on by default.
This allows to make the modem detectable on a fresh
installation OOTB without further intervention.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ac1ad1a7ad)
Backport a small fix for brcm legacy dsa tags that has been accepted for
linux v6.16.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 84eefb493b)
Fixes SPI and HSSPI coexistance on bmips bcm6362 and bcm63268.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit ba1017bf74)
Update b43-tools to the latest upstream version to fix a
compilation error with C23:
util.h:25:15: error: 'bool' cannot be defined via 'typedef'
25 | typedef _Bool bool;
| ^~~~
Changelog:
c6fc53f replace custom bool typedef with <stdbool.h>
dadf30c fix format warning in compilation
2fe10ea b43-fwdump: Fix forwarding of arguments to disassembler
Link: https://github.com/openwrt/openwrt/pull/18708
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit f8da45e25d)
Backport upstream commit dropping external definition of mbrtowc. The
said definition conflicts with one provided by GCC 15. Issue found on
24.10 SDK.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Currently, we are filtering out images if DEFAULT:=n or BROKEN:=y are set,
so if you are building from scratch and want to build custom images that
are stripped down to fit, you must edit the image recipe or its just
filtered out.
So, to allow this behaviour when building from scratch as we can assume
that person doing that knows what they are attempting to do lets just limit
the filtering to ImageBuilder.
Fixes: f060615a78 ("image: respect DEFAULT and BROKEN when Default profile is selected")
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RPi upstream repo switched to the upstream SDHOST driver some time ago, so
it's time to do the same in our configs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit cd79b6ede9)
Import pending PXA I2C recovery fixes so that if I2C recovery is enabled in
the DTS it does not completely break I2C as it currently does since kernel
6.6.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit dfacae3049)
Backport upstream pinctrl fixes, these are required for the follow-up I2C
PXA recovery fixes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 831994e258)
Commit d7e82c78d7 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7 ("generic: backport Realtek PHY patches from upstream")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
(cherry picked from commit ab87087672)
This fixes the handling of some FS copper SFP modules using the RollBall
protocol and needing some extra treatment.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit bbe58f9830)
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
(cherry picked from commit eec11fbbb6)
Link: https://github.com/openwrt/openwrt/pull/18822
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, when you select the Default profile it does not honor DEFAULT:=n
nor BROKEN:=y in device profiles but rather just tries to build all of them.
This may work when building directly, but when using Image Builder it will
always fail since no kernel or anything else is present for devices that
have DEFAULT:=n or BROKEN:=Y set since those are skipped during build.
So, lets look for DEFAULT being set to "n" or BROKEN being set to "y" and
then remove clear _PROFILE_SET so they dont end up being marked for
installation.
Fixes: #18410
Link: https://github.com/openwrt/openwrt/pull/18814
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit f060615a78)
Fixes the following warning:
[ 180.314652] NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 610dd871aa)
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit eea4689654)
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 61da745817)
The board name that goes into /etc/board.json and is used by sysupgrade
for image verifications gets determined by the below command:
`strings /proc/device-tree/compatible | head -1`
as per package/base-files/files/lib/preinit/02_sysinfo
On more recent firmware version for the Pine64 RockPro64 v2.1 devices the
first entry is 'pine64,rockpro64-v2.1' however the metadata in the
sysupgrade image only specifies 'pine64,rockpro64' as supported and image
verification will fail.
This change makes it so the image metadata will contain both
'pine64,rockpro64' and 'pine64,rockpro64-v2.1' allowing image verification
to pass on both older and more recent firmware versions.
Signed-off-by: Sam Hegarty <hegarty.sam@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit c592afed4d)
Configure the i2c pins as GPIO outputs and use the i2c-gpio driver to
control the Semtech SX9512 touch controller.
This fixes spurious errors in i2c transactions even at 1kHz with the
native i2c driver.
leds green:wan: Setting an LED's brightness failed (-6)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit f828be4d10)
Add the necessary package dependencies as well as device-tree properties
to support the touch-inputs as well as missing LEDs on the Genexis Pulse
EX400 range extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 49a1781d74)
This driver is required for the touch-inputs as well as some LEDs on the
Genexis Pulse EX400.
The driver was also sent upstream. As the EX400 is currently the only
consumer, the driver is added target-specific for ramips.
Once the driver has been accepted upstream and is provided in a kernel
release used by OpenWrt, the package should be moved to the global input
drivers.
Link: https://www.spinics.net/lists/kernel/msg5669349.html
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0842e79338)
The alternative model name does not need to be represented in the DTS.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ff55daf1eb)
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
(cherry picked from commit c3b8108a2b)
Link: https://github.com/openwrt/openwrt/pull/18550
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Link: https://github.com/openwrt/openwrt/pull/18206
(cherry-picked from commit 907cb88e10)
Link: https://github.com/openwrt/openwrt/pull/18557
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Login as root via SSH (IP 192.168.1.1, port 22)
- Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router
- Run sysupgrade:
sysupgrade -n /tmp/sysupgrade.bin
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
(cherry picked from commit 7921e48d43)
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18522
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
(cherry picked from commit 50d9ca6e5a)
(remove factory image generation)
Signed-off-by: David Bauer <mail@david-bauer.net>
GCC15 has switched the C language default from GNU17 to GNU23[1] and this
causes builds to fail with:
In file included from mips-opc.c:29:
mips-opc.c: In function 'decode_mips_operand':
mips-formats.h:86:7: error: expected identifier or '(' before 'static_assert'
86 | static_assert[(1 << (SIZE)) == ARRAY_SIZE (MAP)]; \
| ^~~~~~~~~~~~~
mips-opc.c:214:15: note: in expansion of macro 'MAPPED_REG'
214 | case 'z': MAPPED_REG (0, 0, GP, reg_0_map);
| ^~~~~~~~~~
So, backport upstream fix for this[2] to fix compilation with GCC15.
Patch for 2.40 was manually refreshed as part of the S390 code does not
exist in 2.40 as it was added after it.
[1] https://gcc.gnu.org/gcc-15/porting_to.html#c23
[2] https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=8ebe62f3f0d27806b1bf69f301f5e188b4acd2b4Fixes: #18678
Link: https://github.com/openwrt/openwrt/pull/18681
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d3216173ab)
The factory image generation for the Genexis EX400 image currently fails
if CONFIG_TARGET_ROOTFS_INITRAMFS is disabled.
Create the factory image only if said config option is enabled to avoid
failing builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4e83d5ec26)
In include/host-build.mk, HOST_BUILD_DIR is set by default value:
HOST_BUILD_DIR ?= $(BUILD_DIR_HOST)/$(PKG_NAME)
However the mold package has no PKG_NAME set at all. This means the
HOST_BUILD_DIR is identical to $(BUILD_DIR_HOST).
In the Host/Prepare stage, by default, the $(HOST_BUILD_DIR) will be
deleted at first unconditionally. Since HOST_BUILD_DIR is identical
to $(BUILD_DIR_HOST), the entire build_dir/toolchain-* directory will
be removed and this will cause build failure.
Adding PKG_NAME:=ld.mold can solve this issue.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18567
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b9cb07eced)
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit cb3fc1aef9)
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 7615de6ef0)
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit a3e51a3956)
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
[bump release, improve commit description and package changes]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d127963a46)
Disable ASPM support for this NIC, fixing strange behavior problems, such as
increased latency, strange uneven throughput, etc.
With this option disabled the NIC achieves stable performance.
Upsteam r8169 driver disables ASPM by default for this NIC.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
[bump release, fix commit description, split 2nd tx queue part]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f99b39fd0c)
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit b5680bd113)
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 9bb151d0c6)
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 617961403c)
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 7aeb837bf4)
In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b9c81d1cb)
Update ca-certificates to version 20241223
* Update Mozilla certificate authority bundle to version 2.70.
The following certificate authorities were added (+):
+ Telekom Security TLS ECC Root 2020
+ Telekom Security TLS RSA Root 2023
+ FIRMAPROFESIONAL CA ROOT-A WEB
+ TWCA CYBER Root CA
+ SecureSign Root CA12
+ SecureSign Root CA14
+ SecureSign Root CA15
The following certificate authorities were removed (-):
- Security Communication Root CA (closes: #1063093)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/18468
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit c79572210f)
Fix execution of initramfs image on NEC Aterm devices by increasing
available memory for lzma extraction of lzma-loader.
The size of initramfs image of v24.10.0 exceeds available memory
(LZMA_TEXT_START - LOADADDR) and loader data running at LZMA_TEXT_START
will be overwritten by extracted data. As a result, LZMA extraction will
be broken and stuck (or unexpectedly reset).
Fix that issue by setting higher LZMA_TEXT_START address to increase
available memory for LZMA extraction by lzma-loader.
log (v24.10.0):
boot> tftpd
tftpd start 192.168.0.1
boot> start tftp load openwrt-24.10.0-ath79-generic-ne
end tftp load length = 6569768
start memory load ...
memory load complete
begin : 0x80040000
length : 6567044
startup: 0x80040000
boot> boot
begin : 0x80040000
length : 6567044
startup: 0x80040000
option: 0x0
NEC Aterm series (QCA9558)
Calibrating SGMII
SGMII cal value = 0xe
Configuring SGMII force mode
SGMII_CONFIG : 0x000000a2
MR_AN_CONTROL: 0x00008140
MR_AN_CONTROL: 0x00000140
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... [:<syntax:value>]');retu <--- (stuck)
IPL:SOFT-RESET <--- (reset by WDT)
memory test ... ok
flinstall OK
boot version: 1.0.0
...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18476
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 10a674d277)
r8127 is an out of tree driver provided by Realtek for RTL8127 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 851ea69d8e)
For WIFI7 devices (such as mt7925e), the dev width is currently
always "20 MHz (no HT)" in monitor mode.
Add EHT and HE160 support to iw_htmode to fix this issue.
Additionally, the following changes are made:
1. Set iw_htmode to 160MHz for VHT160. The reason for the current
VHT160 setting is unclear and seems to have been in place for
over a decade (ibss_htmode [1]). If anyone knows its impact,
please inform me so I can restore it.
2. Modify MHZ to MHz. The original matching table in the current
iw tool uses MHz. Although the match is case-insensitive,
correcting this won't hurt.
[1]: https://github.com/openwrt/openwrt/commit/768d09be8781228d3553142c0f1e1231c6aacc7c
Signed-off-by: Ming Kuang <ming@imkuang.com>
Link: https://github.com/openwrt/openwrt/pull/18319
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 86eb1c0b5a)
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
(cherry picked from commit 99ea96c297)
Link: https://github.com/openwrt/openwrt/pull/18434
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
(cherry picked from commit d8002cb627)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18438
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD -> bba53a117a4a5c29da892962332ff1605990e17a)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 4618d09587)
Do not assume that the various tools like llc can be found under the
same path as clang; instead, look them up through BPF_PATH (while still
preferring ones found next to clang).
This fixes build in common setups with ccache, where clang resolves to a
path like /usr/lib/ccache/bin/clang, but no other tools can be found at
that location.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18422
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 89f1d56a7e)
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5d1dedd9f7)
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 65b8a978de)
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fa50e53aa9)
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
(This was a real problem I encountered with a nanopi R6S device and
an external rtl8152 usb3 network controller - the USB controller would
claim the eth1 name, causing much confusion).
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
(cherry picked from commit effcb6e4c3)
Link: https://github.com/openwrt/openwrt/pull/18347
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.
Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.
Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.
Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 4039388149)
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
(cherry picked from commit 0e4e527865)
Do not verify the format of TLV. Leave that to lldpd.
These lldpd config entries:
config custom-tlv
list ports 'eth0'
option tlv 'replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55'
config custom-tlv
option tlv 'oui 33,44,44 subtype 232'
list ports 'br-lan'
list ports 'eth0'
config custom-tlv # oui-info truncated
option tlv 'add oui 33,44,33 subtype 66 oui-info 5555555555'
config custom-tlv
option tlv 'add oui 33,44,31 subtype 44'
config custom-tlv # invalid oui
option tlv 'add oui 3322 subtype 79'
config custom-tlv # invalid oui
option tlv 'oui 3312 subtype 74'
Produce the following lldpd.conf content:
configure ports eth0 lldp custom-tlv replace oui 33,44,55 subtype 254 oui-info 55,55,55,55,55
configure ports br-lan,eth0 lldp custom-tlv oui 33,44,44 subtype 232
configure lldp custom-tlv add oui 33,44,33 subtype 66 oui-info 5555555555
configure lldp custom-tlv add oui 33,44,31 subtype 44
configure lldp custom-tlv add oui 3322 subtype 79
configure lldp custom-tlv oui 3312 subtype 74
And lldpd (v1.0.13 on v22) logs the following:
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op replace oui 33:44:55 subtype fe
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:44 subtype e8
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:33 subtype 42
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.info lldpd[10916]: custom TLV op add oui 33:44:31 subtype 2c
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3322'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.warn lldpcli[10915]: invalid OUI value '3312'
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: an error occurred while executing last command
Sat Mar 16 19:11:39 2024 daemon.info lldpcli[10915]: lldpd should resume operations
( The last two TLV are invalid: their oui must be three hex bytes, comma
separated. Only the first hex byte of oui-info 5555555555 is used )
Depends on #14867 and its release version bump
Tested on: 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14872
(cherry picked from commit 8d1fe32c2c)
Link: https://github.com/openwrt/openwrt/pull/18343
Signed-off-by: Robert Marko <robimarko@gmail.com>
Quoting the kconfig description for CONFIG_PCPU_DEV_REFCNT:
network device refcount are using per cpu variables if this option is
set. This can be forced to N to detect underflows (with a performance
drop).
This was introduced from kernel 5.13 and was wrongly set as disabled.
Some target actually enables it but this should be always enabled unless
refcount needs to be debugged (unlikely for production images)
Enable in generic and drop the entry in every other target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18174
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ea6f3e49d6)
Apparently U-Boot will discard whole node if requested pin function is
unknown to the driver. This resulted in inability to interact with
U-Boot on the said board, as U-Boot always assumed the recovery key
pressed and issued recovery procedure. Log snippet:
button_gpio gpio-keys: pinctrl_select_state_full: pinctrl_config_one: err=-38
reset button found
button pushed, resetting environment
Recovery procedure also booted recovery image, which didn't affect much
the 23.05.x release, since the root fs argument was valid, so changes
persisted. But as 24.10.x hit with fitblk, the board will boot only
recovery image (initramfs) because of default bootargs will reset on each
boot and U-Boot provided bootargs took precedence.
Fixes: 42eeb22450 ("uboot-mediatek: fix factory/reset button")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250304164507.60511-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f8a2e1c68b)
Since 24.10.0, eth0, used for the WAN interface, does not work. From dmesg:
...
[ 1.831126] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.846204] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
...
[ 1.933969] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.967668] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.975999] mt7530-mdio mdio-bus:1f eth0 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21)
[ 1.986907] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1.987149] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth0
[ 2.004157] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.017698] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.024849] DSA: tree 0 setup
...
[ 4.249680] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
...
Like #15865, it seems that gmac0 does not rename eth0 to dsa until after the
switch ports are initialized, leading to a name collision (error -17 = EEXIST).
This patch follows #17062 by using openwrt,netdev-name to fix the collision.
Signed-off-by: J. S. Seldenthuis <jseldenthuis@lely.com>
Link: https://github.com/openwrt/openwrt/pull/18082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4fed462454)
In some cases hostpkg python from packages feed is used (hostpkg has higher
priority in PATH) which causes build failure (cryptography module is
missing). So override PATH to not use hostpkg python.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18102
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 8c3a43be27)
Debian Changelogs from 20240531:
local access.
- Mitigations for INTEL-SA-01079 (CVE-2024-23918)
Potential security vulnerabilities in some Intel Xeon processors
using Intel SGX may allow escalation of privilege. Intel disclosed
that some processor models were already fixed by a previous
microcode update.
- Updated mitigations for INTEL-SA-01097 (CVE-2024-24968)
Improper finite state machines (FSMs) in hardware logic in some
Intel Processors may allow an privileged user to potentially enable a
denial of service via local access.
- Mitigations for INTEL-SA-01103 (CVE-2024-23984)
A potential security vulnerability in the Running Average Power Limit
(RAPL) interface for some Intel Processors may allow information
disclosure. Added mitigations for more processor models.
* Updated Microcodes:
sig 0x000806f8, pf_mask 0x87, 2024-06-20, rev 0x2b000603, size 588800
sig 0x000806f7, pf_mask 0x87, 2024-06-20, rev 0x2b000603
sig 0x000806f6, pf_mask 0x87, 2024-06-20, rev 0x2b000603
sig 0x000806f5, pf_mask 0x87, 2024-06-20, rev 0x2b000603
sig 0x000806f4, pf_mask 0x87, 2024-06-20, rev 0x2b000603
sig 0x00090672, pf_mask 0x07, 2024-05-29, rev 0x0037, size 224256
sig 0x00090675, pf_mask 0x07, 2024-05-29, rev 0x0037
sig 0x000b06f2, pf_mask 0x07, 2024-05-29, rev 0x0037
sig 0x000b06f5, pf_mask 0x07, 2024-05-29, rev 0x0037
sig 0x000906a3, pf_mask 0x80, 2024-06-03, rev 0x0435, size 223232
sig 0x000906a4, pf_mask 0x80, 2024-06-03, rev 0x0435
sig 0x000a06a4, pf_mask 0xe6, 2024-08-02, rev 0x0020, size 138240
sig 0x000b06a2, pf_mask 0xe0, 2024-05-29, rev 0x4123, size 220160
sig 0x000b06a3, pf_mask 0xe0, 2024-05-29, rev 0x4123
sig 0x000b06a8, pf_mask 0xe0, 2024-05-29, rev 0x4123
sig 0x000c06f2, pf_mask 0x87, 2024-06-20, rev 0x21000283, size 560128
sig 0x000c06f1, pf_mask 0x87, 2024-06-20, rev 0x21000283
* source: update symlinks to reflect id of the latest release, 20241112
* Update changelog for 3.20240910.1 and 3.20240813.1 with new information:
INTEL-SA-1103 was addressed by 3.20240813.1 for some processor models,
and not by 3.20240910. INTEL-SA-1079 was addressed by 3.20240910.1 for
some processor models.
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 14 Nov 2024 15:37:40 -0300
intel-microcode (3.20241029.1) UNRELEASED; urgency=medium
* New upstream microcode datafile 20241029
- Not relevant for operating system microcode updates
- Only when loaded from firmware, this update fixes the critical,
potentially hardware-damaging errata RPL061: Incorrect Internal
Voltage Request on Raptor Lake (Core 13th/14th gen) Intel
processors.
* Updated Microcodes:
sig 0x000b0671, pf_mask 0x32, 2024-08-29, rev 0x012b, size 211968
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 14 Nov 2024 14:49:03 -0300
intel-microcode (3.20240910.1) unstable; urgency=medium
* New upstream microcode datafile 20240910 (closes: #1081363)
- Mitigations for INTEL-SA-01097 (CVE-2024-24968)
Improper finite state machines (FSMs) in hardware logic in some
Intel Processors may allow an privileged user to potentially enable a
denial of service via local access.
- Fixes for unspecified functional issues on several processor models
- The processor voltage limit issue on Core 13rd/14th gen REQUIRES A
FIRMWARE UPDATE. It is present in this release for sig 0xb0671, but
THE VOLTAGE ISSUE FIX ONLY WORKS WHEN THE MICROCODE UPDATE IS LOADED
THROUGH THE FIT TABLE IN FIRMWARE. Contact your system vendor for a
firmware update that includes the appropriate microcode update for
your processor.
* Updated Microcodes:
sig 0x00090672, pf_mask 0x07, 2024-02-22, rev 0x0036, size 224256
sig 0x00090675, pf_mask 0x07, 2024-02-22, rev 0x0036
sig 0x000b06f2, pf_mask 0x07, 2024-02-22, rev 0x0036
sig 0x000b06f5, pf_mask 0x07, 2024-02-22, rev 0x0036
sig 0x000906a3, pf_mask 0x80, 2024-02-22, rev 0x0434, size 222208
sig 0x000906a4, pf_mask 0x80, 2024-02-22, rev 0x0434
sig 0x000a06a4, pf_mask 0xe6, 2024-06-17, rev 0x001f, size 137216
sig 0x000b0671, pf_mask 0x32, 2024-07-18, rev 0x0129, size 215040
sig 0x000b06a2, pf_mask 0xe0, 2024-02-22, rev 0x4122, size 220160
sig 0x000b06a3, pf_mask 0xe0, 2024-02-22, rev 0x4122
sig 0x000b06a8, pf_mask 0xe0, 2024-02-22, rev 0x4122
sig 0x000b06e0, pf_mask 0x19, 2024-03-25, rev 0x001a, size 138240
* Update changelog for 3.20240813.1 with new information
* Update changelog for 3.20240514.1 with new information
* source: update symlinks to reflect id of the latest release, 20240910
-- Henrique de Moraes Holschuh <hmh@debian.org> Sat, 21 Sep 2024 16:40:07 -0300
intel-microcode (3.20240813.2) unstable; urgency=high
* Merge changes from intel-microcode/3.20240531.1+nmu1, which were left out
from 3.20240813.1 by an oversight, regressing merged-usr. Closes: #1060200
-- Henrique de Moraes Holschuh <hmh@debian.org> Sat, 17 Aug 2024 11:31:32 -0300
intel-microcode (3.20240813.1) unstable; urgency=medium
* New upstream microcode datafile 20240813 (closes: #1078742)
- Mitigations for INTEL-SA-01083 (CVE-2024-24853)
Incorrect behavior order in transition between executive monitor and SMI
transfer monitor (STM) in some Intel Processors may allow a privileged
user to potentially enable escalation of privilege via local access.
- Mitigations for INTEL-SA-01118 (CVE-2024-25939)
Mirrored regions with different values in 3rd Generation Intel Xeon
Scalable Processors may allow a privileged user to potentially enable
denial of service via local access.
- Mitigations for INTEL-SA-01100 (CVE-2024-24980)
Protection mechanism failure in some 3rd, 4th, and 5th Generation Intel
Xeon Processors may allow a privileged user to potentially enable
escalation of privilege via local access.
- Mitigations for INTEL-SA-01038 (CVE-2023-42667)
Improper isolation in the Intel Core Ultra Processor stream cache
mechanism may allow an authenticated user to potentially enable
escalation of privilege via local access. Intel disclosed that some
processor models were already fixed by the previous microcode update.
- Mitigations for INTEL-SA-01046 (CVE-2023-49141)
Improper isolation in some Intel Processors stream cache mechanism may
allow an authenticated user to potentially enable escalation of
privilege via local access. Intel disclosed that some processor models
were already fixed by the previous microcode update.
- Mitigations for INTEL-SA-01079 (CVE-2024-23918)
Potential security vulnerabilities in some Intel Xeon processors
using Intel SGX may allow escalation of privilege. Intel released this
information during the full disclosure for the 20241112 update.
Processor signatures 0x606a6 and 0x606c1.
- Mitigations for INTEL-SA-01103 (CVE-2024-23984)
A potential security vulnerability in the Running Average Power Limit
(RAPL) interface for some Intel Processors may allow information
disclosure. Intel released this information during the full disclosure
for the 20240910 update. Processor signatures 0x5065b, 0x606a6,
0x606c1.
- Fix for unspecified functional issues on several processor models
- Fix for errata TGL068/ADL075/ICL088/... "Processor may hang during a
microcode update". It is not clear which processors were fixed by this
release, or by one of the microcode updates from 2024-05.
- Mitigations for INTEL-SA-01213 (CVE-2024-36293)
Improper access control in the EDECCSSA user leaf function for some
Intel Processors with Intel SGX may allow an authenticated user to
potentially enable denial of service via local access. Intel released
this information during the full disclosure for the 20250211 update.
Processor signature 0x906ec (9th Generation Intel Core processor).
* Updated microcodes:
sig 0x00050657, pf_mask 0xbf, 2024-03-01, rev 0x5003707, size 39936
sig 0x0005065b, pf_mask 0xbf, 2024-04-01, rev 0x7002904, size 30720
sig 0x000606a6, pf_mask 0x87, 2024-04-01, rev 0xd0003e7, size 308224
sig 0x000606c1, pf_mask 0x10, 2024-04-03, rev 0x10002b0, size 300032
sig 0x000706e5, pf_mask 0x80, 2024-02-15, rev 0x00c6, size 114688
sig 0x000806c1, pf_mask 0x80, 2024-02-15, rev 0x00b8, size 112640
sig 0x000806c2, pf_mask 0xc2, 2024-02-15, rev 0x0038, size 99328
sig 0x000806d1, pf_mask 0xc2, 2024-02-15, rev 0x0052, size 104448
sig 0x000806e9, pf_mask 0xc0, 2024-02-01, rev 0x00f6, size 106496
sig 0x000806e9, pf_mask 0x10, 2024-02-01, rev 0x00f6, size 106496
sig 0x000806ea, pf_mask 0xc0, 2024-02-01, rev 0x00f6, size 105472
sig 0x000806eb, pf_mask 0xd0, 2024-02-01, rev 0x00f6, size 106496
sig 0x000806ec, pf_mask 0x94, 2024-02-05, rev 0x00fc, size 106496
sig 0x00090661, pf_mask 0x01, 2024-04-05, rev 0x001a, size 20480
sig 0x000906ea, pf_mask 0x22, 2024-02-01, rev 0x00f8, size 105472
sig 0x000906eb, pf_mask 0x02, 2024-02-01, rev 0x00f6, size 106496
sig 0x000906ec, pf_mask 0x22, 2024-02-01, rev 0x00f8, size 106496
sig 0x000906ed, pf_mask 0x22, 2024-02-05, rev 0x0100, size 106496
sig 0x000a0652, pf_mask 0x20, 2024-02-01, rev 0x00fc, size 97280
sig 0x000a0653, pf_mask 0x22, 2024-02-01, rev 0x00fc, size 98304
sig 0x000a0655, pf_mask 0x22, 2024-02-01, rev 0x00fc, size 97280
sig 0x000a0660, pf_mask 0x80, 2024-02-01, rev 0x00fe, size 97280
sig 0x000a0661, pf_mask 0x80, 2024-02-01, rev 0x00fc, size 97280
sig 0x000a0671, pf_mask 0x02, 2024-03-07, rev 0x0062, size 108544
sig 0x000a06a4, pf_mask 0xe6, 2024-04-15, rev 0x001e, size 137216
* source: update symlinks to reflect id of the latest release, 20240813
* postinst, postrm: switch to dpkg-trigger to run update-initramfs
-- Henrique de Moraes Holschuh <hmh@debian.org> Thu, 15 Aug 2024 14:41:50 -0300
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f4801cffc3)
The spaces in variables have been stripped since commit 551e04f3c9
("base-files: strip space and tab characters from ASCII mac address"),
resulting "Vfac_mac " matches nothing. Fix the issue by removing the
space at end.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18150
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2091c29578)
The M1200 v1 is similar to the TR1200 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7628
- MT7628AN (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:A4
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:A4
- WAN (top connector) is label + 1, e.g. xx:xx:xx:xx:xx:A5
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:A4
- WLAN (5G) is label + 2, e.g. xx:xx:xx:xx:xx:A6
UART:
- is available via the pin holes on the board
- The pinout is printed to the board: P: VCC, G: GND, R: RX, T:TX
- RX and TX require solder bridges to be installed
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 4) and White (GPIO 0)
- There are two buttons: Reset (GPIO 11) and WPS (GPIO 5)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18233
(cherry picked from commit c13a050d5a)
Link: https://github.com/openwrt/openwrt/pull/18252
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.83..HEAD
(HEAD -> 08d4e8f52256bd422d8a1f876411603f627d0a82)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 251f76c1c6)
d8b43985e4d7 ubus: fix token_create policy
7326459bd743 ubus: dump service information on network_get
6c9c8fbd8128 service: add @all as alias for all members, unless defined differently
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 84909c62c8)
The M1300 v2 is similar to the WR1300 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7621
- MT7603E (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:1C
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WAN (top connector) is label +2, e.g. xx:xx:xx:xx:xx:1E
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WLAN (5G) is the same as WAN, e.g. xx:xx:xx:xx:xx:1E
UART:
- is available via the pin holes on the board
- From inner to outer pin: TX, RX, GND, VCC
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 3) and White (GPIO 4)
- There are two buttons: Reset (GPIO 8) and WPS (GPIO 10)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- The migration image is also available here until a image is provided by Cudy: https://github.com/RolandoMagico/openwrt-build/releases/tag/M1300_Build_20240222
- File: openwrt-ramips-mt7621-cudy_m1300-v2-squashfs-flash-signed.bin
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- In the migration image, LAN and WAN are swapped. Computer must be connected to the other port after flashing
- OpenWrt is now accessible via 192.168.1.1
- After flashing an up to date OpenWrt image, LAN and WAN settings are again the same as in the OEM firmware
- So use the other connector again
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the LAN port (lower port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18139
(cherry picked from commit 8a78637670)
Link: https://github.com/openwrt/openwrt/pull/18204
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Genexis Pulse EX400 / Inteno Pulse EX400. A branded
variant for the Finnish ISP DNA has already been added in fea2264d9f
(ramips: mt7621: Add DNA Valokuitu Plus EX400, 2023-07-31). This commit
adds support for the generic variants with Inteno and Genexis branding.
Inteno changed its name to Genexis and both brandings exist.
In terms of electronics, there is no difference between the DNA-branded
version and other brandings. LED markings on the case are different,
though. While the DNA-version has a "software-update" LED, the other
versions have a WPS LED. To reduce user confusion, create a separate
image.
Add the different device-tree with the different LED and rename things
to work the same way for both variants.
Specifications:
- Device: Genexis Pulse EX400 / Inteno Pulse EX400
- SoC: MT7621A
- Flash: 256 MB NAND
- RAM: 256 MB
- Ethernet: Built-in, 2 x 1 GbE
- Wifi: MT7603 2.4 GHz 2x2 MIMO, MT7615 5 GHz 4x4 MU-MIMO
- USB: 1x 2.0
- LEDs (GPIO): green/red status, green WPS
- LEDs (SX9512, unsupported): Broadband, Wi-Fi 2.4G, Wi-Fi 5G
- Buttons (GPIO): Reset
- Buttons (SX9512, unsupported): Wi-Fi 2.4G, Wi-Fi 5G, WPS
MAC addresses:
- LAN: U-Boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access, booting can be halted to U-boot by pressing
any key. TFTP and flash writes are available, but only the first one has
been tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI, or from the U-Boot recovery UI, install the
OpenWrt factory image. Alternatively, ssh to the device and use
sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
(cherry picked from commit 3e7337feea)
Link: https://github.com/openwrt/openwrt/pull/18238
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an industrial 4G router equipped with OpenWrt 14.07 OEM
customized version
WARNING: The original firmware device tree is common to multiple
boards, and the device tree name is H9350. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7620A
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN, 4x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (RUN): GPIO/26 active-low
Ethernet: 1x WAN, 4x LAN
Modem 1: GPIO/66 active-low
RF 1 (Modem 1 Signal): GPIO/67 active-low
Modem 2: GPIO 71 active-low
RF 2 (Modem 2 Signal): GPIO/24 active-low
WLAN: GPIO/72 active-low
WPS: GPIO/12 active-low
- Button:
WPS / RESET: GPIO/34 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/62 mode=toggle timeout=1s
- PCIe: 2x miniPCIe for modem
- SIM Slots: 2x SIM Slots
Issue:
- No factory partition, eeprom is located
at /lib/firmware/mt7620a.eeprom
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put rootfs into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press Ctrl+C to break auto boot.
5. Use `system 6` command and follow the instruction to set device
and tftp server IP address and input the rootfs file name.
U-boot will then load the rootfs and write it into
the flash.
6. Use `system 1` command and follow the instruction to set device
and tftp server IP address and input the firmware file name.
U-boot will then load the firmware once.
7. Login to LuCI and use LuCI upgrade firmware.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8922-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17472
Link: https://github.com/openwrt/openwrt/pull/18221
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6a1bdcf545)
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
opkg update && opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
(cherry picked from commit 96c6608346)
[sync uboot defconfigs with 24.10 branch, change apk to opkg]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18218
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Trying to tcpdump DSA conduits results in errors such as
"unsupported DSA tag: mtk".
Backport two commits adding support for various DSA tags to libpcap.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit fad94e8cda)
Currently, enabling USB, BT or Netfilter support after initial compilation
will not trigger a rebuild, so add the missing PKG_CONFIG_DEPENDS so
that rebuild gets triggered.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit fe37574be6)
Backport FORESEE NAND chip support from upstream Linux. The newly
introduced FORESEE F35SQA001G was found on the Xiaomi AX3000T.
Signed-off-by: Erik Servili <serverror@serverror.com>
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit 302c717aa3)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB DDR3 or DDR4
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Get the SN of the device from web interface or the label on the back of the device.
3. Calculate configuration decryption password:
Command "eval" is necessary here as the encryption implentation treats '$...' as (empty) variables.
decpwd="$(eval echo $(openssl passwd -1 -salt aV6dW8bD "your_device_sn"))"
4. Decrypt the configuration:
openssl aes-256-cbc -d -pbkdf2 -k "$decpwd" -in cfg_export_config_file.conf -out cfg_export_config_file.conf.dec
5. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf.dec
6. Edit 'etc/shadow', update (remove) root password: 'root::19179:0:99999:7:::'
7. Edit 'etc/rc.local', insert telnetd command before 'exit 0':
( sleep 3s; telnetd; ) &
8. Repack the configuration:
tar -zc etc/ | openssl aes-256-cbc -pbkdf2 -k "$decpwd" -out cfg_export_config_file.conf
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
9. Upload new configuration via web interface, now you can connect to
CMCC RAX3000Me via telnet.
(Big thanks to https://github.com/lyq1996 who reverse engineered the encryption method)
Check flash type:
If '/dev/mmcblk0' exists on the device, it's eMMC version.
If '/dev/mtd0' exists on the device, it's NAND version.
eMMC Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Write new FIP:
dd if=immortalwrt-mediatek-filogic-cmcc_rax3000me-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
NAND Flash instructions:
1. Connect to RAX3000Me, and backup everything, especially 'Factory' part.
2. Write new BL2 and FIP:
If your device HAS USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr3-bl31-uboot.fip FIP
If your device DOES NOT have USB port, run:
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_rax3000me-nand-ddr4-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve ImmortalWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 57f31cd5b1)
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/18182
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5013efc4f9)
`ucv_array_set` releases the array's reference to the object being cleared.
If this is the last reference to the object, it will be freed, making our
pointer `val` invalid.
To avoid this, we need to obtain our own reference to the object so we
can safely return `val`.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit 6a10da2934)
Since `wpa_ucode_registry_add` collects its own reference to the values added, the
two functions `hostapd_ucode_bss_get_uval` and `hostapd_ucode_iface_get_uval` would
sometimes return a referenced object (from `uc_resource_new`) and sometimes return
an unreferenced object (from `wpa_ucode_registry_get`). Now, both functions always
return a referenced object.
This change also indirectly fixes `hostapd_ucode_bss_get_uval`, ensuring it now
always returns a referenced object.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 7729f96093)
Remove extra ucv_get calls when passing a referenced value to an object
without using it further.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 22eaf18647)
This fixes a common reference counting bug typically along the lines of:
```
uc_value_push(ucv_get(ucv_string_new(...)));
```
This would leave our new string with a reference count of 2, one from
the construction of the string, the other from `ucv_get`. This would
prevent the strings from being correctly cleaned up when it goes out
of scope.
Signed-off-by: Matthew Cather <mattbob4@gmail.com>
(cherry picked from commit f79968ee0f)
When a feed is referenced with a specific commit (i.e. <git_url>^<sha1>),
a full clone was performed and a branch was created from the sha1
and named with the sha1. Other git clones operations are shallowed.
As Git does not support clone at a specific commit, let's first perform
a shallow clone to latest commit, then fetch the relevant commit and
finally checkout it (no more 'pseudo' branch).
It saves bandwith and significantly speeds up the feed update process.
Signed-off-by: Cedric CHEDALEUX <cedric.chedaleux@orange.com>
Link: https://github.com/openwrt/openwrt/pull/18003
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 32d0a57dc1)
kmod-mmc-mtk does not work well on this board, switch back to deprecated
kmod-sdhci-mt7620 driver for now.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
75a236be122a service: add missing null pointer check
f5341f327539 ubus: add api for generating and validating security tokens
3fab99eab4d5 add udebug support
28d86bd30e97 pex: only respond to update requests when we have network data
8e6f37cc361e pex-msg: ignore no-data responses if version is zero
12e6cf7f63e1 pex: create pex host from update responses
edc8fdae463a ubus: show the local addresses in network status
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit ce68f61cb6)
ethtool since version 6.9 introduced support for getting/setting RSS
input transformation supported in Linux since version 6.8.
The now changed kernel ioctl ABI, however, cannot be detected from
userland, and ethtool since version 6.9 simply assumes that a previously
reserved field is now used to set the input transformation.
Unfortunately the default value RXH_XFRM_NO_CHANGE (0xff) used by ethtool
userland creates an incompatibility with older kernels which cannot be
resolved easily without introducing even more ABI breakage.
Work-around the issue and fix support for --set-rxfh and --set-rxfh-indir
ethtool userland tool commands by making the support for input_xfrm
conditional on compile time, and keep it disabled for Linux 6.6.
Fixes: 8c2dcd1518 ("ethtool: update to 6.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Stijn Segers <foss@volatilesystems.org>
(cherry picked from commit 3a7467ffde)
Version 6.11 - October 8, 2024
* Feature: cmis: print active and inactive firmware versions
* Feature: flash transceiver module firmware (--flash-module-firmware)
* Feature: add T1BRR 10Mb/s mode to link mode tables
* Feature: support for disabling netlink from command line
* Fix: fix lanes parameter format specifier
* Fix: add missing clause 33 PSE manual description
* Fix: qsf: Better handling of Page A2h netlink read failure
* Fix: rss: retrieve ring count using ETHTOOL_GRXRINGS ioctl (-x)
* Misc: man page formatting fix
* changelog here: https://git.kernel.org/pub/scm/network/ethtool/ethtool.git/commit/NEWS?id=c0ea4b70c71334ef038f7a3416b228a50dada406
Tested on gl.inet MT6000, retrieve ring count is now working
Signed-off-by: Andrea Pesaresi <andreapesaresi82@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17607
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9454331b7f)
Specification:
* Mediatek MT7981BA
* 256 MB SPI-NAND
* 512 MB DDR4 RAM
* MT7976CN DBDC AX Wi-Fi
* MediaTek MT7531AE (3x LAN Gigabit ports) + Internal Gbe Phy (1x WAN Gigabit port)
* 4x LED (power, internet, fn, wifi)
* 3x buttons (wps, fn, reset)
* 1x USB 3.0 port
Serial Interface:
* 3 Pins GND, RX, TX
* Settings: 115200, 8N1
Notes:
* The device supports dual boot mode
* Fn led reassigned to wlan 2.4
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3811-squashfs-factory.bin"
to "KN-3811_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17135
(cherry picked from commit d087a79b7b)
Link: https://github.com/openwrt/openwrt/pull/18055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB SPI NAND
- 2 LEDs (green, orange)
- 3 buttons (fn, reset, wps)
- 2 2.5Gbit ethernet ports based on Airoha EN8811H phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 115200, 8N1
Notes:
- The device supports dual boot mode
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-mediatek-filogic-keenetic_kn-3911-squashfs-factory.bin"
to "KN-3911_recovery.bin" and place it in tftp server directory.
3. Connect PC with ethernet port, press the reset button, power up
the device and keep button pressed until status led start blinking.
4. Device will download file from server, write it to flash and reboot.
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16830
(cherry picked from commit 5a4eb56a7b)
Link: https://github.com/openwrt/openwrt/pull/18055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
cmcc_a10-ubootmod stands for custom U-Boot layout in ImmortalWrt 23.05,
add compat version to avoid bricking devices. For 24.10+ users you can
just ignore the compat warning.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 4b000293b2)
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write immortalwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write immortalwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve ImmortalWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 4e9240e733)
Changes between 3.0.15 and 3.0.16 [11 Feb 2025]
CVE-2024-13176[1] - Fixed timing side-channel in ECDSA signature
computation.
There is a timing signal of around 300 nanoseconds when the top word of
the inverted ECDSA nonce value is zero. This can happen with significant
probability only for some of the supported elliptic curves. In
particular the NIST P-521 curve is affected. To be able to measure this
leak, the attacker process must either be located in the same physical
computer or must have a very fast network connection with low latency.
CVE-2024-9143[2] - Fixed possible OOB memory access with invalid
low-level GF(2^m) elliptic curve parameters.
Use of the low-level GF(2^m) elliptic curve APIs with untrusted explicit
values for the field polynomial can lead to out-of-bounds memory reads
or writes. Applications working with "exotic" explicit binary (GF(2^m))
curve parameters, that make it possible to represent invalid field
polynomials with a zero constant term, via the above or similar APIs,
may terminate abruptly as a result of reading or writing outside of
array bounds. Remote code execution cannot easily be ruled out.
1. https://www.openssl.org/news/vulnerabilities.html#CVE-2024-13176
2. https://www.openssl.org/news/vulnerabilities.html#CVE-2024-9143
Build system: x86/64
Build-tested: bcm27xx/bcm2712
Run-tested: bcm27xx/bcm2712
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17947
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b4e6fd7b76)
b43aeb5 wireless-regdb: assert and correct maximum bandwidth within frequency difference
68588bf wireless-regdb: Update regulatory info for Syria (SY) for 2020
0dda57e wireless-regdb: Update regulatory info for Moldova (MD) on 6GHz for 2022
b19ab0b wireless-regdb: Update regulatory info for Azerbaijan (AZ) on 6GHz for 2024
f67f40d wireless-regdb: Update regulatory info for Oman (OM)
bd70876 wireless-regdb: Update regulatory rules for Armenia (AM) on 2.4 and 5 GHz
6c7cbcc wireless-regdb: Permit 320 MHz bandwidth in 6 GHz band in ETSI/CEPT
f9f6b30 wireless-regdb: Update regulatory rules for Austria (AT)
39b47ea wireless-regdb: Update regulatory info for Cayman Islands (KY) for 2024
3dd7ceb wireless-regdb: allow NO-INDOOR flag in db.txt
4d754a1 wireless-regdb: Update regulatory rules for Iran (IR) on both 2.4 and 5Ghz for 2021
8c8308a wireless-regdb: Update frequency range with NO-INDOOR for Oman (OM)
c2f11e2 wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Rudy Andram <rmandrad@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17957
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit da2cc98458)
By switching to the new RTL8231 driver in commit b7af54d5c1 ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 890293c13c)
The JG928A has an RTL8231 on the aux mdio bus. Add it to dts to expose
the GPIO pins used to control and monitor the fan speed. To enable speed
control, add the appropriate kernel driver module to DEVICE_PACKAGES.
Of note, this does not control all fans for the unit. The power supply
fans are not controlled.
Signed-off-by: Evan Jobling <evan@jobling.au>
Link: https://github.com/openwrt/openwrt/pull/17699
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit cbd1acbad3)
The old RTL8231 driver integrated the MDIO bus access with the GPIO
control ops, making this driver not very portable to newer platforms.
It depended on the SoC ID instead of the compatible to determine the
MDIO access register, further complicating portability.
A new MFD driver is now available, which offers proper pin config as
well as optional LED support, which can work on any (bitbanged) MDIO
bus. Now that all devices have been migrated, we can drop the old code.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit b410f2216c)
By switching to the new RTL8231 driver in commit b7af54d5c1 ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 807074309d)
Update the common external GPIO DTSI file for the DGS-1210 devices to
use an MDIO device on the auxilairy MDIO bus, as the original driver was
doing behind the screen.
Switching to the new driver will allow for full pin-control and will no
longer reset pin config set by the bootloader.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 3d6a1a7874)
The DTS file for the DGS-1210-10P is slightly different from the other
DGS-1210 devices, in that it didn't specify a gpio-restart node when it
was added. The gpio-restart has been found to work on the DGS-1210-10P
as well, so switch it over to the common definitions.
This converts the last device from the product family to the common
definition for the (external) GPIOs.
Tested-by: Michel Thill <jmthill@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 7c0d1c1eb1)
The 'indirect-access-id' property on gpio0 is a remnant from the
original GPIO driver. This property has not been relevant on the SoC's
embedded GPIO controller for a long time, so just drop it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 022b7d80bf)
Change devices with RTL8231 GPIO expander definition that can easily be
translated to the new RTL8231 binding and carry over any gpio-hogs. This
will let them use the new RTL8231 MFD driver, without any functional
changes.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit b7af54d5c1)
Zyxel GS1900-8 v2 devices have been produced more recently than v1
devices. As there are v1 boards with RTL8380M rev. C SoCs, it can likely
safely be assumed that all v2 devices will also have a recent SoC
revision, supporting the hardware auxiliary MDIO controller.
Make the GS1900-8 v1 use an emulated auxiliary MDIO bus, for backward
compatibility with devices containing an RTL8380M rev. A.
Since the devicetrees are otherwise identical, GS1900-8 v1 devices with
an RTL8380M rev. B or C will also be able to use the (more efficient) v2
image. This includes any currently functioning device with OpenWrt, so
include the old compatible as a supported device for the GS1900-8 v2.
Link: https://github.com/openwrt/openwrt/issues/9534
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 7322d3266d)
The mdio-gpio driver is required to support early revision of RTL8380M
slicon (rev A) where the auxilairy MDIO controller does not function
correctly. Add this driver to the rtl838x kernel so devices with old
SoCs are also able to function correctly.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit efffcfa436)
In order to be able to define the external GPIO controller on an
emulated MDIO bus, move the controller definition outside of the main
GS1900 include for RTL838x-based devices.
Additionally, a new DTSI is provided defining the RTL8231 on the
emulated MDIO bus.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a6a77896f4)
Some RTL8380M-based devices have been around for a long time and use an
early A revision of the RTL8380M SoC. This revision has an issue with
the auxiliary MDIO controller, causing it to malfunction. This may lead
to device reboots when the controller is used.
Provide a bit-banged MDIO bus, which muxes the auxiliary MDIO pins to
their GPIO function. Although this will result in lower performance,
there should otherwise be no functional differences.
Link: https://github.com/openwrt/openwrt/issues/9534
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit d4bf16a9e1)
As the bootloader is reconfiguring the RTL8231 on these devices anyway,
no pin state can be maintained over warm reboots. This results in for
example the PoE disable pin always being asserted by the bootloader.
Define the GPIO line linked to the RTL8231's reset so the MDIO subsystem
will also reset the expander on boot and ensure the line in the correct
state.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit b2d17dbb68)
Switch the Zyxel GS1900-48 over to the new MDIO-based driver for the
RTL8231 GPIO expander.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 45aafe67f3)
Enable the RTL8231 MFD core driver, as well as the pinctrl/gpio driver
to allow RTL839x devices to use it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit fd5797b7ce)
Enable the driver for the Realtek Otto auxiliary MDIO driver so RTL839x
devices can use it. The related node is added to the base devicetree for
rtl839x-based devices, so they can enabled and use it when required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit cddcc69ddf)
For RTL839x, the driver was producing frequent timeouts on bus accesses.
Increasing the timeout to the one from a recent Realtek SDK resolves
these timeouts. To minimize overhead on different SoCs, each controller
can specify their own timeout.
This also add support for the register format as used on RTL93xx.
Support is added for the RTL930x "ext gpio" controller.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 52ffef6471)
regmap_read_poll_timeout() relies on usleep_range() to time the polling
loop. With the current, rather large, scheduling interval, a short
usleep_range() may take a lot longer than expected, causing performance
issues.
Switch the driver over to using regmap_read_poll_timeout_atomic(), which
uses udelay() to time the polling loop.
For comparision, the 'ethtool -m <dev>' command is about 10 times faster
with the atomic variant.
Using 'perf -r10 ethtool -m lan25':
- Driver using regmap_read_poll_timeout():
2.0117 +- 0.0118 seconds time elapsed ( +- 0.58% )
- Driver using regmap_read_poll_timeout_atomic():
0.1674 +- 0.0250 seconds time elapsed ( +- 14.95% )
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 693c1ea81a)
Apply the equivalent of commit f64541db02 ("realtek: HPE 1920 8G PoE+
180W move fans to hwmon") to the 24-ports variants of the HPE 1920 PoE+
switches, with model numbers JG925A and JG926A.
Copy from the original commit message:
Move to using hwmon and gpio-fan. This is by adding gpio_fan_array to
DTS and kmod-hwmon-gpiofan to DEVICE_PACKAGES.
In combination with the new rtl8231 gpio driver the default fan
behaviour will be maximum fan speed.
Bump compat value to 1.1 due to existing config in /etc/config/system
via gpio_switch. Also notify in device compat that fan is now going to
be at bootloader setting (maximum in this case) by default unless turned
down.
As the init script 03_gpio_switches does not perform any action after
removing these devices from it, the file can be dropped.
Link: https://github.com/openwrt/openwrt/pull/17598
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 0a7c8ed9d9)
Update the base DTS file for the 16 and 24 port HPE 1920 devices
(JG923A, JG924A, JG925A, JG926A), causing the new RTL8231 MFD driver to
be loaded at start-up.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 96850585e5)
The GPIO numbering has changed and is not stable. As a result fan
control via gpio_switch is broken, resulting in errors:
"export_store: invalid GPIO 456"
Move to using hwmon and gpio-fan. This is by adding gpio_fan_array to
DTS and kmod-hwmon-gpiofan to DEVICE_PACKAGES.
In combination with the new rtl8231 gpio driver the default fan
behaviour will be maximum fan speed.
Bump compat value to 1.1 due to existing config in /etc/config/system
via gpio_switch. Also notify in device compat that fan is now going to
be at bootloader setting (maximum in this case) by default unless turned
down.
Signed-off-by: Evan Jobling <evan@jobling.au>
Link: https://github.com/openwrt/openwrt/pull/17605
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit f64541db02)
Update the base DTS file for the 8 port HPE 1920 devices (JG920A,
JG921A, JG922A), causing the new RTL8231 MFD driver to be loaded at
start-up.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit e5d1a501cb)
Update the devicetree files to switch the GS1900 devices over to the new
pinctrl and GPIO driver. Enable the drivers to ensure the nodes can be
used.
This may fix issues caused by bad RMW behaviour on the GPIO data lines,
or glitches due to setting the pin direction before the pin level.
Although the driver supports retaining GPIO state after a warm boot,
some bootloaders appear to apply a default configuration on boot, which
may cause an interrupt in PoE-PSE support.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 5141e2d861)
Add pending patches to add RTL8231 support as a MDIO-bus attached
multi-functional device. This includes subdrivers for the pincontrol and
GPIO features, as well as the LED matrix support.
Leave the drivers disabled until required by a device.
Cherry picked from commit 6ef6014887, but
dropped already picked patch for gpio-regmap request/free, and rebased
configs
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add a disabled node for the auxiliary MDIO bus, used to manage the
RTL8231 expanders. A simple-mfd parent node is added, at the same
(implied) address as the switch@1b000000 node, as the switch drivers
should anyway transistion to MFD subdivices at some point.
Additionally, two pinctrl-single node are added to allow the MDX pins to
be muxed correctly, in case the bootloader leaves these unconfigured.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 92ae8cb16c)
Add a driver that exposes the auxiliary busses, used for the RTL8231
expanders, as a proper MDIO controller. The device must be instantiated
under an MFD device, so the driver should also be compatible with SoC
managed by an external CPU via SPI.
Leave the driver disabled in builds until required.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit ae833c01b3)
Apply "u-boot-dont-touch-spi-nand" to ASUS RT-AX59U, ASUS TUF-AX4200 as
well as ASUS TUF-AX6000 routers to prevent U-Boot from wiping MTD
child nodes from DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 4387de9445)
ASUS makes use of U-Boot's fdt_fixup_mtdparts() function which applies
the partitions defined in U-Boot's mtdparts and mtdids environment
variables to the devicetree passed over to Linux.
The undesired side-effect is that in this way also all additional
properties and child nodes get wiped, preventing NVMEM cells to be
defined for MTD partitions or UBI volumes.
To work-around this issue, add an additional compatible string
'u-boot-dont-touch-spi-nand' which can be used instead of 'spi-nand' in
case the replacement of the MTD partitions by U-Boot should be skipped
alltogether.
In practise this is mostly relevant for SPI-NAND which anyway comes only
with two partitions nowadays: 'Bootloader' and 'UBI_DEV'. Hence this
work-around is applicable for SPI-NAND only. Similar work-arounds for
other MTD devices can be created as well should they actually be needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c48afca32c)
Add kernel command line replacement hack to qualcommax. Now we can
find and replace arguments in the kernel command line by setting
bootargs-find-1, bootargs-replace-1, bootargs-exact-match-1
and bootargs-find-2, bootargs-replace-2, bootargs-exact-match-2
under the chosen node in the device tree.
This hack replaces the first occurence of bootargs-find-X with
bootargs-replace-X. When bootargs-exact-match-X is set to "y",
then the replacement happens only if the kernel command line is
identical to bootargs-find-X.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
(cherry picked from commit 337f6f76ca5361f45e76facd52396936b9fc25c0)
Signed-off-by: Rafal Boni <rafal.boni@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17889
Signed-off-by: Robert Marko <robimarko@gmail.com>
It will require too much effort to make the driver work in kernel 6.6.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit d04b0cbe39)
This reverts commit f628467dfd.
The initial fix was correct. However, a recently introduced bug in
base-files can cause some unexpected byte overwriting in eeprom.
Since it has been fixed, let's accept this patch again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17892
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 43bc5e6e12)
When support for Routerboard 911G was introduced, Routerboad 912UAG
device tree was used as a base, and the common part. This led to use of
40MHz as the reference clock frequency for both [1], while RB911G uses 25MHz
crystal on the board, causing heavy system clock drift.
Split the definition, and set the reference clock frequency for RB911G
back to 25MHz.
[1] a716ac5564 ("ath79: fix reference clock for RouterBoard 912UAG")
Fixes: bcc44b1212 ("ath79: support for MikroTik RouterBOARD 911G-(2,5)HPnD")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17944
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 40fc6bd5cc)
Depending on the config / circumstances, the get_psk call can be called
multiple times from differnt places, which can lead to wrong sta->psk_idx
values. The correct call is the one that is also interested in the vlan_id,
so use the vlan_id pointer as indication of when to set sta->psk_idx.
Also fix off-by-one error for secondary PSKs
Fixes: b2a2c28617 ("hostapd: add support for authenticating with multiple PSKs via ubus helper")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 8118b2dace)
The 00 address_mask needs to be inverted, otherwise the mac address
allocation will modify the last byte instead of the first one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 1ee44825ad)
93458ac dns: fix response to TYPE_PTR query
68af311 fix unicast response port and timeout
a2b4979 service: announce all services in single dns answer
4537734 display announced services in ubus call umdns browse
0b50c29 display more srv attributes in output of ubus browse function
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit d162fd5ed4)
322500403615 service: add default group @ to match all nodes
5f7860306200 ubus: rename unetd_ubus_notify to unetd_ubus_network_notify
d13752814651 enroll: add PEX sub-protocol to support enrolling new nodes into a network
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit c0f06cb6ac)
47b54cf5a4b6 types: introduce `ucv_array_sort_r()` and `ucv_object_sort_r()`
efeb57806552 types, vm: refactor usage of global variables
f9d2faf67de6 vm: reset signals when freeing VM
4e86847d802d lib: utilize `ucv_array_sort_r()` and `ucv_object_sort_r()`
c71444ea301f types: ucv_resource_create(): rename `typename` parameter to `type`
373df7299c79 nl80211: properly support split_wiphy_dump for single phys
9bcd25f54708 lexer: Preserve keyword, regexp flags until processing non-comment tokens
0a7ff4715cb8 main: pretty-print `-p` output by default
4c3d5b469156 struct: Add new buffer API for incremental packing/unpacking
efc4122124cb struct: do not use global variables for caching types
Fixes: https://github.com/jow-/ucode/issues/248
Fixes: https://github.com/jow-/ucode/issues/250
Fixes: https://github.com/efahl/owut/issues/25
Link: https://github.com/openwrt/openwrt/pull/17191
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit af6f1a90bb)
b0b5d93 Merge pull request #234 from IdWV/fs
60e7a88 Merge pull request #232 from sebastianertz/lib-digest
1752779 digest: implement compile time option to exclude less common algorithms
c7268a1 ci: include libmd in MacOS CI builds
fcb6f70 lib: introduce digest library
1323a27 Merge pull request #246 from jow-/fix-upvalue-resolve
ed5ce8f types: resolve upvalue values in arrays and objects
a6e0641 vm: resolve upvalues before pushing them onto the stack
ef1baab ci: drop OpenWrt tests for now
63e18ea fs: eliminate the usage of global variables
b1bd7b5 types: add ucv_resource_create() helper
3408edf Merge pull request #244 from nbd168/nl80211
8af77e7 nl80211: add new attributes for multi-radio support
1423ad7 nl80211: cover extended feature and EHT rate info attributes
ee1d6d8 Merge pull request #237 from sebastianertz/math
4b18a9b Merge pull request #213 from jow-/improve-vector-macros
1f022c0 math: removed global variable for thread safety
e5fe6b1 treewide: refactor vector usage code
20307ee utils: improve vector utilities
aa18952 Merge pull request #241 from jow-/socket-local-fanout-decl
79ccd9c socket: provide local definition of `struct fanout_args`
402280d Merge pull request #239 from jow-/safe-insert-during-obj-iteration
07afe96 Merge pull request #240 from jow-/stricter-number-conversion
736d450 types: fix potential use after free on adding keys during iteration
4134e71 vallist: more thoroughly check for trailing garbage after numeric string
9cf53dd Merge pull request #226 from jow-/lexer-improvements
2b2e732 lexer: make api functions public
855854f lexer: emit comment and template statement block tokens
328a50f lexer: improve token position reporting
fa22732 Merge pull request #225 from jow-/compiler-fix-keyword-property-labels-after-spread
6e88c62 Merge pull request #224 from jow-/lib-fs-readline-leak
94d1211 compiler: properly treat property names after spread expressions
67cd123 fs: fix potential memory leak on i/o errors in .read()
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit ba9cdbeea8)
Replace removed qcom,boot_pages_size prop with qcom,boot-partitions.
Also update to use new emc2305 fan driver.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 32b366e450)
This commit fixes nmbm configuration mismatch error on Xiaomi AX3000t
with Winbond W25N01KVZEIR spi-nand:
'''
[ 0.786783] NMBM configuration mismatch
'''
Root cause:
1. U-Boot W25N01KV spi-nand driver ia compiled with 64B OOB size for the
chip and store this size in the nmbm signature;
2. Linux W25N01KV driver use 96B OOB.
The change doesn't affect AX3000t variants with other spi-nand chips
(ESMT, Foresee) because their Linux drivers use 64B OOB.
Fixes: openwrt#16972
Tested-by: Aleksandr Danilov <sc16me@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3299d19c01)
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17898
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Makes it easier to enable MDNS on wan without having to edit the firewall
configuration for it
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 05138fe898)
It's no longer able to generate images for devices with limited flash
(<= 8 MiB), so just use the full feature wpad.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
It's no longer able to generate images for devices with limited flash
(<= 8 MiB), so just use the full feature wpad.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Unless another toolchain is present (or selected), build the bpf toolchain
whenever a package is selected that needs it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 6605e45676)
This reverts commit 3295f6f1c2.
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
Fixes: #17818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f628467dfd)
Fix broken WAN on Linksys EAX and Asrock G10 by incrementing the WAN
interface MAC address + 1. This caused conflicting entry in the FDB
table and caused the WAN port to malfunction with the DSA conversion.
Fixes: #17157Fixes: #15585Fixes: #16604
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit eba2fbf638)
In general the delay should be added by the PHY instead of the MAC,
and this improves network stability on some boards which seem to
need different delay.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit eb658d5020)
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 69890e16b3)
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c87a767801)
Link: https://github.com/openwrt/openwrt/pull/17790
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adjust wolfssl version for apk by removing the "-stable"
from the OpenWrt version, although it is still needed for
upstream download archive name.
Define PKG_BUILD_DIR accordingly.
Utilize new short version to simplify ABI_VERSION calculation.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16906
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit be952e98bc)
Since commit f1c9afd801 ("ramips: mt7621-dts: mux phy0/4 to gmac1") the
USW-Flex lan1 port has been attached directly to the CPU. This improves
routing performance but hinders switching.
This is a generally accepted trade-off in that commit but for USW-Flex it
is a questionable choice. This switch is designed to deliver PoE to remote
places and using it as a router is unlikely. Meanwhile, the lan1 port is
also PoE-in and will often be the uplink, carrying most of the traffic.
Reverting f1c9afd801 for USW-Flex restores full 1 Gbps switching
performance on all ports.
Signed-off-by: Anders Melchiorsen <amelchio@nogoto.net>
Link: https://github.com/openwrt/openwrt/pull/17703
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 62872f8bfd)
Replace clock patch for eMMC with upstream version to add the tag and
flag them as upstreamed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a9b408a97f)
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b7edf88b0f)
Refresh cpufreq with merged upstream version. Also fix the PM Domain
rebased patch to correctly expose the symbol for non Mediatek target.
Update dtsi with new pm domain name.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit fbbfcbf150)
mbedtls will now automatically append '+crypto' flag when needed.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 2019673ee6)
Import patch "net: phy: realtek: mark existing MMDs as present"
When using Clause-45 mode to access RealTek RTL8221B 2.5G PHYs some
versions of the PHY fail to report the MMDs present on the PHY.
Mark MMDs PMAPMD, PCS and AN which are always existing according to
the datasheet as present to fix that.
Fixes: #16823, #17183, #17232
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
(cherry picked from commit 730db6b893)
Fixed interrupt support for 2.5G PHY.
Removed useless phy-mode on phy node.
Tested on Cudy TR3000.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit 82b69dfaf6)
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Move the nmbm properties outside the partition definition.
Change uppercase to lowercase, add missing read-only flag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit ab375a3484)
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
CC: John Crispin <john@phrozen.org>
Fixes: cfd42a0098 ("ipq40xx: add Intel/Lantiq ATM hacks")
Suggested-by: Andre Heider <a.heider@gmail.com>
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-4-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6d6dc3a3c9)
ATM TC layer have some issues which effectively prevent VRX518 from
being used as ADSL modem. Specifically, there one crash during the ATM
layer configuration and wrong PVC ID selection on packet receiving what
breaks RX path. Fix both of the issues. Make subif iface registration
optional to prevent the crash (see more details in the new patch) and
update the hardcoded PVC ID to match the first allocated channel.
Run tested with FRITZ!Box 7530.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-3-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 470335450e)
It looks like VRX518 returns phys addr of data buffer in the 'data_ptr'
field of the RX descriptor and an actual data offset within the buffer
in the 'byte_off' field. In order to map the phys address back to
virtual we need the original phys address of the allocated buffer.
In the same driver applies offset to phys address before the mapping,
what leads to WARN_ON triggering in plat_mem_virt() function with
subsequent kernel panic:
WARNING: CPU: 0 PID: 0 at .../sw_plat.c:764 0xbf306cd0 [vrx518_tc@8af9f5d0+0x25000]
...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = aff5701e
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Noticed in ATM mode, when chip always returns byte_off = 4.
In order to fix the issue, pass the phys address to plat_mem_virt() as
is and apply byte_off later for proper DMA syncing and on mapped virtual
address when copying RXed data into the skb.
Run tested with FRITZ!Box 7530 on both ADSL and VDSL (thanks Jan) links.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Tested-by: Jan Hoffmann <jan@3e8.eu> # VDSL link
Reported-and-tested-by: nebibigon93@yandex.ru # ADSL link
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-2-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7bd579689d)
the wifi leds of the wax206 were not reacting.
This patch enables the green leds to show activity, as the blue ones are very bright.
Also set the label-mac to the gmac0
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 9ada8578fd)
Supported devices are listed in the metadata as the first part of the
DTS compatible. This normally follows the format "vendor,device".
When updating the device name of the 180W 1920-8G PoE an underscore was
used, instead of a comma, to join the vendor and device name. This will
lead to warnings for users wanting to sysupgrade a device with an older
compatible, as the device's info does not match the one the metadata.
Fixes: 987c96e889 ("realtek: rename hpe,1920-8g-poe to match hardware")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 6a7fa68569)
Fixed an issue where both WAN LEDs light up before plugging in the
ethernet cable and no blinking regardless of WAN network activity.
Updated the LED configuration to reflect proper status:
Green indicates 2.5Gb connection speed.
Yellow indicates other connection speed and traffic activity.
This resolves inconsistent WAN LED behavior on Spectrum SAX1V1K routers.
Signed-off-by: Ivan Deng <hongba@rocketmail.com>
Link: https://github.com/openwrt/openwrt/pull/17623
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8e78bc39a3)
This patch has been accepted for linux v6.14 so we can move it from pending
to backport.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 2f2e21a52b)
These patches have been accepted in linux v6.14 instead of v6.13.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 12a07e934c)
Expose the temperature sensor built-into RTL822x 2.5G and 5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 3a189e3831)
Refresh hack patches with make target/linux/refresh.
Fixes: 9508ca44eb ("kernel: backport improvement to page pool fragment handling from 6.7")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit ee730a66e9)
Makes it easier to keep drivers like mt76 in sync with newer versions
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 9508ca44eb)
(cherry picked from commit 478041997f)
1. Import pending patch to fix ramips/mt7621 64MB targets.
2. Do not enable CONFIG_PAGE_POOL_STATS by default.
Signed-off-by: Danila Romanov <pervokur@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 15887235c1)
Now, that initramfs images built for ZTE devices work, by moving
LZMA_TEXT_START further up the available RAM - same fix works
successfully for Meraki MR18 too. Apply it and reenable initramfs
generation again.
Fixes: 1d49310fdb ("ath79: add Cisco Meraki MR18")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17680
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 7423e67e1b)
This commit fixes Xiaomi AX3000t soft bricks. Issue affects at least rd23
model (Global version) users:
Link: https://forum.openwrt.org/t/openwrt-support-for-xiaomi-ax3000t/180490/452
I also found that these nvram settings are wrong for the rd23 model and
U-Boot erase them:
'''
flag_try_sys1_failed 8
flag_try_sys2_failed 8
'''
As a result, platform.sh -> xiaomi_initial_setup() function sometimes ends
early without applying settings for the rd23 model.
RD03 model strategy:
1. Don't touch values those were set up by platform.sh ->
xiaomi_initial_setup() function
RD23 model strategy:
1. Apply correct nvram settings at every boot
2. Use bulk fw_setenv call
I didn't find opened issue for AX3000t. Similar AX3200 issue:
Link: https://github.com/openwrt/openwrt/issues/16347
So, other Xiaomi devices (e.g. Xiaomi WR30U) may also require fix.
Fixes: 7dbcc1215a ("mediatek: filogic: add support for Xiaomi AX3000T")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17580
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 42a253c7e8)
lldpd was updated, so reset PKG_RELEASE after the PKG_VERSION update.
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit abbec429b4)
Changes (breaking):
- Remove support for building 802.3bt TLVs (broken).
Fix:
- Fix memory leaks in EDP/FDP decoding when receiving some TLVs twice.
- Do not set interface description continuously.
- Use a different Netlink socket for changes and queries.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
Link: https://github.com/openwrt/openwrt/pull/17570
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a18385041e)
047b2efc1348 CMakeLists.txt: bump minimum cmake version
16ff0badbde7 CMakeLists: add support for including ABIVERSION in the library version number
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e046f8c318)
initramfs for some devices grew so big, that it can't be loaded within
the previous 32MB RAM limit. Make the LZMA_TEXT_ADDRESS configurable
per-target once again, to fix it for bigger devices, while maintaining
compatibility with previous ones.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17616
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6720958659)
Define EX5601-T1 and T-56 as alternative name, to explicitly show
the device is supported using existing image. EX5601-T1 does not
have the option to switch between WAN/SFP port. The switch port
is hardwired to the WAN port. The Zyxel T-56 is the odido-branded
version of the EX5601-T1.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17615
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3d63a41ffa)
There is currently a problem where the rootfs in an initramfs image for
single target build is not updated on subsequent run. This is caused by
a bug introduced in d78dec3e19 ("kernel: copy kernel build dir on
Per-Device Initramfs compilation") where the initramfs_data.cpio rm was
moved to PrepareConfigPerRootfs. This caused the side effect of dropping
the rm call for single target build making the kernel reusing the
previous generated initramfs_data.cpio.
To correctly handle this, restore the original location of this call
right after the touch /init call. This way the kernel will always
regenerate the initramfs embedded rootfs ALSO for single target build.
Fixes: d78dec3e19 ("kernel: copy kernel build dir on Per-Device Initramfs compilation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 334c649a8d)
Increase PKG_RELEASE as follow-up for
("lantiq: fritz_cal_extract with reverse option for AVM FritzBox 7430").
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4a8717b5e7)
This implementation of fritz_cal_extract can also retrieve firmware
data stored in reverse byte order, as found in the AVM 7430 device.
This is done by intermediate storage in a buffer presumably large enough
to hold the complete data set. Currently, this buffer size is 128kB + 1kB
(some extra space for skipped data).
In the usual case of "forward" data, this implementation should behave
like the original implementation in all common cases. limit [-l] will
determine the amount of data read and size of buffer allocated.
However, if you are reading reversed data or didn't set a limit, the buffer
may be too small to hold all data. In this case, you can choose a higher
limit [-l] to enforce a sufficient buffer size.
Signed-off-by: Dustin Gathmann <dzsoftware@posteo.org>
Link: https://github.com/openwrt/openwrt/pull/15501
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b2cac2a978)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 144af32b47)
This reverts commit 916af73fc3.
It was reported this change did not fix the reboot issues on AR9344.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 937b5a3e00)
Some VRX518 modems fail to initialize properly with the error message
"dc_ep_clk_on failed". As a result, the DSL data path doesn't work.
This hack, which is based on code from the FRITZ!Box 7530 GPL archive,
fixes the issue. It changes the PCIe vendor/device ID to values matching
a Lantiq SoC. It also appears to emulate a Lantiq CPU ID register for
connected PCIe devices, by remapping the matching address area to a
specially crafted buffer using the address translation unit.
A dedicated compatible is created to activate this in
the device tree, so this shouldn't affect any devices other than
FRITZ!Box 7530/7520.
Original investigation was done in https://github.com/janh/openwrt/commit/59f52125178146a9dc44290c11c63e5e029e8044 which used the "avm,host_magic" property to enabled the patch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/17622
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 676dcb1b2c)
Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.
So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.
Fixes: 75ad5c2414 ("qualcommax: switch to qca8081 upstream PHY driver")
Fixes: #14502
Link: https://github.com/openwrt/openwrt/pull/17656
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 2d077913cd)
These patches have been accepted, so we can move them from pending to
backported.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 7924acdd63)
Import patches to fix several issues with status reporting of RealTek
2.5G PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 41c164d32b)
Add pending PCI patch that should correctly fix mediatek driver with
Airoha SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit f22febae1a)
Backport ETS patch for Airoha ethernet and refresh affected patches.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 67635578fd)
Some platforms a single ethernet device for all ports with multiple rx rings
and NAPI threading enabled. In this case, the steering script was limiting
performance by keeping all NAPI threads assigned to the same CPU.
Fix this by assigning each rx queue and the corresponding NAPI task separately.
Additionally, if the number of rx queues is at least as big as the number of
CPUs, skip weight based assignment and distribute the load across all CPUs
directly.
Fixes: https://github.com/openwrt/openwrt/issues/17611
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit acce25b789)
The package coreutils-stty is not part of the OpenWrt main packages. A
board can not depend on it. Remove the dependency to fix a build problem
seen in the build bots.
Fixes: 8fb805aa1f ("mvebu: Add support for WD Cloud Mirror Gen2")
(cherry picked from commit 717f62d256)
Link: https://github.com/openwrt/openwrt/pull/17589
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
luci-app-attendedsysupgrade expects images to be named
'combined-efi' when the system is using EFI images.
This came about as x86 has 'combined' images for legacy
(BIOS) boot and 'combined-efi' for EFI systems.
armsr images were originally named 'combined' only
as there was no 'legacy' image type.
To avoid special handling in the attendedsysupgrade
code, name EFI images consistent with other targets.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/luci/pull/6430
Link: https://github.com/openwrt/openwrt/pull/12963
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c9ebd4fb30)
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout version).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 51272fcd00)
Bringing up a mesh interface using wpa_supplicant already supports a
per-VIF basic rate selection. Add the same ability when creating a mesh
VIF without wpa_supplicant.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3deeb7805f)
This can be used to configure the base mac address from which all
interface mac addresses are derived
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 00860e485b)
Simplifies setting ifname to a different pattern for all affected
interfaces.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a9ff3ba24b)
When the reset button is next to the SFP cages, I2C operations on the
modules might cause interference on the button's GPIO line. Add a
debounce-interval of 5 times the poll-interval to ensure the line is
actually stable for some time and not just glitching.
This squashes commit 4357f32d41 ("realtek: debounce reset key for
Zyxel GS1900") and commit 777c6106ed ("realtek: move debounce-interval
to correct node").
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The Huasifei WH3000 eMMC model (aka Fudy MT3000) is a Wi-Fi 6 5G
cellular router based on MediaTek MT7981A SoC.
Specifications:
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8G
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
UART: 3.3V, TX, RX, GND / 115200 8N1
Installation via U-Boot rescue:
Connect to the GbE eth port, then press and hold reset button while
booting the device. Wait for the Internet led to blink 5 times,
release reset button. The rescue page is accessible via http://192.168.1.1
Select the OpenWrt sysupgrade image and start upgrade.
Wait for the router to flash new firmware and reboot.
(cherry picked from commit f310b8c74e)
Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 7b9ca01109)
OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.
Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.
Fixes: 5815884c3a ("apm821xx: migrate to DSA")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit e9415be4ad)
Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.
Switches used by individual devices are listed below.
Device Switch PHY
Alpha ASL56026 Lantiq GSWIP int. switch
Arcadyan VG3503J Lantiq GSWIP int. switch
Netgear DM200 Lantiq GSWIP int. switch
TP-LINK TD-W8970 Lantiq GSWIP Lantiq PEF7071V
TP-Link TD-W8980 Lantiq GSWIP Lantiq PEF7071V
Reduces uncompressed kernel size by 16 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 517b9c1cdc)
The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 1b045a7c13)
The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit b2b4ce1532)
Refresh DTS with required changes for cpufreq, MTD and MMC. While at it
also fix wrong speed for MAC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 17b0d1379a)
Replace cpufreq patch with new version requested upstream.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 5069557350)
Add pending patch for ETS qdisc on Airoha ethernet driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53bc763331)
Add patch fixing support for MMC. Additional clock are needed for MMC to
work and some small fixup to make the Mediatek MMC driver on Airoha SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit be5a9ff24b)
Backport patch to support ETS and HTB scheduler for airoha ethernet
driver.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 3ec3ea5316)
Replace BUS clock patch with upstream version with related tag
as it got approved and merged.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 07b49ce876)
Enable MMC and PCI config symbol and refresh config for Airoha AN7581.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 73d368868c)
Updating the driver patches for ipq40xx (correctly) removed the
ethernet0 alias from qcom-ipq4019.dtsi; however, on some devices this
alias is needed for the bootloader to set MAC addresses in the FDT.
As it is unknown which devices actually need the alias, simply add it to
all devices trees for now that enable the &gmac now to avoid regressions
from previous OpenWrt releases. The additional alias should not cause any
issues even when it is not needed.
A TODO comment is added to the same Device Trees to document that the
alias may not be needed (hopefully preventing it from being copied
unnecessarily to newly added devices in the future). The following
devices are known to need the alias for correct MAC address assignment,
so no TODO comment is added:
- FRITZ!Box 4040
- FRITZ!Box 7530
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/17442
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d09dd75fbd)
This patch is needed on bmips since it fixes issues with GPIOs not being
properly configured due to gpio_request_enable not being called on bcm63xx
devices. Therefore we can now drop the bcm63268 gpio function patch.
Backported from f5b1d340be with the exception of
the realtek patch removal.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f5b1d340be)
Basic rates were not set for mesh-interfaces, resulting in the undesired
behavior where 11s frames might be sent with a rate which was not
configured.
Depending on the driver, the basic rate might also be used to determine
the beacon rate configured to the chip. One such example are MediaTek
MT7915 platforms.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ec7f3a512)
According to datasheet, on AR9344 the switch and switch analog need to
be reset first before initiating a full reset.
Resetting these systems fixes spurious reset hangs on Atheros AR9344
SoCs.
Link: https://github.com/freifunk-gluon/gluon/issues/2904
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 916af73fc3)
Hardware:
SoC: MT7981b
RAM: 512 MB
Flash: 256 MB SPI NAND
Ethernet:
1x2.5Gbps (rtl8221b)
WiFi: 2x2 MT7981
Button: Reset
LED: 1x multicolor
Installation
------------
At the moment, firmware installation is only possible via a transition firmware.
It's can be requested from the manufacturer by email to support@cudy.com
Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17225
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6992d6e51a)
I think I implemented the U-Boot handling incorrectly on M30 (saw the issue while porting M60 to OpenWrt). Maybe someone with more U-Boot experience can have a look at it.
What I understood until now:
Before flashing, `sw_tryactive` must be set to 0 because OpenWrt runs on partition 0
During reset after flashing, U-Boot executes the following line:
`boot_rd_auto_sw_img=if itest.s ${sw_tryactive} == 2; then run boot_by_part; else run boot_by_tryactive; fi`
As `sw_tryactive` was set to 0 before flashing, `boot_by_tryactive` will be executed:
`boot_by_tryactive=if itest.s ${sw_tryactive} == 0; then setenv sw_tryactive 2; setenv sw_active 1; saveenv; run ub0; else setenv sw_tryactive 2; setenv sw_active 2; saveenv; run ub1; fi`
As `sw_tryactive` was set to 0 before flashing, `sw_active` will be set to 1 and `ub0` will be executed:
`ub0=setenv bootpart 0; mtkboardboot; run ub0to1; uip main; reset`
If the OpenWrt boot is successful, `ub0to1` and `uip` main will never be executed. Only in case OpenWrt cannot be loaded, `mtkboardboot` will return and the fallback `ub0to1` is executed.
Conclusion: It's sufficient to set `sw_tryacitve` to 0 before flashing, the added code in `target/linux/mediatek/filogic/base-files/etc/init.d/bootcount` is useless.
In the worst case (/proc/cmdline doesn't contain `bootpart=ubi0` as expected), the bootpart variable would be set to 1 and causes starting the firmware from the second partition instead of the one on the first partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17298
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 70610a5240)
Images for certain devices are staring to become too large, as some
device only have 6MB available in their vendor partition layout for the
initial install. This is especially pressing for bootloaders only
supporting gzip compression.
Drop some packages from DEFAULT_PACKAGES that aren't strictly required
for a factory install. The user can always install more packages later
using opkg/apk, or via a sysupgrade to a custom build.
firewall4 is kept to ensure the most recent firewall package is selected
in builds including LuCI.
ethtool is kept as a frequently used diagnostics tool.
Link: https://github.com/openwrt/openwrt/pull/17450
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c9ae39b2d1)
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 2456a2fd7f)
On the AVM 5490/5491, lan1, lan2 and wan ports are connected directly
to the internal GSWIP switch. The lan3 and lan4 ports are connected via
an external QCA8334 switch. This commit adds the missing entries in dts
and adds the driver module.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17473
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 14be320291)
These two packages are SDXC drivers for Mediatek mt762x series SoCs.
One is upstream implementation, and the other is downstream driver.
Installing them together will result in conflicts.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0764e30082)
There are only 5 devices in mt76x8 sub-target selected the MTK SDXC
driver package. And they are all single ethernet port routers or dev
boards:
* LinkIt Smart 7688
* Onion Omega2+
* RAVPower RP-WD009
* VoCore VoCore2
* VoCore VoCore2-Lite
For these devices, they are using the ephy p1 - p4 as the SDXC IO
pins. Therefore, these GPIO pads must be configured in "digital"
IO mode.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f5996ae947)
In the MTK vendor driver, mt762x SDXC registers MSDC_PATCH_BIT and
MSDC_PATCH_BIT1 have different init values than upstream driver.
These magical values should have some help for the stability.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17446
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f70cdfd682)
Correct a few mistakes around dependencies and naming and unset
CONFIG_FIRMWARE_RP1 in RPi5B's config and instead of a builtin, build it
as a module.
Without this change, there are two entries for rp1.ko in
/lib/modules/$(uname -r)/modules.builtin due to how we strip the leading
directories when we generate it. See: package/kernel/linux/Makefile
around line 63.
% grep rp1.ko /lib/modules/$(uname -r)/modules.builtin
pwm-rp1.ko
clk-rp1.ko
rp1.ko
rp1.ko
The kernel log gets spammed with tons of superfluous warnings as a
results of the double entry:
daemon.warn modprobe: found duplicate builtin module rp1
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17461
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit f105d1a9a9)
On some drivers, setting the tx power on the interface is not enough.
Set it for the phy as well.
Fixes: 04fb05914e ("wifi-scripts: add multi-radio config support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit b795e5cbcf)
35bcf68a6297 wifi: mt76: scan: fix setting tx_info fields
4d8d6e2e7710 wifi: mt76: scan: set vif offchannel link for scanning/roc
e354436db440 wifi: mt76: mt7996: use the correct vif link for scanning/roc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f11bc4f201)
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 0eeba04a16)
The ARIA block cipher is pretty uncommon in TLS, deactivate it for now.
This saves some space and reduces the possible variations and attack
vectors of mbedtls.
ARIA support was deactivated in OpenWrt 23.05 by default.
Link: https://github.com/openwrt/openwrt/pull/17342
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3c0ef48bc8)
The commit 7160820d742a ("phy: rockchip: naneng-combphy: fix phy reset")
was backported to kernel 6.6 branch by upstream, however the correspond
dtsi fixes was not, resulting the following error:
```
[ 0.225521] rockchip-naneng-combphy fe830000.phy: error -ENOENT: failed to get phy reset
[ 0.227467] rockchip-naneng-combphy fe840000.phy: error -ENOENT: failed to get phy reset
```
So backport the dtsi fixes here manually.
Fixes: 89b2356b8c ("kernel: bump 6.6 to 6.6.69")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17468
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8a477bafb4)
defer_list skbs held by NAPI can block releasing page pools.
Work around this by scheduling rx softirq on all CPUs while trying to release
a page pool.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 2b70b32aef)
d996988ae55b libubus: close file descriptor after sending it from a request
afa57cce0aff libubus: add support for using channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f0df6e3a4a)
It seems that we have some kind of a symbol name conflict which causes
CONFIG_SECCOMP to always be read as y.
Unfortunatelly, I could not figure out what is causing this, but simply
renaming SECCOMP to USE_SECCOMP seems to properly work and leaves the
symbol unset unless arch dependencies are satisfied.
This fixes qoriq and others that dont support seccomp from failing due
to procd-seccomp package being selected to get included but it cannot be
built for them:
ERROR: unable to select packages:
procd-seccomp (no such package):
required by: base-files-1637~52b6c92479[procd-seccomp]
Fixes: 4c65359af4 ("build: fix including busybox, procd and apk/opkg in imagebuilder")
Link: https://github.com/openwrt/openwrt/pull/17048
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a48ec449cc)
Robert reported, that in firmware images generated by ASU, there is
`apk` package manager missing after the commit 44598c233d ("build:
remove broken dependency of metadata on toplevel .config variables").
That is happening, because apk got removed from `default_packages` list in
`profiles.json`, which is being generated by `json_overview_image_info` Make
target, which uses `scripts/json_overview_image_info.py` helper script,
which gets the information from `DEFAULT_PACKAGES` Make variable.
So lets fix it by providing `DEFAULT_PACKAGES` variable when its needed.
The reason why we didn't added those packages as a dependency to
base-files like any other packages, was to allow disabling them (in
order to save space).
Fixes: #16969
Fixes: openwrt/asu/issues/1084
Fixes: 44598c233d ("build: remove broken dependency of metadata on toplevel .config variables")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Link: https://github.com/openwrt/openwrt/pull/16986
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90f0be8521)
Since the image builder pulls package lists from metadata directly,
add procd and busybox as depdendencies to base-files.
As for the package manager itself, since it can be disabled it needs
to be added directly in the image builder makefile
Fixes: 44598c233d ("build: remove broken dependency of metadata on toplevel .config variables")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 4c65359af4)
Instead of relying on .config symbols for metadata, alter the DEFAULT
variable of affected packages. Fixes enabling opkg vs apk among others.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 44598c233d)
109114146f9c mt76: only enable tx worker after setting the channel
5fe42ec88fd1 mt76: mt7915: ensure that only one sta entry is active per mac address
1884f568ba02 wifi: mt76: do not add wcid entries to sta poll list during MCU reset
71fa9124d107 wifi: mt76: mt7996: fix NULL pointer dereference in mt7996_mcu_sta_bfer_he
eb85bb3fd5bf wifi: mt76: mt7915: fix eifs value on older chipsets
83e4d4a82e65 wifi: mt76: introduce mt792x_config_mac_addr_list routine
b47e20b440ae wifi: mt76: mt7925: fix NULL deref check in mt7925_change_vif_links
3e3c484726f3 wifi: mt76: mt7925: fix wrong band_idx setting when enable sniffer mode
3f1401a0f035 wifi: mt76: mt7925: fix get wrong chip cap from incorrect pointer
eede99f524e8 wifi: mt76: mt7925: fix the invalid ip address for arp offload
c99e4d51b340 wifi: mt76: mt7996: fix overflows seen when writing limit attributes
af983b2543ed wifi: mt76: mt7915: fix overflows seen when writing limit attributes
af494e2dcc94 wifi: mt76: mt7915: exclude tx backoff time from airtime
6f6a1f7cb381 wifi: mt76: mt7996: exclude tx backoff time from airtime
7f65b1b28b4c wifi: mt76: connac: Extend mt76_connac_mcu_uni_add_dev for MLO
1b5e6abc2e7a wifi: mt76: mt7925: Fix incorrect MLD address in bss_mld_tlv for MLO support
72b4688b3912 wifi: mt76: mt7925: Fix incorrect WCID assignment for MLO
6bd2c044e67a wifi: mt76: mt7925: Fix incorrect WCID phy_idx assignment
1c04e9693466 wifi: mt76: mt7925: fix wrong parameter for related cmd of chan info
01e02947bdbf wifi: mt76: mt7925: Fix CNM Timeout with Single Active Link in MLO
b90b1a1dc71b wifi: mt76: mt7925: Enhance mt7925_mac_link_bss_add to support MLO
53ec7a551f17 wifi: mt76: Enhance mt7925_mac_link_sta_add to support MLO
3c99ef40e0e7 wifi: mt76: mt7925: Update mt7925_mcu_sta_update for BC in ASSOC state
285efc6afaec wifi: mt76: mt7925: Update mt792x_rx_get_wcid for per-link STA
e5c0d1289e6c wifi: mt76: mt7925: Update mt7925_unassign_vif_chanctx for per-link BSS
67dcd5c888c4 wifi: mt76: mt7925: Update secondary link PS flow
fd4d6f87072f wifi: mt76: mt7925: Init secondary link PM state
6d972b5b9d6a wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO
3acc6cbb9556 wifi: mt76: mt7925: Cleanup MLO settings post-disconnection
0aab0c61ce92 wifi: mt76: mt7925: Properly handle responses for commands with events
15bead1b0041 wifi: mt76: do not hold queue lock during initial rx buffer alloc
732044a949d5 wifi: mt76: mt7925: config the dwell time by firmware
9ba311ec6afa wifi: mt76: mt7921: introduce CSA support
5d12c7404c22 wifi: mt76: mt7921: add rfkill_poll for hardware rfkill
ef965d408b79 wifi: mt76: mt7925: replace zero-length array with flexible-array member
f8563589c72d wifi: mt76: mt7921u: Add VID/PID for TP-Link TXE50UH
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit bff5260d7b)
Add 1920-24g-poe-180w to the mac address retrieval part of 02_network to
properly set the device's port MAC addresses.
This piece was missed when this device was added.
Fixes: b948c1e39b ("realtek: add support for HPE 1920-24G PoE-180W (JG925A)")
Link: https://github.com/openwrt/openwrt/pull/17460
Signed-off-by: James Sweeney <code@swny.io>
(cherry picked from commit 0b54029a6e)
The extraneous closing parenthesis inside the case matching breaks
syntax of the network initialization script 02_network.
/bin/board_detect: /etc/board.d/02_network:
line 40: syntax error: unexpected newline (expecting ")")
Remove this character so board init is functional again.
Fixes: c8ea1aa970 ("realtek: add support for HPE 1920-24G-PoE-370w")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a3391d871d)
This commit adds kmod-leds-ktd202x to the OpenWrt image for the device
"Acer Connect Vero W6m" which is equipped with one KTD2026 controlling the
device's status LED via I2C.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e44180d45c)
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 56d97fff55)
Hardware information: (largely copied from 11275be)
---------------------
The HPE 1920-24G-PoE+ (180W) (JG925A) is a switch that is
part of the 1920 family which has 180W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (180W):
- PoE chip
- 2 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '180'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: James Sweeney <code@swny.io>
Link: https://github.com/openwrt/openwrt/pull/17444
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit b948c1e39b)
Hardware information:
---------------------
The HPE 1920-24G-PoE+ (370W) (JG926A) is a switch that is
part of the 1920 family wich 370W nominal PoE+ support.
Common with HPE 1920-24G:
- RTL8382 SoC
- 24 Gigabit RJ45 ports (built-in RTL8218B, 2 external RTL8218D)
- 4 SFP ports (external RTL8214FC)
- RJ45 RS232 port on front panel
- 32 MiB NOR Flash
- 128 MiB DDR3 DRAM
- PT7A7514 watchdog
HPE 1920-24G-PoE+ (370W):
- PoE chip
- 3 fans (40mm)
Known issues:
---------------------
- PoE LEDs are uncontrolled.
(Manual taken from f2f09bc)
Booting initramfs image:
------------------------
- Prepare a FTP or TFTP server serving the OpenWrt initramfs image and
connect the server to a switch port.
- Connect to the console port of the device and enter the extended
boot menu by typing Ctrl+B when prompted.
- Choose the menu option "<3> Enter Ethernet SubMenu".
- Set network parameters via the option "<5> Modify Ethernet Parameter".
Enter the FTP/TFTP filename as "Load File Name" ("Target File Name"
can be left blank, it is not required for booting from RAM). Note that
the configuration is saved on flash, so it only needs to be done once.
- Select "<1> Download Application Program To SDRAM And Run".
Initial installation:
---------------------
- Boot an initramfs image as described above, then use sysupgrade to
install OpenWrt permanently. After initial installation, the
bootloader needs to be configured to load the correct image file
- Enter the extended boot menu again and choose "<4> File Control",
then select "<2> Set Application File type".
- Enter the number of the file "openwrt-kernel.bin" (should be 1), and
use the option "<1> +Main" to select it as boot image.
- Choose "<0> Exit To Main Menu" and then "<1> Boot System".
NOTE: The bootloader on these devices can only boot from the VFS
filesystem which normally spans most of the flash. With OpenWrt, only
the first part of the firmware partition contains a valid filesystem,
the rest is used for rootfs. As the bootloader does not know about this,
you must not do any file operations in the bootloader, as this may
corrupt the OpenWrt installation (selecting the boot image is an
exception, as it only stores a flag in the bootloader data, but doesn't
write to the filesystem).
Example PoE config file (/etc/config/poe):
---------------------
config global
option budget '370'
config port
option enable '1'
option id '1'
option name 'lan8'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '2'
option name 'lan7'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan6'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '4'
option name 'lan5'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '5'
option name 'lan4'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '6'
option name 'lan3'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '7'
option name 'lan2'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '8'
option name 'lan1'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '9'
option name 'lan16'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '10'
option name 'lan15'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '11'
option name 'lan14'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '12'
option name 'lan13'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '13'
option name 'lan12'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '14'
option name 'lan11'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '15'
option name 'lan10'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '16'
option name 'lan9'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '17'
option name 'lan24'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '18'
option name 'lan23'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '19'
option name 'lan22'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '20'
option name 'lan21'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '21'
option name 'lan20'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '22'
option name 'lan19'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '23'
option name 'lan18'
option poe_plus '1'
option priority '2'
config port
option enable '1'
option id '24'
option name 'lan17'
option poe_plus '1'
option priority '2'
Signed-off-by: Evan Jobling <evan.jobling@mslsc.com.au>
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Link: https://github.com/openwrt/openwrt/pull/17436
[fix space indentation in DTS]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit c8ea1aa970)
Netgear Orbi devices rely on ethernet0 alias to be present to U-Boot will
populate the MAC.
This fixes the random MAC on each boot after the ethernet0 alias was
dropped from the SoC DTSI.
Fixes: cd9c721124 ("ipq40xx: 6.1: use latest DSA and ethernet patches")
Fixes: #17384
Link: https://github.com/openwrt/openwrt/pull/17414
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 9ea174c7bf)
When doing LTO builds, the target related CFLAGS need to be passed to the
linker, so that they are considered for target code generation.
Pass TARGET_CFLAGS in EXTRA_LDFLAGS to ensure that this is handled properly.
Fixes: #17200
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit e6ce868c3a)
Right now there's no way to know what state CFE will leave the pinctrl
registers in, so they should be explicitly set by linux on boot. This
patch adds a gpio configuration for drivers that need it, i.e. gpio-leds.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[improve patch and fix warnings]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit e44daa4fa5)
This reverts commit 15b21c474e.
The issue seems to appear spuriously.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 84ca1c28f7)
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.67..HEAD
(HEAD -> 811ff707533bcd67cdcd368bbd46223082009b12)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 692205305d)
Add kmods for the following RP1 options that not all users
will necessarily need or want compiled in:
* Composite video
* Display video
* LED control
* PWM control
* Serial video
Build system: x86/64
Build-tested: bcm2712/RPi5B
Run-tested: bcm2712/RPi5B
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17233
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit d6c5805db3)
Conversion to DSA broke 802.2+LLC+SNAP packet processing. Frames
received by napi_complete_done with GRO and DSA have transport_header
set two bytes short, or pointing 2 bytes before network_header &
skb->data. As snap_rcv expects transport_header to point to SNAP
header (OID:PID) after LLC processing advances offset over LLC header
(llc_rcv & llc_fixup_skb), code doesn't find a match and packet is
dropped.
Image built at this commit operates properly:
86dadeba48 - generic: add patch for GPON-ONU-34-20BI quirk
Image built at following commit exhibits the issue:
337e36e0ef - ipq806x: convert each device to DSA implementation
As issue is LLC specific, to avoid impacting non-LLC traffic, and to
follow up on original assumption made on kernel commit fda55eca5a33
("net: introduce skb_transport_header_was_set()") stating "network
stacks usually reset the transport header anyway", llc_fixup_skb to
reset and advance the offset. llc_fixup_skb already assumes the LLC
header is at skb->data, and by definition SNAP header immediately
follows.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17220
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit da7ab64f1f)
Fix bogus reference to kmod-nf-conntrack-timeout, fixing the warning
`WARNING: Makefile 'package/kernel/linux/Makefile' has a dependency on
'kmod-nf-conntrack-timeout', which does not exist`.
Fixes: 0e2dcfc4f4 ("netfilter: add kmod-nfnetlink-ct{helper,timeout}")
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/17388
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 74354fb463)
Regarding SAE support in wifi-station:
Important Note: Unlike PSK wifi-stations, both `mac` and `key` options are required
to make it work. With PSK, hostapd used to perform a brute-force match to find which
PSK entry to use, but with SAE this is infeasible due to SAE's design.
When `mac` is omitted, it will allow any MAC address to use the SAE password if it
didn't have a MAC address assigned to it, but this could only be done once.
The last wildcard entry would be used.
Also, unlike "hostapd: add support for SAE in PPSK option" (commit 913368a),
it is not required to set `sae_pwe` to `0`. This gives it a slight advantage
over using PPSK that goes beyond not needing RADIUS.
Example Configuration:
```
config wifi-vlan
option iface default_radio0
option name 999
option vid 999
option network management
config wifi-station
# Allow user with MAC address 00:11:22:33:44:55 and matching
# key "secretadminpass" to access the management network.
option iface default_radio0
option vid 999
option mac '00:11:22:33:44:55'
option key secretadminpass
config wifi-vlan
option iface default_radio0
option name 100
option vid 100
option network guest
config wifi-station
# With SAE, when 'mac' is omitted it will be the fallback in case no
# other MAC address matches. It won't be possible for a user that
# has a matching MAC to use this network (i.e., 00:11:22:33:44:55
# in this example).
option iface default_radio0
option vid 100
option key guestpass
```
Regarding PSK file creation optimization:
This patch now conditionally runs `hostapd_set_psk_file` depending on `auth_type`.
Previously, `hostapd_set_psk` would always execute `hostapd_set_psk_file`, which
would create a new file if `wifi-station` was in use even if PSK was not enabled.
This change checks the `auth_type` to ensure that it is appropriate to parse the
`wifi-station` entries and create those files.
Furthermore, we now only configure `wpa_psk_file` when it is a supported option
(i.e., psk or psk-sae is used). Previously, we used to configure it when it was
not necessary. While it didn't cause any issues, it would litter `/var/run` with
unnecessary files. This patch fixes that case by configuring it depending on the
`auth_type`.
The new SAE support is aligned with these PSK file changes.
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17145
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 65a1c666f2)
Link: https://github.com/openwrt/openwrt/pull/17248
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Referencing commit a1837135e0
Hardware
--------
SoC: Qualcomm Atheros QCA9558
RAM: 128M DDR2 (Nanya NT5TU64M16HG-AC)
FLASH: 128M SPI-NAND (Spansion S34ML01G100TFI00)
WLAN: QCA9558 3T3R 802.11 bgn
ETH: Qualcomm Atheros QCA8337
UART: 115200 8n1
BUTTON: Reset - WPS - "Router" switch
LED: 2x system-LED, 2x wlan-LED, 1x internet-LED,
2x routing-LED
LEDs besides the ethernet ports are controlled
by the ethernet switch
MAC Address:
use address(sample 1) source
label cc:e1:d5:xx:xx:ed art@macaddr_wan
lan cc:e1:d5:xx:xx:ec art@macaddr_lan
wan cc:e1:d5:xx:xx:ed $label
WiFi4_2G cc:e1:d5:xx:xx:ec art@cal_ath9k
Installation from Serial Console
------------
1. Connect to the serial console. Power up the device and interrupt
autoboot when prompted
2. Connect a TFTP server reachable at 192.168.11.10/24
to the ethernet port. Serve the OpenWrt initramfs image as
"openwrt.bin"
3. Boot the initramfs image using U-Boot
ath> tftpboot 0x84000000 openwrt.bin
ath> bootm 0x84000000
4. Copy the OpenWrt sysupgrade image to the device using scp and
install it like a normal upgrade (with no need to keeping config
since no config from "previous OpenWRT installation" could be kept
at all)
# sysupgrade -n /path/to/openwrt/sysupgrade.bin
Installation from Web Interface
------------
To flash just do a firmware upgrade from the stock firmware (Buffalo
branded dd-wrt) with squashfs-factory.bin
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/17227
(cherry picked from commit 42254d3f5f)
Link: https://github.com/openwrt/openwrt/pull/17359
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
- MT7986 CPU using 2.4GHz and 5GHz WiFi (both AX)
- MT7531 switch
- 512MB RAM
- 128MB NAND flash (MX35LF1GE4AB-Z4I) with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718 (Same as D-Link M30 A1)
- 3 buttons (WPS, reset, LED on/off)
- 1x 2.5 Gbit WAN port with Maxlinear GPY211C
- 4x 1 Gbit LAN ports
Disassembly:
- There are five screws at the bottom: 2 under the rubber feet, 3 under the label.
- After removing the screws, the white plastic part can be shifted out of the blue part.
- Be careful because the antennas are mounted on the side and the top of the white part.
Serial Interface
- The serial interface can be connected to the 4 pin holes next to/under the antenna cables.
- Note that there is another set of 4 pin holes on the side of the board, it's not used.
- Pins (from front to rear):
- 3.3V (do not connect)
- TX
- RX
- GND
- Settings: 115200, 8N1
MAC addresses:
- MAC address is stored in partition "Odm" at offset 0x81 (for example XX:XX:XX:XX:XX:52)
- MAC address on the device label is ODM + 1 (for example XX:XX:XX:XX:XX:53)
- WAN MAC is the one from the ODM partition (for example XX:XX:XX:XX:XX:52)
- LAN MAC is the one from the ODM partition + 1 (for example XX:XX:XX:XX:XX:53)
- WLAN MAC (2.4 GHz) is the one from the ODM partition + 2 (for example (XX:XX:XX:XX:XX:54)
- WLAN MAC (5 GHz) is the one from the ODM partition + 5 (for example (XX:XX:XX:XX:XX:57)
Flashing via OEM web interface:
- Currently not supported because image crypto is not known
Flashing via recovery web interface:
- This is only working if the first partition is active because recovery images are always flashed to the active partition and OpenWrt can only be executed from the first partition
- Use a Chromium based browser, otherwise firmware upgrade might not work
- Recovery web interface is accessible via 192.168.200.1 after keeping the reset button pressed during start of the device until the LED blinks red
- Upload the recovery image, this will take some time. LED will continue flashing red during the update process
- The after flashing, the recovery web interface redirects to http://192.168.0.1. This can be ignored. OpenWrt is accessible via 192.168.1.1 after flashing
- If the first partition isn't the active partition, OpenWrt will hang during the boot process. In this case:
- Download the recovery image from https://github.com/RolandoMagico/openwrt/releases/tag/M60-Recovery-UBI-Switch (UBI switch image)
- Enable recovery web interface again and load the UBI switch image. This image works on the second partition of the M60
- OpenWrt should boot now as expected. After booting, flash the normal OpenWrt sysupgrade image (for example in the OpenWrt web interface)
- Flashing a sysupgrade image from the UBI switch image will make the first partition the active partition and from now on, default OpenWrt images can be used
Flashing via Initramfs:
- Before switching to OpenWrt, ensure that both partitions contain OEM firmware.
- This can be achieved by re-flashing the same OEM firmware version again via the OEM web interface.
- Flashing via OEM web interface will automatically flash the currently not active partition.
- Open router, connect serial interface
- Start a TFTP server at 192.168.200.2 and provide the initramfs image there
- When starting the router, select "7. Load Image" in U-Boot
- Settings for load address, load method can be kept as they are
- Specify host and router IP address if you use different ones than the default (Router 192.168.200.1, TFTP server 192.168.200.2)
- Enter the file name of the initramfs image
- Confirm "Run loaded data now?" question after loading the image with "Y"
- OpenWrt initramfs will start now
- Before flashing OpenWrt, create a backup of the "ubi" partition. It is required when reverting back to OEM
- Flash sysupgrade image to flash, during flashing the U-Boot variable sw_tryactive will be set to 0
- During next boot, U-Boot tries to boot from the ubi partition. If it fails, it will switch to the ubi1 partition
Reverting back to OEM:
- Boot the initramfs image as described in "Flashing via Initramfs" above
- Copy the backed up ubi partition to /tmp (e.g. by using SCP)
- Write the backup to the UBI partition: mtd write /tmp/OpenWrt.mtd4.ubi.bin /dev/mtd4
- Reboot the device, OEM firmware will start now
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17296
(cherry picked from commit b3ce08e0b6)
Link: https://github.com/openwrt/openwrt/pull/17363
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The board has been redesigned due to previous hardware bugs
(with other reasons maybe).
Changes in new board:
- Added a gpio beeper
- Added a Atmel i2c eeprom
- Added a Atmel i2c ECC accelerator
- Added a Philips RTC module
- Added two RS485
- Removed WPS button
- Replaced USB3 port with M.2 B-key for LTE modules
- Swapped GbE LEDs gpio
Also assigned wifi mac with nvmem binding, added iface setup for failsafe,
increased phy assert time for rtl8221b, and updated LED labels.
Keeping compatibility for old version is not necessary here as only
few samples were sent to those interested in it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17253
(cherry picked from commit 5a7fb834c7)
Link: https://github.com/openwrt/openwrt/pull/17348
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
4GB LPDDR4X RAM
2x 2500 Base-T (PCIe, rtl8125b)
4x LEDs (POWER / SATA1 / SATA2 / SATA3)
32GB eMMC on-board
Micro-SD Slot
HDMI OUT
2x USB 2.0 Port
3x SATA Slot
DC Jack 12V
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <i@cnsztl.eu.org>
(cherry picked from commit 934bf398be)
The kernel logs the error "bcm6368_nand 10000200.nand: there is not valid
maps for state default" on boot and all nand pins show as UNCLAIMED in
sysfs pinmux-pins.
bcm6362.dtsi, bcm6368.dtsi and bcm63268.dtsi use the undocumented property
group which the driver doesn't understand. This has been documented upstream
in commit caf963efd4b0b9ff42ca12e52b8efe277264d35b.
Replacing group with pins allows the nand pins to be properly configured.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[add bcm636/bcm6368 and fix commit title]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit d1e9c50d06)
The GS1900 images have been updated to have a larger firmware partition,
bumping the compatibility version to 2.0. However, since this version is
generated on first boot and the default was used, these images still
advertised 1.0 after a fresh install.
Add a new uci-defaults script that will generate the correct version for
all affected Zyxel GS1900 devices.
Fixes: 35acdbe909 ("realtek: merge Zyxel GS1900 firmware partitions")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit a25809a474)
Fixes the following error by backporting upstream update:
```
scripts/dtc/pylibfdt/libfdt_wrap.c: In function ‘_wrap_fdt_next_node’:
scripts/dtc/pylibfdt/libfdt_wrap.c:5581:17: error: too few arguments to function ‘SWIG_Python_AppendOutput’
5581 | resultobj = SWIG_Python_AppendOutput(resultobj, val);
| ^~~~~~~~~~~~~~~~~~~~~~~~
```
Fixes: https://github.com/openwrt/openwrt/issues/17345
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/17352
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 4e68103c4e)
The boards where renamed, but BUILD_DEVICES was not adapted. This
variable points to the board name. Without this change the u-boot
binaries are not selected in the configuration.
Copy the u-boot binaries under the BUILD_DEVICES name as it is expected
by the image scripts.
Fixes: 33e23e8922 ("build: d1: add SUPPORTED_DEVICES")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit af6c1f9497)
The dual-boot partition layout for the Zyxel GS1900 switches results in
6.9MB for both kernel and rootfs. Depending on the package selection,
this may already leave no space for the user overlay.
Merge the two firmware partitions, effectively dropping dual boot
support with OpenWrt. This results in a firmware partition of 13.9MB,
which should leave some room for the future.
To maintain install capabilites on new devices, an image is required
that still fits inside the original partition. The initramfs is used as
factory install image, so ensure this meets the old size constraints.
The factory image can be flashed via the same procedure as vendor images
when reverting to stock, can be installed from stock, or can be launched
via tftpboot.
Link: https://github.com/openwrt/openwrt/issues/16439
Link: https://github.com/openwrt/openwrt/pull/16442
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 35acdbe909)
GPIO 5 on the RTL8231 is defined reset the system, but fails to actually
do so. This triggers a kernel a number of warnings and backtrace for
GPIO pins that can sleep, such as the RTL8231's. Two warnings are
emitted by libgpiod, and a third warning by gpio-restart itself after it
fails to restart the system:
[ 106.654008] ------------[ cut here ]------------
[ 106.659240] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 106.826218] ---[ end trace d1de50b401f5a153 ]---
[ 106.962992] ------------[ cut here ]------------
[ 106.968208] WARNING: CPU: 0 PID: 4279 at drivers/gpio/gpiolib.c:3098 gpiod_set_value+0x7c/0x108
[ Stack dump and call trace ]
[ 107.136718] ---[ end trace d1de50b401f5a154 ]---
[ 111.087092] ------------[ cut here ]------------
[ 111.092271] WARNING: CPU: 0 PID: 4279 at drivers/power/reset/gpio-restart.c:46 gpio_restart_notify+0xc0/0xdc
[ Stack dump and call trace ]
[ 111.256629] ---[ end trace d1de50b401f5a155 ]---
By removing gpio-restart from this device, we skip the restart-by-GPIO
attempt and rely only on the watchdog for restarts, which is already the
de facto behaviour.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
(cherry picked from commit 2ada95ccdf)
The AR8035 PHY is used in most Octeon boards supported by OpenWRT (all
the Ubiquiti routers at least). To be able to use its PHY-specific
functionality (cable testing, LED Control, ...) it should be built on
Octeon. It also needs the regulator framework, so enable that as well.
These boards are not space-constrained, so this really has no downsides.
Tested on an EdgeRouter Lite, cable tests now work with ethtool-full.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Link: https://github.com/openwrt/openwrt/pull/17318
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 4892ea9a74)
This backport patch inserted suspend/resume callbacks
for the wrong PHY driver.
The fixed patch is needed for Huawei AP5030DN
to initialize its second PHY.
Refresh all affected patch with make target/linux/refresh.
Fixes: 06cdc07f8c ("ath79: add support for Huawei AP5030DN")
Signed-off-by: Marco von Rosenberg <marcovr@selfnet.de>
Link: https://github.com/openwrt/openwrt/pull/17312
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d7f638bc69)
Don't fail wireless interface bringup on empty PSK set. This is a valid
configuration, resulting in a PSK network which can't be connected to.
It does not fail the bringup of the hostapd process.
Keep failing the interface setup in case a password with invalid length
is used.
This is also beneficial when intending to configure a PPSK network. It
allows to create a network where no PPSK is yet set.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 17a71f0c154cebd2e52cd8407531a9a88c931474)
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
(cherry picked from commit e63326e26a)
Link: https://github.com/openwrt/openwrt/pull/17303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
access to undeclared variable radio In [anonymous function](), file /usr/share/hostap/hostapd.uc, line 830, byte 45:
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit 31e45f62ca)
e00958884416 fw4: do not add physical devices for soft offload
dfbcc1cd127c fw4: skip not existing netdev names in flowtable device list
18fc0ead19fa init: use the reload data trigger to reload firewall on procd data changes
Fixes: https://github.com/openwrt/openwrt/issues/13410
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 47c75a25cd)
93461ca4c827 unet-cli: only apply defaults on create
3e5766783d5d unet-tool: add support for confirming password
074d3659ca4a unet-cli: confirm password when creating new seed based key
bf3488a3807a unet-cli: add add/set-local-host command
9eb57c528461 unet-cli: add support for setting interface zone
a0a2d80f3459 ubus: add firewall rules for network port/pex_port via procd
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit f077e058fd)
This can be useful to reload the firewall when procd firewall data changes
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 49d92d3e93)
Allows a running servie to manage its own data if untouched by the init script
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 8c5826b140)
2e206dbe77ec service: add support for triggers on service/instance data changes
735b48728fca service: remove leftover lines from previous commit
32469644a029 service: allow incremental changes to service properties
fd01fb852302 service: fix double free bug when dealing with data
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 3d900bd055)
e2f05de state: set_stdio: chdir back to / in case of failure
30542c9 inittab: Disable implicit controlling TTY.
Signed-off-by: John Crispin <john@phrozen.org>
(cherry picked from commit 2bcc49aef9)
058a099f5bc5 interface: fix memleak and reload issue for the zone attribute
ea01ed41f321 interface: remove unnecessary NULL checks before free()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 53e312e193)
d22d7db581d5 bpf_skb_utils.h: add missing include to fix build against newer kernel headers
bbd3e0eb1419 host: fix peer routes on a node acting as gateway
b17164751fc7 unet-tool: add support for generating keys from salt + seed passphrase
041e05870c20 unet-tool: add support for dumping pubkey from signed file
b58920d420cb unet-tool: add support for extracting network data from signed bin file
f335f5b40b4e unet-cli: add support for generating key from seed
8b1f1d099352 unet-cli: add support for importing networks from signed data
188ba05eadf2 unet-cli: add missing command line help for import
8f15fc306a40 unet-cli: fix add-ssh-host with seed keys
486bc3b86dc2 pex-msg: enable broadcast for global PEX socket
e4a24cdfbc1c unet-cli: fix defaults on create
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit af1740a28b)
The KuWFi N650 is a 5GHz outdoor wireless bridge based on QCA9563.
Specs
=====
CPU: QCA9563, 775MHz
RAM: 128MiB
Flash: 16MiB
Wireless: QCA9888 (5GHz only)
Ethernet: 2x GBit (via QCA8337), 48V passive PoE
Installation
============
From OEM firmware
-----------------
The OEM firmware has telnet enabled by default. If not, it can be enabled
from the firmware web interface. You need a TFTP server on your computer
and the OpenWrt factory image should be available as "n650factory.bin".
It is assumed that your computer has the IP 192.168.1.1 and the N650
192.168.1.20 (default IP address).
1. Connect via Telnet to the device and log in with the default credentials
"admin:admin"
2. Exploit the limited interface by typing "ps & /bin/sh"
3. Press <ENTER> to start the shell
4. Enter the following commands:
$ cd /tmp
$ tftp -r n650factory.bin -g 192.168.1.1
$ cat << EOF > /tmp/openwrt.sh
IMAGE_NAME="\$1"
if [ ! -e \${IMAGE_NAME} ]; then
echo "Image file not found: \${IMAGE_NAME}"
exit 1
fi
. /usr/sbin/common.sh
kill_remaining TERM
sleep 3
kill_remaining KILL
run_ramfs mtd write \${IMAGE_NAME} firmware
sleep 2
reboot -f
EOF
$ chmod +x /tmp/openwrt.sh
$ /tmp/openwrt.sh n650factory.bin
Once the device reboots, it should load OpenWrt.
From UART
---------
UART installation is possible since the serial header is already soldered
on. The pinout is GND - Tx - Rx - VCC from top to bottom (RJ45 ports are
at the bottom). Connect with 115200 8N1.
First, boot OpenWrt from TFTP. Enter the following commands in the U-Boot
shell, assuming your computer has the IP address 192.168.1.1 and a TFTP
server running where the initramfs image is provided as n650.bin:
setenv ipaddr 192.168.1.20
setenv serverip 192.168.1.1
tftpboot 0x84000000 n650.bin
bootm
Once booted, transfer -loader.bin and -sysupgrade.bin images to the device
at /tmp. Enter the following commands, replacing the filenames:
mtd write /tmp/loader.bin loader
sysupgrade /tmp/sysupgrade.bin
Reboot and OpenWrt should load from flash.
Back to Stock
-------------
Back to stock is only possible if you saved a partition backup before
installing OpenWrt. Assuming you have fullbackup.bin covering the whole
flash, you need to prepare the image as follows:
$ dd if=fullbackup.bin of=fwconcat0.bin bs=65536 skip=4 count=212
$ dd if=fullbackup.bin of=loader.bin bs=65536 skip=216 count=1
$ dd if=fullbackup.bin of=fwconcat1.bin bs=65536 skip=217 count=22
$ cat fwconcat0.bin fwconcat1.bin > firmware.bin
Transfer firmware.bin and loader.bin to the OpenWrt device. First, flash
loader.bin to mtd device loader, then force sysupgrade:
$ mtd write loader.bin loader
$ sysupgrade -F firmware.bin
The reason for the two-step process is the way the flash layout is designed
for OpenWrt in contrast to the OEM firmware partition.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/17089
Link: https://github.com/openwrt/openwrt/pull/17247
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit dde510cf97)
The initialization of mesh interfaces currently fail when wpa_supplicant
is not installed. This is due to the script calling the wpa_supplicant
feature indicator without verifying wpa_supplicant is installed at all.
To avoid failing, first check if wpa_supplicant is installed before
determining the available featureset.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1be18c6daa)
86da5cbcdb9d system-linux: do not pull ifindex/flags from netlink messages on rtnl events
cd96f61ba63e proto-shell: fix spurious interface teardowns with host deps
a39fe3a8b150 wireless: add support for adding a list of devices for a wifi-iface
d29cf707478c iprule: add ipproto property
768027c5a764 system-linux: restore reading flags from netlink messages
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17074
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit f4492b6b1c)
Link: https://github.com/openwrt/openwrt/pull/17110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The device path to the devices changed. Migrate the wifi
configurations from the old path to the new one. This is needed to
migrate Wireless configurations from OpenWrt 23.05 to OpenWrt 24.10.
This script is based on these two files:
target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
target/linux/qualcommax/ipq807x/base-files/etc/hotplug.d/ieee80211/05-wifi-migrate
Fixes: 0ef9274721 ("mediatek: filogic: move mt7981 on-SoC blocks to "soc" node in DT")
Fixes: https://github.com/openwrt/openwrt/issues/17174
Link: https://github.com/openwrt/openwrt/pull/17210
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit f8b93e2d12)
libbfd feature is not used when building eBPF program, and it makes bpftool fail to build in a clean environment, since binutils in toolchain have libbfd disabled.
Signed-off-by: Eric Long <i@hack3r.moe>
Link: https://github.com/openwrt/openwrt/pull/17073
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3d8d81883f)
Backport support for RTL8812AU/RTL8821AU USB adapters
Manually backported patch:
045-v6.13-wifi-rtw88-Enable-the-new-RTL8821AU-RTL8812AU-driver
Patches from 046 to 051 are pending.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
[Move BPAUTO_WANT_DEV_COREDUMP to original patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 36f6d6ddcd)
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 1b6f7ec679)
Recent changes to BuildBot config moved the kmods to a dedicated
directory and dropped them from the packages dir. This was needed as
both OPKG and APK gets confused if both entry are present.
To fix this, unconditionally append the kmod feed line if
CONFIG_BUILDBOT is enabled.
Fixes: #17146
Link: https://github.com/openwrt/openwrt/pull/17151
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 53ee2e8c03)
This reverts commit 70e41d0205.
"ethaddr" is stored into the "u-boot-env" (stock: "Config") partition
and it's quoted with double-quotations, but that format is not supported
by the current NVMEM u-boot-env driver (and mac_pton() function) and the
MAC address won't be parsed to byte array.
This causes random MAC addresses on the adapters, so revert the above
commit.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17116
(cherry picked from commit af611bce44)
Link: https://github.com/openwrt/openwrt/pull/17117
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove backtick from gdb description text, as that seems to
be recognized as a shell action by compilation with apk,
causing error.
Example from test buildbot:
rstrip.sh: /builder/shared-workdir/build/sdk/build_dir/target-aarch64_generic_musl/gdb-15.2/ipkg-aarch64_generic/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
bash: -c: line 2: syntax error: unexpected end of file
make[3]: *** [Makefile:123: /builder/shared-workdir/build/sdk/bin/packages/aarch64_generic/base/gdb-15.2-r1.apk] Error 2
Local compilation:
rstrip.sh: /OpenWrt/aarch64/build_dir/target-aarch64_cortex-a53_musl/gdb-15.2/ipkg-aarch64_cortex-a53/gdb/usr/bin/gdb: executable
bash: -c: line 1: unexpected EOF while looking for matching ``'
make[2]: *** [Makefile:123: /OpenWrt/aarch64/bin/packages/aarch64_cortex-a53/base/gdb-15.2-r1.apk] Error 2
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/16908
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit adb921c34f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds OpenWrt U-Boot layout support for Routerich AX3000. The
aims:
1. Get open-source U-Boot;
2. Get maximum available free space in OpenWrt.
Install
-------
1. Copy OpenWrt ubootmod-bl31-uboot.fip, ubootmod-preloader.bin, to the
/tmp folder of the router using scp.
2. Make mtd partitions backups:
http://192.168.1.1/cgi-bin/luci/admin/system/flash -> Save mtdblock
contents
3. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```
4. Write FIP and preloader:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/ubootmod-preloader.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/ubootmod-bl31-uboot.fip FIP
```
5. Copy OpenWrt ubootmod-initramfs-recovery.itb to the tftp server root
with IP 192.168.1.254.
6. Reboot router:
```
reboot
```
U-Boot will automatically download from the tftp server and boot OpenWrt
initramfs system.
7. Copy OpenWrt ubootmod-squashfs-sysupgrade.itb to the /tmp dir of the
router using scp.
8. Run sysupgrade:
```
sysupgrade -n /tmp/squashfs-sysupgrade.itb
```
Recovery
--------
1. Place OpenWrt initramfs-recovery.itb image (with original name) on the
tftp server (IP: 192.168.1.254).
2. Press "reset" button and power on the router. After ~10 sec release the
button.
3. Use OpenWrt initramfs system for recovery.
BL2 and FIP recovery
--------------------
Use mtk_uartboot and UART connection if BL2 or FIP in UBI is destroyed:
Link: https://github.com/981213/mtk_uartboot
Return to stock:
----------------
1. Copy partition backups (BL2.bin and FIP.bin) to the /tmp dir of the
router using scp.
2. Install kmod-mtd-rw:
```
opkg update && opkg install kmod-mtd-rw
```
3. Restore stock U-Boot and reboot:
```
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd erase BL2
mtd write /tmp/BL2.bin BL2
mtd unlock FIP
mtd erase FIP
mtd write /tmp/FIP.bin FIP
reboot
```
4. Open U-Boot web recovery, upload stock firmware image and start
upgrade.
Link: http://192.168.1.1
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16791
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d413163832)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Deactivate CONFIG_CONTEXT_TRACKING_USER_FORCE: Force user context
tracking: This is a testing feature which should not be activate in
production environments according to the Kconfig help. It adds an extra
overhead.
Deactivate CONFIG_RCU_NOCB_CPU_DEFAULT_ALL: Offload RCU callback
processing from all CPUs by default: This option should only be used in
aggressive HPC or real-time workloads which we do not have in OpenWrt.
For normal workloads it increases the number of context switches.
In the default Arch Linux kernel both options are not activated.
Fixes: 31111680f6 ("x86: switch config to a tickless kernel")
Link: https://github.com/openwrt/openwrt/pull/17057
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ed52345445)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to enter the U-Boot shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000s.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000s.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Signed-off-by: David Ignjic <ignjic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit faf4b3e0f7)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit adds support for two variants of the already supported router
Acer Predator Connect W6: The Acer Predator Connect W6d (W6 without 6 GHz
wifi) and the Acer Connect Vero W6m (W6 without 2.5G eth1 port, usb3 port,
and the 6 on-board gpio RGB LEDs, and with a KTD2026 RGB LED controller
instead of the KTD2061 LED controller of the W6/W6d).
The device tree for the W6m refers to the KTD202x driver suggested in
PR #16860.
Patching target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
removes the code repetition in (old) lines 121 to 124 on the occasion.
This is the last of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 2898d1d126)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare for OpenWrt support other Acer W6 devices and to get
a step further to full hardware support for Acer Predator Connect W6, this
commit
- adjusts the product name ("Acer Predator Connect W6")
- updates gpio LED labels to function/color scheme
- show router status by using first rgb led instead of it's red color only
(blue: booting/failsafe mode; red: sysupgrade; green: running – was: red)
- changes switch/eth1 led configuration to reflect RX/TX activity and speed
(green: full 1Gbps/2.5Gbps speed; amber: lower speed; blink: RX/TX)
- shortens dummy dm-mod.create string in bootargs
- enables W6's i2c interface
This is the third of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit d42075dcef)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices and to adapt
the procedure to read and set mac addresses which other devices of the same
target are using (instead of needing an additional script and creating an
additional structure in the file system), this commit
- reads device mac addresses from u-boot environment
- avoids the detour via the file system to set the mac addresses
- drops redundant file /lib/preinit/05_extract_factory_data.sh
The idea and the implementation were thankfully taken from PR #16410.
This is the second of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit e7aaba2587)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In order to prepare OpenWrt support for other Acer W6 devices, this commit
moves all device tree components that are used by all Acer W6/W6e/W6d/W6m
routers from mt7986a-acer-predator-w6.dts to mt7986a-acer-w6-common.dtsi
(new file) and includes this dtsi file in mt7986a-acer-predator-w6.dts.
Minor changes had to be made to the device tree in order to improve clarity
and – notably – to reduce the number of dtc warnings:
- replace (obviously wrong) led@<N> gpio led entities by led-<N>
- remove unnecessary (default-state = "off") gpio led statements
- rename entity “memory” to “memory@0”
- add missing #address-cells and #address-size in /soc/mmc@11230000
- add missing #address-cells and #address-size in /soc/pcie@11280000
- introduce symbols “nvmem” and “swport0” in dtsi (referenced in dts)
The changes were checked with `diff -BEZbdtwy --suppress-common-lines ...`
(comparing two dts files created using old and new fdt-1 blobs again), see
https://github.com/openwrt/openwrt/pull/16861/#issuecomment-2455680020 .
This is the first of four commits into which the original commit was split
to make reviews easier and more targeted.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16861
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit ce3b36b3d5)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
TP-Link CPE710-v2 is an outdoor wireless CPE for 5 GHz with one Ethernet
port based on the AP152 reference board. Compared to the CPE710-v1, the
only change observed in hardware is that the mdio address of the ethernet
physical changed from 0x4 to 0x0.
Specifications:
- SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz
- RAM: 128MiB DDR2 @ 650MHz
- Flash: 16MiB SPI NOR Based on the GD25Q128
- Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless
data rate), based on the QCA9896
- Ethernet: one 1GbE port
- 23dBi high-gain directional 2×2 MIMO parabolic antenna
- Power, LAN, WLAN5G Blue LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI or through TFTP
To get to TFTP recovery just hold reset button while powering on for around
30-40 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP address:192.168.0.254
Signed-off-by: Tim Noack <tim@noack.id>
Link: https://github.com/openwrt/openwrt/pull/16637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5572e0196a)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Zbtlink ZBT-WE2426-B is an indoor dual band WiFi router
with 4 external non detachable antennas and 5 Fast Ethernet ports.
Hardware of ZBT-WE2426-B:
- SoC: MT7628AN
- RAM: 64 MB (Winbond W9751G6K8-25)
- Storage: 8 MB SPI flash (S25FL064K)
- Ethernet: 5x 10/100 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz: on SoC (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 8x
- Buttons: 1x reset
- USB: 1x 2.0
- MicroSD slot: 1x
- Power: 9 VDC, 1 A
- Uart: GND TX RX PWR - J1 on the PCB
- Board silkscreen: "ZBT-WE2426-C V04" "2018-02-28" "CTT" "13 18"
Backup the stock firmware, settings and calibration data:
This router comes with PandoraBox OpenWrt firmware, so it is
possible to get all MTD partitions using scp.
Installation:
- Using the bootloader web server. Hold the reset button while turning
the power on. Upload the sysupgrade image on http://192.168.1.1.
- Using the sysupgrade command in PandoraBox OpenWrt.
LEDs:
- LAN1,LAN2,LAN3,LAN4,WAN,WLAN2G use GPIO pins of the MT7628AN SoC
(GPIOs 43,42,41,40,39,44)
- WLAN5G uses pin of MT7612EN.
- The POWER LED is directly connected to the VCC. It can be reconnected to
the GPIO 37 of the MT7628AN SoC by resoldering SMD resistor on the PCB.
Buttons:
- The RESET button is connected to the GPIO 38 of the MT7628AN SoC.
MAC addresses as verified by OEM firmware:
use address source
2g *:b0 factory 0x4 (label)
5g *:b1 factory 0x8004
LAN *:b2 factory 0x28
WAN *:b3 factory 0x2e
Signed-off-by: Vaclav Svoboda <svoboda@neng.cz>
Link: https://github.com/openwrt/openwrt/pull/16927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3a9752ea02)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 5eb25dddb1)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
New stm32 target introduces support for stm32mp1 based devices.
For now it includes an initial support of the STM32MP135F-DK device.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP135FAF7
RAM: 512 MiB
Storage: SD Card
Ethernet: 2x 100 Mbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
Buttons: 1x Reset, 1x User (USER2)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 851e7f77e4)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Popular bpi-r3 pwm fans like this one
https://www.amazon.com/youyeetoo-Barebone-Fan-BPI-R3-Integrated/dp/B0CCCTY8PS
will not work properly with current openwrt-23.05/24.10 firmware.
Trying different pwm setting
echo $value > /sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1
I found:
pwm1 value fan rotation speed cpu temperature notes
-----------------------------------------------------------------
0 maximal 31.5 Celsius too noisy
40 optimal 35.2 Celsius no noise hearable
95 minimal
above 95 does not rotate 55.5 Celsius
-----------------------------------------------------------------
At the moment we have following cooling levels:
cooling-levels = <255 96 0>;
for cpu-active-high, cpu-active-medium and cpu-active-low modes correspondingly.
Thus only cpu-active-high and cpu-active-low are usable. I think this is wrong.
This patch fixes cpu-active-medium settings for bpi-r3 board.
PS: I know, the patch is not ideal as it can break pwm fan for some users.
There are some peoples that use handmade cooling solutions, but:
* discussed cooler is the only 'official' pwm cooler for bpi-r3
available on the market.
* most peoples will use passive cooling available on the market or
the discussed cooler.
* the pwm-fan dts section was added before the official cooler
appears on the market.
Thus it should not be a lot of harm from this fix.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16974
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 3467ea905b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Now that omnia-eeprom is marked nonshared building the cortex-a9 mvebu
subtarget will fail with:
ERROR: unable to select packages:
omnia-eeprom (no such package):
required by: world[omnia-eeprom]
This is because omnia-eeprom depends on TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia
which will not be satisfied in buildbots since CONFIG_TARGET_ALL_PROFILES
and CONFIG_TARGET_PER_DEVICE_ROOTFS are set in which case
CONFIG_TARGET_mvebu_cortexa9_DEVICE_cznic_turris-omnia is not set.
So, lets simply depend on the mvebu/cortex-a9 subtarget.
Fixes: 371e7bef40 ("omnia-eeprom: Mark it nonshared")
Link: https://github.com/openwrt/openwrt/pull/17007
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 90de3b277b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Note that the old ad-hoc method did not explicitly align backup data
to 64 KiB boundaries.
Also note that the qnap 301w has a 'rootfs_data' partition in the eMMC
that is being ignored by fstools during boot, presumably due to a bug.
This is why the partition is also ignored in the sysupgrade code and
there is no definition of CI_DATAPART="rootfs_data".
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit fe481c9c47)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
On aarch64 musl gcc 14.x compiler, trying compiling elfutils 0.192 with
lto option enabled will cause null-dereference error.
Example error message:
...
elf_compress.c: In function 'elf_compress':
elf_compress.c:675:26: error: potential null pointer dereference [-Werror=null-dereference]
675 | shdr->sh_flags |= SHF_COMPRESSED;
| ^
elf_compress_gnu.c: In function 'elf_compress_gnu':
elf_compress_gnu.c:127:25: error: potential null pointer dereference [-Werror=null-dereference]
127 | shdr->sh_size = new_size;
| ^ ^
...
This is a false postive warning but will abort compilation if gcc has
`-Werror` flag. This commit add a patch for this, see the bugzilla
report below.
This commit backports a series of patches to fix some errors.
Add patch:
- 007-add-libeu-symbols-to-libelf.patch
- 008-fix-autoconf-ENABLE_IMA_VERIFICATION.patch
- 009-fix-null-dereference-with-lto.patch
Link: https://sourceware.org/bugzilla/show_bug.cgi?id=32311
Signed-off-by: Ryan Keane <the.ra2.ifv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16886
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit afffcd09e5)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently, libreadline only installs
```
/usr/lib/libhistory.so.8 -> libhistory.so.8.2
/usr/lib/libhistory.so.8.2
/usr/lib/libreadline.so.8 -> libreadline.so.8.2
/usr/lib/libreadline.so.8.2
```
But there is no `libreadline.so` or `libhistory.so` available.
So this happens:
```
root@OpenWRT:~# cat a.c
int main() {
}
root@OpenWRT:~# gcc a.c -lreadline
/usr/bin/ld: cannot find -lreadline: No such file or directory
collect2: error: ld returned 1 exit status
```
Unless, of course, one uses `-l:libreadline.so.8`... But that
doesn't help with binaries that try to dynamically open
`libreadline.so`. I have one of those here (the STklos Scheme
compiler -- I didn't make a PR for it because it's far from
being ready, but one issue is that it does use dlopen to use
readline...)
With the symlink, it works:
```
root@OpenWRT:~# ln -s /usr/lib/libreadline.so.8 /usr/lib/libreadline.so
root@OpenWRT:~#
root@OpenWRT:~# gcc a.c -lreadline
root@OpenWRT:~#
```
Another example: when trying to package rlwrap, the build failed
complaining it could not find readline (using `-lreadline`).
It would then be necessary to change rlwrap's `configure.ac`
(and also in all packages that use readline), but it seems
simpler to add the symlinks...
This PR changes the Makefile so it will include the links.
Signed-off-by: Jeronimo Pellegrini <j_p@aleph0.info>
Link: https://github.com/openwrt/openwrt/pull/16445
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 0000ba6ab8)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit fixes and closes#16313.
Switch the x86 kernel's timer to tickless operation which is
more power efficient since it is not woken up by periodic timer
interrupts when idle. Also add several other options for CPU
idle governors particularly the upstream default for tickless
kernels, CONFIG_CPU_IDLE_GOV_MENU. Without this commit, my AMD
Ryzen 7 5800U can only achieve a minimum core frequency of 1,384
MHz which is over 3x higher than the processor's minimum
frequency of 400 MHz which is accessible with this modification.
In addition to the lower clock rate, I have seen a concomitant
reduction in both idle temps and at-the-wall power consumption.
Summary:
* Idle CPU freqs dropped from 1,384 MHz to 400 Mhz.
* Idle power consumption dropped from 7 W avg to 5 W.
* Idle temps have dropped from 50C on avg to 43C.
There are other well known reasons to switch to a tickless
timer including: reduced interrupt overhead, better use of CPU
resources, and reduced latency to name a few.
Build system: x86/64
Build-tested: x86/64/AMD Cezanne
Run-tested: x86/64/AMD Cezanne
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/16317
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 31111680f6)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Change the package name from intel-igpu-firmware-* to i915-firmware-*,
the prefix "intel-igpu" is misleading, i915 firmware is not only for
iGPU but also for dGPU now.
Remove the redundant "intel" as i915 is already well known.
More accurate file classification to handle following files correctly:
adlp_dmc.bin
mtl_huc.bin
mtl_huc_gsc.bin
mtl_gsc_1.bin
The pattern in regex is "([[:alnum:]]+)_([[:alnum:]]+)(_[\w-.]+)?\.bin",
where $1 is the platform, $2 is the firmware type (dmc, guc, huc, etc.),
and the optional $3 which is revision or other suffix.
Glob first to narrow down the target file set, and then split with "_"
to extract the firmware type (remove the ".bin" in case there is no $3)
Add package "i915-firmware" as a meta package to install all the i915
firmwares, it is a balance between simplicity and optimization.
* Installing all the available firmwares as a whole, can support all the
platforms, not only the current one but also the future ones. The
price to pay is the increased size.
* If we want to minimize the storage, we can customize to install the
necessary ones only, even for the target platform only (e.g. ADL) and
skip the others. The price to pay is the time to tune.
What I am going to do is:
* Let drm-i915 driver depend on i915-firmware-dmc, which is small and
can cover most of the old platforms
* Let the user select i915-firmware to install all the i915 firmwares as
a whole to cover the latest or future platforms
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit ca00bafd7e)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add a new utility, `omnia-eeprom`, which can be used to print / set
EEPROM fields on Turris Omnia.
One example when this utility might be useful is if the board
experiences random crashes due to newer versions of the DDR training
algorithm in newer U-Boot. The user can change the DDR speed from 1600K
to 1333H to solve these issues, with
```
omnia-eeprom set ddr_speed 1333H
```
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16264
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 749a43325b)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
The re-branded device comes with OpenWrt preinstalled, and an OpenWrt-based
U-Boot bootloader version. While the flash layout has been kept compatible
with the OpenWrt version found on the stock device (see [5]), the image format
changed, making a bootloader upgrade necessary.
Specifications:
SoC: Mediatek MT7981BA
RAM: 256MB
Flash: SPI-NOR 32 MiB (Winbond W25Q256)
WLAN: MT7976CN DBDC AX Wi-Fi
Switch: MT7531AE (4x LAN Gigabit ports, 1x WAN Gigabit port)
5G: Quectel RM520N modem
Watchdog: an external WDT connected to GPIO 6 is present and always running;
the built-in Mediatek watchdog is also present and effective, but
not used at the moment.
This porting has been tested only with 1x 5G modems installed (the device
supports up to two).
Installation:
Installation is possible via sysupgrade both in the stock device and
re-branded version. However, in the former case, updating the bootloader is
required.
OpenWrt-based U-Boot Bootloader installation
--------------------------------------------
The firmware flashed in the re-branded device at manifacturing time will
flash an OpenWrt-based U-Boot bootloader with some extra recovery features
(see [1]) at first boot.
To update the bootloader, you need to install the mtd-rw module and
insmod it:
insmod mtd-rw i_want_a_brick=1
Then update relevant flash partitions:
mtd erase u-boot-env
mtd erase BL2
mtd erase FIP
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-preloader.bin BL2
mtd write openwrt-mediatek-filogic-gatonetworks_gdsp-bl31-uboot.fip FIP
And reboot, making sure all previous commands ran succesfully.
If something goes wrong, you can recover your device via the mtk_uartboot
tool.
In my testing, it was possible to start the process even without (un)-plugging
the device, may be handy for remote recovery.
Installation from stock device and firmware
-------------------------------------------
To install vanilla OpenWrt in the stock device (R5000 5G Industrial router
from Yinghua Technologies) running the stock vendor firmware, you will need
to update your bootloader as described in previous section. Remember to use
-F (force upgrade) and -n (not keeping settings).
U-Boot Recovery
---------------
This procedure has been tested only with the OpenWrt-based U-boot bootloader.
Assign your system static IP address 192.168.1.1 and start a TFTP server. The
device will look for an initramfs image named
openwrt-mediatek-filogic-gatonetworks_gdsp-initramfs-kernel.bin
(so you may use openwrt/bin/targets/mediatek/filogic as root dir for your
TFTP server).
Power on the device while keeping the reset button pressed, until you see
a TFTP request from 192.168.1.10. Your environment will be restored to it's
default state.
MAC addresses assignment
------------------------
MAC addresses are assigned slightly differently than in stock firmware. In
particular, the 5 GHz Wi-Fi uses 2.4 GHZ MAC + 1, rather than reusing it with
LA bit set as done in stock firmware. This MAC address is allocated to the
device, so it can be used.
The 2.4 GHz Wi-Fi MAC address is the label MAC. LAN MAC is used to set the
special U-Boot environment ethaddr variable.
device MAC address U-Boot env variable factory partition offset
2.4 GHz Wi-Fi :84 wifi_mac 0x4
5.8 GHz Wi-Fi :85 not present not present
WAN :86 wan_mac 0x24
LAN :87 lan_mac 0x2A
Notes
-----
[1]: the OpenWrt-based U-Boot bootloader you will find installed in the
re-branded device is configured to request for the initramfs image via
TFTP for $gdsp_tftp_tries times before trying normal boot from NOR flash.
Setting this U-Boot environment variable to 0x0 will disable the feature,
which is not implemented in this patch.
[2]: the exposed UART port is connected to ttyS1; the ttyS0 console port is
not exposed.
[3]: the provided bootloader environment has no provision for operating on
BL2 and the FIP partitions. This is an intentional choice to make it
(slightly) more difficult to brick the device.
[4]: it seems GPIO 6 is used both for the "SYS" LED and external WDT.
[5] BL2 expects to find FIP payload at a fixed offset, so some constraints
apply.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit b43194e041)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The GatoNetworks GDSP is a re-branded version of the R5000 5G Industrial
router from Yinghua Technologies.
Advantages over stock bootloader:
1. supports serving the external GPIO WDT, allowing for easier work in U-Boot
shell
2. supports cool features like netconsole, easy recovery, scripting and so on
3. allows using FIT image and image integrity validation
and ultimately gives you much more flexibility to implement your tweaks.
Known issues
------------
To make it easier to operate the device, console I/O multiplexing support has
been enabled in U-Boot configuration. Setting I/O related U-Boot environment
variables to something like "serial,nc" will have the desired effect. Still,
setting these variables to such a value in the persistent environment will
lead to a crash and make it impossible to boot the system or recover it. I
decided to leave it on anyway since I think it can be very practical in
development.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit 7f2c7b3238)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following shellcheck's recommendations:
In scripts/download-check-artifact.sh line 24:
exit $1
^-- SC2086 (info): Double quote to prevent globbing and word splitting.
In scripts/download-check-artifact.sh line 53:
local sum="$(shasum -a 256 "$image_file")";
^-^ SC2155 (warning): Declare and assign separately to avoid masking return values.
In scripts/download-check-artifact.sh line 72:
cd "/tmp/verify.$$"
^-----------------^ SC2164 (warning): Use 'cd ... || exit' or 'cd ... || return' in case cd fails.
In scripts/download-check-artifact.sh line 114:
printf "Keyserver to use? [$keyserver_url] > "
^-- SC2059 (info): Don't use variables in the printf format string. Use printf '..%s..' "$foo".
In scripts/download-check-artifact.sh line 115:
read url; case "${url:-$keyserver_url}" in
^--^ SC2162 (info): read without -r will mangle backslashes.
While at it make it clear, that it is possible to download/check any
build artifacts like even SDK or ImageBuilder.
Link: https://github.com/openwrt/openwrt/pull/16871
(cherry picked from commit 27c2c140b1)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
While checking wiki documentation about GPG signatures checking I found
this nice script and I've thought, that it would be nice to provide it
officially instead of some random internet site.
Usage example:
$ ./scripts/download-check-artifact.sh https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/openwrt-mediatek-filogic-openwrt_one-squashfs-sysupgrade.itb
1) Downloading image file
=========================
########################################### 100.0%
2) Downloading checksum file
============================
########################################### 100.0%
3) Downloading the GPG signature
================================
########################################### 100.0%
4) Verifying GPG signature
==========================
gpg: Signature made Tue 05 Nov 2024 05:21:50 PM UTC
gpg: using EDDSA key 92C561DE55AE6552F3C736B82B0151090606D1D9
gpg: Good signature from "OpenWrt Build System (Nitrokey3) <contact@openwrt.org>" [ultimate]
Primary key fingerprint: 8A8B C12F 46B8 36C0 F9CD B36F 1D53 D187 7742 E911
Subkey fingerprint: 92C5 61DE 55AE 6552 F3C7 36B8 2B01 5109 0606 D1D9
5) Verifying SHA256 checksum
============================
openwrt-mediatek-filogic-openwrt_one-squashfs-sysupgrade.itb: OK
Verification done!
==================
Downloaded artifact placed in '/var/home/ynezz/dev/openwrt/openwrt.git/openwrt-mediatek-filogic-openwrt_one-squashfs-sysupgrade.itb'
Cleaning up.
Adding file in a state as downloaded from https://www.abitare.org/bin/download.sh
References: https://openwrt.org/docs/guide-quick-start/verify_firmware_checksum?s[]=gpg#linux
Signed-off-by: David S. H. Rosenthal <dshr@abitare.org>
Link: https://github.com/openwrt/openwrt/pull/16871
(cherry picked from commit 4c9031fda2)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Add comments to build system makefile functions and variables to help
developers in understanding build system internals and ease the
development process.
This patch adds some documentation examples with proposed doxygen-like
syntax. Hopefully, this would start the discussion and result in
generation of the makefile documentation guidelines.
Signed-off-by: Sergey Matsievskiy <matsievskiysv@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16888
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a72c8c7705)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Edgerouter-X factory images have not built automatically since 19.x due
to images being over 3MB. While it was possible to build custom images
with very stripped down config, this is no longer possible with the size
increases of linux 6.1 and 6.6.
Drop code for generation of factory images, if some dev later wishes to
try custom images they can revert this commit.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Link: https://github.com/openwrt/openwrt/pull/15194
(cherry picked from commit 4d90b79704)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Both packages `ombnia-mcu-firmware` and `omnia-mcutool` would depend on
a specific device. The buildbots however build all devices and therefore
the package isn't build at all, due to unmet dependencies.
While this didn't cause issues with OPKG, APK fails actively due to the
missing packages. Drop the specific dependency, however wants to install
unrelated firmware on any device can do that anyway.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit f35a29d63f)
Link: https://github.com/openwrt/openwrt/pull/17097
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently downstream tools like ASU lack information about kernel
version to find out the relevant kmod build folder on downloads server.
So lets fix it by providing a new `linux_kernel` JSON array which would
for the start provide Linux kernel version, revision and vermagic
information.
"linux_kernel": {
"release": "1",
"vermagic": "b57450c07d3a786158c3601fc5cee57d",
"version": "6.6.61"
},
Fixes: openwrt/openwrt#17036Fixes: efahl/owut#9
Co-developed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Eric Fahlgren <ericfahlgren@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17042
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c857145e03)
Add ubihealthd to the nand-utils package, auto-create UCI config for
each UBI device and launch the daemon on boot.
The default time interval between scrubbing a random PED is 120 seconds
which means that a fully used 128 MiB flash chip gets scrubbed in about
a day and a half. The interval can be adjusted in UCI using the
'interval' option.
Suggested-by: Rodrigo Balerdi <lanchon@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/16973
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 7e287b563a)
7330fa5 initd: mount /sys and /proc with MS_RELATIME
Fixes mounting /proc in unpriviledged user namespace.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1e8505ac4e)
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 0a7b7ef27c)
Edgerouter X currently has its eth1 port on the switch missing since there
is a naming conflict currently.
So, as the root cause is mixing kernel support for DSA interfaces having
predictable names set via "label" property vs others having it assigned
dynamically lets avoid the conflict by using our own custom property as
suggested upstream [1].
So, add support via "openwrt,netdev-name" property and use it on ERX.
Fixes: 2a25c6ace8 ("ramips: get rid of downstream network device label patch")
Fixes: #15643
Link: https://github.com/openwrt/openwrt/pull/17062
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 5695267847)
Fixup capabilities parsing in iw output.
In addition to the normal capabilities iw now also outputs HE MAC, HE
PHY and EHT MAC and EHT PHY capabilities. Exclude them in the parsing.
The grep returns this with mac80211-hwsim:
```
root@OpenWrt:~# iw phy phy0 info | grep 'Capabilities:'
Capabilities: 0x107e
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bfce0000000000000000):
EHT PHY Capabilities: (0x7c0000feffff7f01):
HE PHY Capabilities: (0x02bf000000000000000000):
Capabilities: 0x107e
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfc1f3ffeffff7f37):
HE PHY Capabilities: (0x1cbf000000000000000000):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbfce0000000000000000):
EHT PHY Capabilities: (0xfefffffeffffff7f):
HE PHY Capabilities: (0x1cbf000000000000000000):
Capabilities: 0x107e
```
With busybox 1.36.1 the ht_cap_mask variable will be set to
-72057598332895361. With busybox 1.37.0 it will be set to -1.
Both values are wrong, after this change it will be set to 4222
(0x107E).
Link: https://github.com/openwrt/openwrt/pull/17043
(cherry picked from commit adf958c919)
Link: https://github.com/openwrt/openwrt/pull/17055
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The label-mac does not match the one assigned to the ethernet interface.
Use the mac-address assigned to the wifi interface instead, as it
matches the one found on the device label.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b8b658bc0d)
Trying to use 'package_whatdepends' feature of the ImageBuilder with OPKG
will currently fail as OPKG does not support "list --depends" call at all,
it seems that this is a mixup from the original APK support commit.
So, lets restore 'package_whatdepends' support for OPKG by calling
"whatdepends -A" instead as we used to before APK support.
Fixes: d788ab376f ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/17022
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 52519a59a8)
The original set of stock partitions was kept in the TR4400 v2 port,
with the same partition numbers but their names prefixed with 'stock_'.
This allowed scripts (installation, back to stock, etc) to run on both
stock and OpenWrt firmware. But this triggers warnings in the device
tree compiler, as partitions of the old and new schemes overlap.
This commit fixes the dtc warnings by deleting the stock partitions,
also renumbering some of the remaining MTD partitions in the process.
Additionally, the 'fw_env' partition is set to read-only.
These changes can break existing scripts as well as user configurations
that utilize the 'extra' partition. Users wanting to run old scripts can
do so by reverting to the 23.05 series releases.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16958
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 8ec35a2a15)
The broadcom PHY driver only has to depend upon PTP_1588_CLOCK_OPTIONAL
if NETWORK_PHY_TIMESTAMPING is enabled. The PTP functionality is stubbed
in this case.
Reflect this circumstance in the dependence condition. This allows to
build the driver as a built-in module even if PTP is built as a module.
This is required to include the broadcom PHY module regardless of the
built-setting of the PTP subsystem. On ath79 (and probably more)
targets with Broadcom PHY, Gigabit operation is currently broken as the
PHY driver is only built as a module in case all kernel-packages are
built. Due to this circumstance, affected devices fall back to using the
generic PHY driver.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit cbce32e30c29dc69907c6f4c0ab79dd5d9a8fb28)
Sync patch with upstream version and tag them.
Minor changes done to Pinctrl patch to support older kernel.
Patch automatically refreshed with make target/linux/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit a5d23e3aee)
The Sophos AP15C uses the same hardware as the AP15, but has a reset button.
Based on:
commit 6f1efb2898 ("ath79: add support for Sophos AP100/AP55 family")
author Andrew Powers-Holmes <andrew@omnom.net>
Fri, 3 Sep 2021 15:53:57 +0200 (23:53 +1000)
committer Hauke Mehrtens <hauke@hauke-m.de>
Sat, 16 Apr 2022 16:59:29 +0200 (16:59 +0200)
Unique to AP15C:
- Reset button
- External RJ45 serial console port
Flashing instructions:
This firmware can be flashed either via a compatible Sophos SG or XG
firewall appliance, which does not require disassembling the device, or via
the U-Boot console available on the internal UART header.
To flash via XG appliance:
- Register on Sophos' website for a no-cost Home Use XG firewall license
- Download and install the XG software on a compatible PC or virtual
machine, complete initial appliance setup, and enable SSH console access
- Connect the target AP device to the XG appliance's LAN interface
- Approve the AP from the XG Web UI and wait until it shows as Active
(this can take 3-5 minutes)
- Connect to the XG appliance over SSH and access the Advanced Console
(Menu option 5, then menu option 3)
- Run `sudo awetool` and select the menu option to connect to an AP via
SSH. When prompted to enable SSH on the target AP, select Yes.
- Wait 2-3 minutes, then select the AP from the awetool menu again. This
will connect you to a root shell on the target AP.
- Copy the firmware to /tmp/openwrt.bin on the target AP via SCP/TFTP/etc
- Run `mtd -r write /tmp/openwrt.bin astaro_image`
- When complete, the access point will reboot to OpenWRT.
To flash via U-Boot serial console:
- Configure a TFTP server on your PC, and set IP address 192.168.99.8 with
netmask 255.255.255.0
- Copy the firmware .bin to the TFTP server and rename to 'uImage_AP15C'
- Open the target AP's enclosure and locate the 4-pin 3.3V UART header [4]
- Connect the AP ethernet to your PC's ethernet port
- Connect a terminal to the UART at 115200 8/N/1 as usual
- Power on the AP and press a key to cancel autoboot when prompted
- Run the following commands at the U-Boot console:
- `tftpboot`
- `cp.b $fileaddr 0x9f070000 $filesize`
- `boot`
- The access point will boot to OpenWRT.
Signed-off-by: David Lutz <kpanic@hirnduenger.de>
(cherry picked from commit a7abc7ec3b)
/sbin/pkg_check uses opkg and is not even packaged when using the
default opkg configuration. remove it when using apk too.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 0ce237a20c)
8dfead68c202 wifi: mt76: mt7915: hold dev->mutex while interacting with the thermal state
d508a6eb935d wifi: mt76: mt7996: use mac80211 .sta_state op
57019e663f57 wifi: mt76: add code for emulating hardware scanning
dc4c2bdf7c56 wifi: mt76: add support for allocating a phy without hw
8cd0263f92e1 wifi: mt76: rename struct mt76_vif to mt76_vif_link
99df84d62883 wifi: mt76: add vif link specific data structure
dcc6f158d759 wifi: mt76: mt7996: split link specific data from struct mt7996_vif
d388deab9e73 wifi: mt76: initialize more wcid fields mt76_wcid_init
d026be405c54 wifi: mt76: add chanctx functions for multi-channel phy support
0b05795ca81c wifi: mt76: remove dev->wcid_phy_mask
0b526090de95 wifi: mt76: add multi-radio support to a few core hw ops
aeedee5c0a2c wifi: mt76: add multi-radio support to tx scheduling
fc0ff17b53ff wifi: mt76: add multi-radio support to scanning code
f19cbcf83400 wifi: mt76: add multi-radio remain_on_channel functions
42429ae0eaf6 wifi: mt76: mt7996: use emulated hardware scan support
f9d593d4a6b4 wifi: mt76: mt7996: pass wcid to mt7996_mcu_sta_hdr_trans_tlv
807090b28661 wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support
252baa7bf477 wifi: mt76: mt7996: prepare mt7996_mcu_add_beacon for MLO support
9ee990050305 wifi: mt76: mt7996: prepare mt7996_mcu_set_tx for MLO support
bf12cc404334 wifi: mt76: mt7996: prepare mt7996_mcu_set_timing for MLO support
60bf2bef95dc wifi: mt76: connac: prepare mt76_connac_mcu_sta_basic_tlv for MLO support
1289737e12a8 wifi: mt76: mt7996: prepare mt7996_mcu_update_bss_color for MLO support
7c00df0e7e57 wifi: mt76: connac: rework connac helpers
484e3f289a40 wifi: mt76: mt7996: move all debugfs files to the primary phy
d258f4e3e1ca wifi: mt76: mt7996: switch to single multi-radio wiphy
c246fa545119 wifi: mt76: mt7996: fix monitor mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 6720c4ccba)
e93f6c3fc729 main: fix format string related warnings for log/debug printf functions
6ab44a2413f9 fix signed/unsigned comparison warnings
4fe997b61d7d system-dummy: add system_if_apply_settings_after_up
992d33cb42a6 ubus: add notifications on wireless device state changes
34eb11eb6f5c device/interface: add "tags" attribute from config to status dump
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 5f68e24333)
This allows annotating wifi interfaces in the config in a way that can be
queried through wifi status. One example use case is to mark wifi interfaces
for use with specific services without having to explicitly reference the
(often unnamed) sections from elsewhere.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a3ec35cadb)
This reverts commit e1043a746a, that
attempts to nest partitions that overlap but are not nested. This
causes the 'ubi' partition to be truncated, making rootfs inaccessible
and bricking the device.
Also, had this commit worked, it would have renumbered MTD partitions
in a way that would have broken documented scripts for installation and
update of main and recovery OSes, making backups, return to stock, etc,
and broken user configurations that put the 'extra' partition to use.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16944
Signed-off-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit 0e59eaa796)
The MAC address offset in 128G version is 0x442a (+1 compared to 64g
version). As the mac stored in config partition is plain text format
so simply call mtd_get_mac_ascii to work on both version.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit c0c480daa7)
The last "syscfg" partition of the OEM firmware turns out to be a
UBIFS used to store user data, just as the "rootfs_data" of OpenWrt,
so it should be reasonable to absorb it into the "ubi" partition.
Factory installations via either OEM firmware or tftp, or by forcibly
flashing factory image to mtd5 (firmware) partition with mtd tool are
confirmed working, but the UBI remaining inside "syscfg" partition
could break upgrade. Fortunately, installing kmod-mtd-rw and erasing
"syscfg" partition before upgrade is confirmed working, in which case,
"ubi" will automatically expand to the blank space once occupied by
the former mtd8 (syscfg), with the total block number increased, but
the UBIFS for rootfs_data will not automatically claim the newly
available space (since it is created when mtd8 still exists, and
sysupgrade does not set "autoresize" flag to rootfs_data). These space
will be claimed during the next upgrade, when rootfs_data is removed
and created again.
Fixes: 50f727b773 ("ath79: add support for Linksys EA4500 v3")
Signed-off-by: Edward Chow <equu@openmail.cc>
Link: https://github.com/openwrt/openwrt/pull/14791
Signed-off-by: Robert Marko <robimarko@gmail.com>
109fa41b2321 system: fix description value from os-release
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 09a8b4920c)
Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f.
Fixes: a85e18b53f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
(cherry picked from commit 6490c88c75)
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
Mass production units will get 16 assigned MAC addresses. This allows each phy
to spawn up to 7 VAPs which will each have unique MAC without needing the
private bit.
Signed-off-by: John Crispin <john@phrozen.org>
The mediatek target requires refreshing after recent additions.
Fixes: cfe8e6e75f ("mediatek: add support for Realtek RTL8261n 10G PHYs")
Fixes: ddfae94a14 ("mediatek: add support for swapping the polarity on usxgmii interfaces")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Assign pwm function of PWM0 pin to the pwm-fan.
This is mostly just cosmetics as it basically reflects the default
setting of that pin.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add additionals possible pinctrl group for pwm2~7 on pins
pin 4 (GPIO_A) pwm7
pin 58 (JTAG_JTDI) pwm2
pin 59 (JTAG_JTDO) pwm3
pin 60 (JTAG_JTMS) pwm4
pin 61 (JTAG_JTCLK) pwm5
pin 62 (JTAG_JTRST_N) pwm6
They can be useful e.g. on the BPi-R4 as in that way pwm2~6 can be exposed
on the 26-pin header (pwm6 always, pwm2~5 instead of the full UART).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Using the arrow keys to navigate the U-Boot menu often leads to being
dropped into the U-Boot shell unexpectedly.
This can be prevented in most cases by improving the logic to detect the
arrow key ESC sequence and only reprinting the menu if actually needed.
Also enable CONFIG_SERIAL_RX_BUFFER for all boards as it helps preventing
the remaining cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step 2.
In the build step 2 it may be left out if we build it using a different
target.
Fixes: #16857
Link: https://github.com/openwrt/openwrt/pull/16859
Signed-off-by: Robert Marko <robimarko@gmail.com>
A factory image for DNA EX400 depends on an initramfs image and they
were explicitly removed from the imagebuilder recently. Now the factory
image creation fails miserably and it also affects custom image creation
with the firmware selector.
Add the initramfs kernel to the staging so that it's shipped with the
imagebuilder. Also remove a image build target added solely for DNA EX400.
Tested by creating a factory and syspupgrade images locally with
the imagebuilder and verified their functionality.
Related work
c85348d9ab ("imagebuilder: remove initramfs image files")
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
---
v4: use append-image-stage, remove Build/kernel-initramfs-bin
v3: adjust commit subject
v2: remove fix for inconsistent line ending elsewhere in the file
Link: https://github.com/openwrt/openwrt/pull/16659
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream stable is slow at picking this up and several systems
are regressing. Add the patch locally in OpenWrt.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
@KA2107 reported that opkg is not able to verify the artifact signatures
produced by buildbot using the usign 24.10 release keys. So lets fix it
by actually adding the 24.10 usign key with d310c6f2833e97f7 fingerprint
into the openwrt-keyring package.
Fixes: #16850
Reported-by: @KA2107
Fixes: a535cfc09e ("openwrt-keyring: add OpenWrt 24.10 release build usign key")
References: 2d03f27f0f07 ("openwrt-keyring: make opkg use 22.03 usign key")
Signed-off-by: Kuan-Yi Li <kyli@abysm.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [commit description]
The clocks for SPI busses were named wrongly which resulted in the
spi-mt65xx driver not requesting them. This has apparently been
worked around by marking the clocks required for SPI0 which is used
for SPI-NOR and SPI-NAND flash chips as critical.
Fix the device tree for all 3 generic SPI host controllers and no
longer mark clocks as critical.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b173ab730)
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
+bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
+bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
+bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
+bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
+bootmenu_8=Reboot.=reset
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
+boot_first=if button reset ; then led $bootled_rec on ; run boot_tftp_recovery ; setenv flag_recover 1 ; run boot_default ; fi ; bootmenu
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
+boot_production=led $bootled_pwr on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led $bootled_pwr off
+boot_recovery=led $bootled_rec on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led $bootled_rec off
+boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
+boot_tftp_forever=led $bootled_rec on ; while true ; do run boot_tftp_recovery ; sleep 1 ; done
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
+ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
+ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
+ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
+ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
+ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
+ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
+ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
+_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
+_firstboot=setenv _firstboot ; run _switch_to_menu ; run _init_env ; run boot_first
+bootmenu_1=Boot system via TFTP.=run boot_tftp ; run bootmenu_confirm_return
+bootmenu_2=Boot production system from NAND.=run boot_production ; run bootmenu_confirm_return
+bootmenu_3=Boot recovery system from NAND.=run boot_recovery ; run bootmenu_confirm_return
+bootmenu_4=Load production system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_production ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_5=Load recovery system via TFTP then write to NAND.=setenv noboot 1 ; setenv replacevol 1 ; run boot_tftp_recovery ; setenv noboot ; setenv replacevol ; run bootmenu_confirm_return
+bootmenu_6=[31mLoad BL31+U-Boot FIP via TFTP then write to NAND.[0m=run boot_tftp_write_fip ; run bootmenu_confirm_return
+bootmenu_7=[31mLoad BL2 preloader via TFTP then write to NAND.[0m=run boot_tftp_write_bl2 ; run bootmenu_confirm_return
+bootmenu_8=Reboot.=reset
+bootmenu_9=Reset all settings to factory defaults.=run reset_factory ; reset
+boot_first=if button reset ; then led $bootled_status on ; run boot_default ; fi ; bootmenu
+boot_default=if env exists flag_recover ; then else run bootcmd ; fi ; run boot_recovery ; setenv replacevol 1 ; run boot_tftp_forever
+boot_production=led $bootled_status on ; run ubi_read_production && bootm $loadaddr#$bootconf ; led bootled_status off
+boot_recovery=led $bootled_status on ; run ubi_read_recovery && bootm $loadaddr#$bootconf ; led bootled_status off
+boot_ubi=run boot_production ; run boot_recovery ; run boot_tftp_forever
+boot_tftp_forever=led $bootled_status on ; while true ; do run boot_tftp ; sleep 1 ; done
+boot_tftp_production=tftpboot $loadaddr $bootfile_upg && env exists replacevol && iminfo $loadaddr && run ubi_write_production ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+boot_tftp_recovery=tftpboot $loadaddr $bootfile && env exists replacevol && iminfo $loadaddr && run ubi_write_recovery ; if env exists noboot ; then else bootm $loadaddr#$bootconf ; fi
+ubi_create_env=ubi check ubootenv || ubi create ubootenv 0x100000 dynamic || run ubi_format ; ubi check ubootenv2 || ubi create ubootenv2 0x100000 dynamic || run ubi_format
+ubi_format=ubi detach ; mtd erase ubi && ubi part ubi ; reset
+ubi_prepare_rootfs=if ubi check rootfs_data ; then else if env exists rootfs_data_max ; then ubi create rootfs_data $rootfs_data_max dynamic || ubi create rootfs_data - dynamic ; else ubi create rootfs_data - dynamic ; fi ; fi
+ubi_read_production=ubi read $loadaddr fit && iminfo $loadaddr && run ubi_prepare_rootfs
+ubi_read_recovery=ubi check recovery && ubi read $loadaddr recovery
+ubi_remove_rootfs=ubi check rootfs_data && ubi remove rootfs_data
+ubi_write_production=ubi check fit && ubi remove fit ; run ubi_remove_rootfs ; ubi create fit $filesize dynamic && ubi write $loadaddr fit $filesize
+ubi_write_recovery=ubi check recovery && ubi remove recovery ; run ubi_remove_rootfs ; ubi create recovery $filesize dynamic && ubi write $loadaddr recovery $filesize
+_init_env=setenv _init_env ; run ubi_create_env ; saveenv ; saveenv
+_firstboot=setenv _firstboot ; run ethaddr_factory ; run _switch_to_menu ; run _init_env ; run boot_first
+bootmenu_confirm_return=askenv - Press ENTER to return to menu ; bootmenu 60
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
